Enhanced Power Density of Alcohol Biofuel Cell by Polymer-assisted Crosslinks of 3D Graphene on Carbon Paper as the Bioanode

Herein, we successfully construct the 3D biocompatible graphene through crosslinking 2D graphene nanosheet onto carbon fiber paper with poly(diallyldimethylammonium chloride) (PDDA) as anode of the alcohol biofuel cell. Compared with the bioanode without 3D graphene, the current density and output power of PDDA-graphene-ADH bioanode is increased by 23 % and 41 % at a high concentration of ethanol at pH 8.9, suggesting the stabilization role of graphene in enzyme loading. The study provides us a deep analysis on structures and performances of the bioanode incl. electrochemistry, X-ray photoelectron spectra, and atomic force microscopy images, which is significant to develop the new methods to construct 3D porous electrodes in energy conversion device.     

Preparation and gas sensing activity of La and Y co-doped titania nanoparticles

Journal of Sol-Gel Science and Technology - A novel gas sensing material, La–Y co-doped TiO2 nanoparticles, was synthesized by sol–gel method and applied to detect organic pollutants...     

煤直接液化油中混合酚的分离研究

利用分子筛择形特点，对煤直接液化油中的混合酚实施高效分离。本研究选取间甲酚和对甲酚作为分离煤直接液化油馏分段混合酚的模型化合物，采用化学液相沉积法对HZSM-5吸附剂的孔口结构进行改变，分析分子筛硅铝比及颗粒粒径对模型化合物间甲酚和对甲酚吸附分离性能的影响，以获得高性能固相吸附剂，并将其应用于180-190℃馏分段混合酚分离。结果表明，当分子筛硅铝比为25、粒径为3-5 μm时，分子筛的孔口结构调节效果最优；当正硅酸乙酯的最小用量为0.2 mL/g时，固相吸附剂的吸附量为0.03 g/g，对甲酚选择性高于95%。由于外表面沉积物对吸附剂的孔口结构变化，导致对甲酚选择性的提高。进一步采用HZSM-5（1）吸附剂对真实煤直接液化油混合酚的分离中发现，苯酚和对甲酚的选择性均达到100%。     

基于串联两阶段网络DEA模型的供应链规模收益分析

数据包络分析(DEA)是评价供应链系统(Supply chain system)间相对有效性的一种重要的工具,但是传统的DEA不考虑供应链的内部结构,对系统效率评价偏高;而本文所研究两阶段串联供应链系统,考虑把部分中间产品作为最终产品输出,增加额外中间投入的情形.基于所提出的供应链系统结构,本文建立相应的串联结构下的网络DEA模型,并针对所建立模型进行相关理论的研究,给出了串联结构下的生产可能集和规模收益情况判定方法.最后,进行数值实验,以验证我们提出的结论.     

Lipase‐Supported Metal–Organic Framework Bioreactor Catalyzes Warfarin Synthesis

A green and sustainable strategy synthesizes clinical medicine warfarin anticoagulant by using lipase‐supported metal–organic framework (MOF) bioreactors (see scheme). These findings may be beneficial for future studies in the industrial production of chemical, pharmaceutical, and agrochemical precursors.     

Path to achieving molecular dispersion in a dense reactive mixture

A uniform dispersion of reactants is necessary to achieve a complete reaction involving multicomponents. In this study, we have examined the role of plasticizer in the reaction of two seemingly unlikely reactants: a highly crystalline hexamethylenetetramine (HMTA) and a strongly hydrogen bonded phenol formaldehyde resin. By combining information from NMR, infrared spectroscopy and differential scanning calorimetry, we were able to determine the role of specific intermolecular interactions necessary for the plasticizer to dissolve the highly crystalline HMTA and to plasticize the phenol formaldehyde resin in this crosslinking reaction. The presence of the plasticizer increased the segmental mobility, disrupted the hydrogen bonded matrix, and freed the hydroxyl units, which further increased the solubility of the HMTA. Both the endothermic and exothermic transitions are accounted for in the calorimetric data obtained. For the first time, it is possible to obtain the effective molar ratio of each component needed to complete the crosslinking reaction efficiently. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1519–1526     

光束发散度对紫外写入光纤光栅的影响

用傅里叶衍射光学分析了准分子激光束发散度对于光纤光栅制备的影响，发现光束发散角使光纤光栅的布拉格波长发生改变，相位版后干涉场沿光纤轴向和径向不均匀，对制备30dB高反射率光纤光栅造成困难。实验结果与理论分析基本一致，相对于理想平行光束情况，会聚光束使得光纤光栅布拉格波长出现在短波一边，发射光束使得光纤光栅布拉格波长出现在长波一边。     

The Calibrating Theory in the Network Parameters Measurement of Microwave and MMW Devices

The paper introduces a special system calibration technology in s-parameters measurement of microwave and millimeter wave devices. The 8-term errors module is built by analyzing the signals flowing in the measurement system. Then the calibration technology using non-standard kits is designed on the base. Finally, the experiment using the calibration technology is introduced.     

Nanostructured thermoset epoxy resin templated by an amphiphilic poly(ethylene oxide)‐block‐poly(dimethylsiloxane) diblock copolymer

An amphiphilic poly(ethylene oxide)‐block‐poly(dimethylsiloxane) (PEO–PDMS) diblock copolymer was used to template a bisphenol A type epoxy resin (ER); nanostructured thermoset blends of ER and PEO–PDMS were prepared with 4,4′‐methylenedianiline (MDA) as the curing agent. The phase behavior, crystallization, hydrogen‐bonding interactions, and nanoscale structures were investigated with differential scanning calorimetry, Fourier transform infrared spectroscopy, transmission electron microscopy, and small‐angle X‐ray scattering. The uncured ER was miscible with the poly(ethylene oxide) block of PEO–PDMS, and the uncured blends were not macroscopically phase‐separated. Macroscopic phase separation took place in the MDA‐cured ER/PEO–PDMS blends containing 60–80 wt % PEO–PDMS diblock copolymer. However, the composition‐dependent nanostructures were formed in the cured blends with 10–50 wt % PEO–PDMS, which did not show macroscopic phase separation. The poly(dimethylsiloxane) microdomains with sizes of 10–20 nm were dispersed in a continuous ER‐rich phase; the average distance between the neighboring microdomains was in the range of 20–50 nm. The miscibility between the cured ER and the poly(ethylene oxide) block of PEO–PDMS was ascribed to the favorable hydrogen‐bonding interaction. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3042–3052, 2006     

置换模,ρ置换模与Conlon比析

本文对特征P的基域F引入适当的Galois群T,讨论p置换模的Green环的Conlon比析在Galois群T作用下的动态,证明了在T作用下p置换模的Green环的不动点集重合于置换模的Green环。