LAXS investigation of finger phantoms

Osteoporosis is a bone condition that is caused mainly by the degradation of trabecular and cortical bone resulting in the decrease of bone strength and eventually leads to bone fracture. A low angle X-ray scattering (LAXS) system that uses mainly the coherent scattering process for the characterisation of materials was constructed to study such bone conditions. Several finger phantoms were fabricated to simulate bone of varying densities. The LAXS method was able to identify the changes in bone density quite well by comparing energy dispersive X-ray diffraction patterns as well as the angular patterns. Quantitative information can be extracted from such patterns that relate to bone loss. Signature patterns at low exposure times were produced in order to reduce the dose received with reasonable identification power but at slightly higher statistical errors compared with long exposure patterns. Use of other parameters to increase the sensitivity was attempted.     

Radiation pasteurised oil palm empty fruit bunch fermented with Pleurotus sajor-caju as feed supplement to ruminants

In solid state fermentation, Pleurotus sajor-caju has been found to be able to degrade at least 30% oil palm empty Fruit Bunch (EFB) fibre leaving 70 % useful materials. Conditions under which fermentation carried out were investigated. It was found that, in the temperature range between 25– 28 °C, relative ph between 6–8, moisture between 60–70 % and medium composition of CaCO₃: rice bran 2 %: 5 % were the optimum conditions. The results showed in fermented products that, there were substantial reduction in cellulosic component such as Crude Fiber (CF, 18 %); Acid Detergent Fibre (ADF, 45 %), Neutral Detergent Fibre (NDF, 61 %) and Acid Detergent Lignin (ADL, 14 %). However, Crude Protein (CP, 10%) increased resulted from single cell protein enrichment of mycelial microbial mass. The mass reductions of substrate in fermentation process corresponds to the CO₂ released during fermentation. Hence, attributable to the decreased in content of CF, ADF, NDF, and ADL. The digestibility study has also been carried out to determine the useful level of this product to ruminant. Aflatoxin content was detected low in both the initial substrates and products. Based on nutritional value and low content of aflatoxin, the product is useful as a source of roughage to ruminant.     

A lead(II) ion selective electrode via a metal complex of poly(hydroxamic acid)

A new lead(II) electrode has been constructed with poly(hydroxamic acid) (PHXA) as the active material and silicone rubber as the supporting material. The electrode gave near Nerstian response over the concentration range 4 × 10⁻⁵−1 × 10⁻²M lead(II). The detection limit of the electrode is approximately 4 × 10⁻⁶M and the electrode works well in the pH range 4.5–6.0. The response time was 50–120 sec over the whole concentration range and the electrode has a working life of at least 4 weeks. Iron(III) severely poisoned the electrode membrane. Nickel(II) and mercury(II) gave very strong interference compared to copper(II), silver(I), cobalt(II), sodium(I), potassium(I), zinc(II) and cadmium(II) which gave some or little interference. Values determined with atomic absorption (AAS) and a commercial lead(II) electrode were in good agreement with those measured with the lead(II) electrode reported here.     

Novel filled polymer composites prepared from in situ polymerization via a colloidal approach: II. Blends of kaolin/Nylon-6 in situ composites with conventional Nylon-6 and -66

A novel in situ composite comprised of kaolin clay fillers and polyamide 6 (Nylon-6) was synthesized via a colloidal approach by suspending kaolin particles in aqueous caprolactam and then polymerizing the caprolactam under elevated temperature and pressure. This in situ polymerization technique enables the deposition of nylon molecules directly onto the filler surface. It offers a much larger contact surface area for the nylon molecules to interact with the filler particles and enhances filler/matrix interaction through polymer miscibility. The kaolin particles were shown to be uniformly dispersed in Nylon-6 matrix without appreciable agglomeration. In the highly clay-loaded composites such as the 50/50 kaolin/Nylon-6 in situ composite, the deposited nylon molecules probably form a coated layer on the filler particles. This kind of nylon coated fillers may be applied as a reinforcing entity to commercial Nylon-6 or −;66 by improving particle dispersion and melt processability. The 50/50 kaolin/Nylon-6 in situ composites have been used as a masterbatch for blending with commercial Nylon-6 and Nylon-66 to take advantage of their good properties and to reduce cost. Rheology and mechanical properties of the masterbatch/nylon composites have been investigated in comparison with those of the conventional melt-mixed composites. The improvement of rheological and mechanical properties of the in situ composites has been discussed in relation to the composite structure. © 1996 John Wiley & Sons, Inc.     

