Polymer 4D printing: Advanced shape-change and beyond

4D printing is an exciting branch of additive manufacturing. It relies on established 3D printing techniques to fabricate objects in much the same way. However, structures which fall into the 4D printed category have the ability to change with time, hence the “extra dimension.” The common perception of 4D printed objects is that of macroscopic single-material structures limited to point-to-point shape change only, in response to either heat or water. However, in the area of polymer 4D printing, recent advancements challenge this understanding. A host of new polymeric materials have been designed which display a variety of wonderful effects brought about by unconventional stimuli, and advanced additive manufacturing techniques have been developed to accommodate them. As a result, the horizons of polymer 4D printing have been broadened beyond what was initially thought possible. In this review, we showcase the many studies which evolve the very definition of polymer 4D printing, and reveal emerging areas of research integral to its advancement.     

Characteristics of black carbon aerosol in Jiaxing,China during autumn 2013

We conducted measurements of black carbon（BC） aerosol in Jiaxing,China during autumn from September 26 to November 30,2013.We investigated temporal and diurnal variations of BC,and its correlations with meteorological parameters and other major pollutants.Results showed that hourly mass concentrations of BC ranged from 0.2 to 22.0 μg/m³,with an average of 5.1 μg/m³.The diurnai variation of BC exhibited a bimodal distribution,with peaks at 07:00 and 18:00.The morning peak was larger than the evening peak.The mass percentages of BC in PM_2.5 and PM₁₀ were 7.1%and 4.8%,respectively.The absorption coefficient of BC was calculated to be 44.4 Mm^-1,which accounted for 11.1%of the total aerosol extinction.BC was mainly emitted from local sources in southwestern Jiaxing where BC concentrations were generally greater than 11 μg/m³ during the measurement period.Correlation analysis indicated that the main sources of BC were motor vehicle exhaust,and domestic and industrial combustion.     

Numerical simulation and structure optimization of a liquid–vapor separation plate condenser

Journal of Thermal Analysis and Calorimetry - Based on innovative design, a liquid–vapor separation plate condenser with excellent heat transfer performance is invented. It takes less time to...     

溶胶-凝胶制备技术与新型催化材料Ⅲ.溶胶粒子表面修饰方法制备催化膜

提出用溶胶粒子表面修饰方法，结合溶胶凝胶技术制备无机催化膜．该方法的基本原理是利用合适的金属配合物在胶粒表面的吸附作用，经溶胶凝胶过程，将活性组分结合到无机膜中．实验测定结果表明：（ＮｉＥＤＴＡ）２－，ＶＯ－３，ＭｏＯ２－４，（Ｐｄ（ＮＨ３）４）２＋，ＰｄＣｌ２－４，ＰｔＣｌ２－６和ＲｈＣｌ３－６可用来修饰ＡｌＯＯＨ溶胶．以Ｐｄ／γＡｌ２Ｏ３催化膜的制备为例，经三次溶胶凝胶过程，可制得无裂缺的厚度为９μｍ的Ｐｄ／γＡｌ２Ｏ３催化膜，膜材料的平均孔直径为６ｎｍ，Ｐｄ被均匀地分布在膜的顶层，其平均粒径为２３ｎｍ．     

A New Type of Terahertz Waveguides

A new type of THz waveguides, which employs a solid polyethylene rod as the core and polyethylene tubes in a periodic array of square lattice as the cladding, is proposed. Optical properties of this new THz waveguide, especially in dispersion, confinement loss and single mode property, are investigated in detail with the plane wave expansion method and the beam propagation method. Numerical results demonstrate that the new THz waveguide can reach not only low dispersion but also low confinement loss at single mode propagation. Therefore, the square lattice structure is a better candidate as THz waveguides than the triangular ones.     

电感耦合等离子体原子发射光谱法测定中药方剂煎煮液中的微量元素

本文采用HNO3－H2O2对中药方剂煎煮液进行处理，拟定了电感耦合等离子体原子发射光谱法同时测定试样中12个微量元素的方法，选择了仪器的最佳工作条件，考察了基本效应的影响。在选定条件下，12个微量元素的检出限为0．10－5．0ng/g，相对标准偏差为0.10%-9.5%(n=10),加标回收率为85％－103％。该方法简单、快速，已用于大量样品的检测，分析结果满意。     

金属薄膜制备及物性测量系列实验

介绍了由模拟真空实验和“金属薄膜的制备”、“金属薄膜厚度的测量”、“金属薄膜电阻率的测量”,以及“金属薄膜生长过程的动态监测”等4个实验组成的金属薄膜制备与物性测量系列实验.这组实验与现代科学技术发展联系紧密,仪器设备可靠,操作简单,适合于普通物理实验阶段的研究性教学.