Solid Phase Extraction and Simultaneous Spectrophotometric Determination of Trace Amounts of Copper and Iron Using Mixture of Ligands

 A novel sensitive and simple method for rapid and selective extraction, preconcentration and determination of iron (as its bathophenanthroline complex) and copper (as its neocuproine complex) using octadecyl silica cartridges and dual wavelength spectrophotometry is presented. The dual wavelength method (533 nm for the iron-bathophenanthroline and 454 nm for the copper-neocuproine as the analytical wavelength) is used to eliminate spectral interferences. Extraction efficiency and the influence of flow rates of sample solution and eluent, pH, amount of neocuproine, bathophenanthroline and hydroxylamine hydrochloride, type and least amount of eluent for elution of iron and copper complexes from cartridge, break-through volume and limit of detection are evaluated. The effects of various cationic and anionic interferences on percent recovery of iron and copper are also studied. Extraction efficiencies >95% are obtained by elution of cartridges with minimal amount of organic solvent. Iron and copper were determined in the range of 3–100 ng mL⁻¹. The limits of detection are 0.98 and 1.13 ng mL⁻¹ for iron and copper, respectively. The proposed method is applied successfully to the determination of both analytes in river, tap and well water samples. Author for correspondence. E-mail: yyamini@modares.ac.ir Received September 18, 2002; accepted December 12, 2002 Published online May 5, 2003     

HPLC and GC Methods for Determination of Lubricants and Their Evaluation in Analysis of Real Samples of Polyethylene

High performance liquid chromatography (HPLC) and gas chromatography (GC) are introduced for analysis of polymer lubricants (stearamide, oleamide and erucamide). In the HPLC method, a reverse phase octadecylsilane (ODS) column along with acetonitrile/methanol (60:40) as a mobile phase were used. Detection of analytes was performed by a UV detector at 202 nm. The analysis time was less than 8 min. In the GC method, polar capillary column and flame ionization detector (FID) were used for separations and detection, respectively. The analysis time by GC was longer than HPLC and was about 30 min. Limits of detection, linear range and repeatability of both methods are similar, but determination of oleamide in real samples by HPLC method is difficult due to complexity of the initial part of HPLC chromatogram in polyethylene samples. That problem is not observed in the GC method. Detection limits in both methods for all analytes are lower than 0.003% which are much lower than the amount of lubricants in commercial polymers (0.05–0.2%).     

Preparation and characterization of fibres from a thermotropic liquid crystal polyester with non-coplanar biphenylene units

Abstract

Fibres were prepared from the nematic melt of poly(2,2′-dimethyl-4,4′-biphenylene phenylterephthalate). The phenyl substitution in the terephthalic acid moiety in combination with the non-coplanar biphenyl moiety prevent crystallization of this thermotropic polyester. Oriented fibres were prepared by two different methods. Similarly to other thermotropic liquid crystal polymer fibres, chain orientation can be achieved by an elongational flow in a down draw process. This polyester also allows tensile deformation of the spun fibres around the glass transition temperature. In both routes similar degrees of orientation and mechanical properties were obtained. Tensile moduli in the order of 40–45 GPa and tensile strengths up to 550–650 MPa were obtained. The orientation function values were determined to be in the order of 0·8–0·9. A comparison with other unsubstituted thermotropic liquid crystal polyesters at the same level of orientation revealed that the moduli are the same, although the substituents increase the chain diameter. This result may be attributed to an increase of the apparent shear modulus due to an interlocking mechanism of the rigid lateral substituents.     

Thermodynamic simulation of performance of a dual cycle with stroke length and volumetric efficiency

This article presents finite-time thermodynamics analysis of an irreversible air standard dual cycle. An irreversible dual cycle model which is more close to practice is established. In this model, the effects of stroke length and volume efficiency by considering the nonlinear relation between the specific heats of working fluid and its temperature, the frictional loss, the internal irreversibility, and heat transfer loss are analyzed. The results show that if compression ratio is less than certain value, the power output increases with increasing stroke length, while if compression ratio exceeds certain value, the power output first increases and then starts to decrease with increasing stroke length. With further increase in compression ratio, the increase of stroke length results in decreasing the power output. The results also show that, throughout the compression ratio range, the power output increases with the increasing volumetric efficiency. The results obtained in this study are of importance to provide good guidance for performance evaluation and improvement of practical internal combustion engines.     

Application of a dispersive micro‐solid‐phase extraction method for pre‐concentration and ultra‐trace determination of cadmium ions in water and biological samples

A method for the trace determination of cadmium ions in water, human urine and human blood serum samples using ultrasonic‐assisted dispersive micro‐solid‐phase extraction (UA‐D‐μSPE) was developed. Silica‐coated magnetic nanoparticles were coated with polythiophene, and the resulting sorbent was characterized using thermogravimetry, differential thermal analysis, scanning electron microscopy, Fourier transform infrared spectrometry and X‐ray diffraction. Following UA‐D‐μSPE, cadmium ions were quantified using graphite furnace atomic absorption spectrometry. A Box–Behnken design was used for optimization of important sorption and desorption parameters in UA‐D‐μSPE: in the sorption step, pH of solution, sorption amount and sonication time for sorption; in the desorption step, concentration of eluent, volume of eluent and sonication time. The optimum conditions for the method were: pH of solution, 7.5; sonication time for sorption, 3 min; sorption amount, 35 mg; type and concentration of eluent, HCl and 1.1 mol l^?1; volume of eluent, 360 μl; sonication time for desorption, 110 s. Under the optimized conditions the limit of detection and relative standard deviation for the detection of cadmium ions by UA‐D‐μSPE were found to be 0.8 ng l^?1 and <6%, respectively.