Novel filled polymer composites prepared from in situ polymerization via a colloidal approach: I. Kaolin/Nylon-6 in situ composites

A mineral-filled in situ composite was prepared by a colloidal approach by first suspending kaolin filler particles in aqueous caprolactam, and then polymerizing caprolactam in situ at high pressure and temperature. The purpose of this colloidal in situ polymerization is to improve particle dispersion and to enhance interaction of the filler to the polymer matrix. X-ray diffraction studies of the in situ kaolin/Nylon-6 composites revealed that the x-ray peak corresponding to the α-crystal form of Nylon-6 diminished with increasing kaolin loading, while the γ-crystal structure became more pronounced. The degree of crystallinity of Nylon-6 remained fairly unchanged with the kaolin loading level in the in situ composites. Calorimetric and dynamic mechanical studies exhibited that the glass transition temperature of the resulting composite increased significantly with increase in kaolin concentration, suggesting strong filler-matrix interaction at the kaolin/Nylon-6 interface. Scanning electron microscopic (SEM) results showed uniform filler dispersion in the in situ composites relative to the conventional melt-mixed composites. Modulus and tensile strength of these in situ composites were found to be distinctively higher than that of the conventional melt-mixed kaolin/Nylon-6 composites. However, as typical for composite materials, drawability and fracture toughness decreased with increasing kaolin loading. © 1996 John Wiley & Sons, Inc.     

Modeling a clinical incineration process using fuzzy autocatalytic set

In this paper we have investigated and explored the realm of fuzzy graph in its relation to autocatalytic sets. A new concept namely fuzzy autocatalytic set have been defined. This relation has produced some results in the forms of theorems which have been proven. A clinical waste incineration process has been modeled using this new concept indicates to be more accurate than using crisp graph.     

A 119Sn Mössbauer Spectroscopic Investigation of Tin Complexes with Amidines

Several novel tin(IV) adducts of amidines, [SnClPh₃L], [SnCl₂Ph₂L] and [SnBr₄L] {L=N,N-diphenylacetamidine (Hdpac) or N,N-diphenylbenzamidine (Hdpba)}, were prepared and investigated by Mössbauer spectroscopy which was an important tool for the elucidation of bonding and structural features. The resulting Mössbauer data also led to the conclusion that the tin(IV) centre for the adduct [SnClPh₃L] is pentacoordinated in a trigonal bipyramidal arrangement and hexacoordinated for [SnCl₂Ph₂L] and [SnBr₄L] in a geometric patterns of an octahedral. The amidines act as monodentate ligands to the metal centre for the former and bidentate for the latter.     

MHD mixed convection flow near the stagnation-point on a vertical permeable surface

The steady magnetohydrodynamic (MHD) mixed convection boundary layer flow of a viscous and electrically conducting fluid near the stagnation-point on a vertical permeable surface is investigated in this study. The velocity of the external flow and the temperature of the plate surface are assumed to vary linearly with the distance from the stagnation-point. The governing partial differential equations are first transformed into ordinary differential equations, before being solved numerically by a finite-difference method. The features of the flow and heat transfer characteristics for different values of the governing parameters are analyzed and discussed. Both assisting and opposing flows are considered. It is found that dual solutions exist for both cases, and the range of the mixed convection parameter for which the solution exists increases with suction.     

Similarity solutions for flow and heat transfer over a permeable surface with convective boundary condition

The steady laminar boundary layer flow over a permeable flat plate in a uniform free stream, with the bottom surface of the plate is heated by convection from a hot fluid is considered. Similarity solutions for the flow and thermal fields are possible if the mass transpiration rate at the surface and the convective heat transfer from the hot fluid on the lower surface of the plate vary like x^−1/2, where x is the distance from the leading edge of the solid surface. The governing partial differential equations are first transformed into ordinary differential equations, before being solved numerically. The effects of the governing parameters on the flow and thermal fields are thoroughly examined and discussed.