3D‐morphology reconstruction of nanoscale phase‐separation in polymer memory blends

In many organic electronic devices functionality is achieved by blending two or more materials, typically polymers or molecules, with distinctly different optical or electrical properties in a single film. The local scale morphology of such blends is vital for the device performance. Here, a simple approach to study the full 3D morphology of phase‐separated blends, taking advantage of the possibility to selectively dissolve the different components is introduced. This method is applied in combination with AFM to investigate a blend of a semiconducting and ferroelectric polymer typically used as active layer in organic ferroelectric resistive switches. It is found that the blend consists of a ferroelectric matrix with three types of embedded semiconductor domains and a thin wetting layer at the bottom electrode. Statistical analysis of the obtained images excludes the presence of a fourth type of domains. The criteria for the applicability of the presented technique are discussed. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1231–1237     

Light and heat control over secondary structure and amyloid-like fiber formation in an overcrowded-alkene-modified Trp zipper

The external photocontrol over peptide folding, by the incorporation of molecular photoswitches into their structure, provides a powerful tool to study biological processes. However, it is limited so far to switches that exhibit only a rather limited geometrical change upon photoisomerization and that show thermal instability of the photoisomer. Here we describe the use of an overcrowded alkene photoswitch to control a model β-hairpin peptide. This photoresponsive unit undergoes a large conformational change and has two thermally stable isomers which has major influence on the secondary structure and the aggregation of the peptide, permitting the phototriggered formation of amyloid-like fibrils.     

Spectral estimates for saddle point matrices arising in weak constraint four‐dimensional variational data assimilation

We consider the large sparse symmetric linear systems of equations that arise in the solution of weak constraint four‐dimensional variational data assimilation, a method of high interest for numerical weather prediction. These systems can be written as saddle point systems with a 3 × 3 block structure but block eliminations can be performed to reduce them to saddle point systems with a 2 × 2 block structure, or further to symmetric positive definite systems. In this article, we analyse how sensitive the spectra of these matrices are to the number of observations of the underlying dynamical system. We also obtain bounds on the eigenvalues of the matrices. Numerical experiments are used to confirm the theoretical analysis and bounds.     

基于吸收系数的生脉注射液中聚山梨酯80含量测定新方法

聚山梨酯80又名吐温80，为一种亲水型非离子表面活性剂，是食品、保健品和药品中常用的辅料，作为增溶剂和澄清剂广泛用于中药注射剂。近年来，不良反应的发生使得聚山梨酯80的质量和应用愈加受到重视，有研究认为其加入可能引起注射剂不良反应增加。为避免超量使用，有必要对该辅料的投料加以严格控制。中药注射剂中聚山梨酯80的含量测定是当下研究的热点和难点，可以通过分光光度法、分子排阻-蒸发光散射检测法(SEC-ELSD)、液质联用法(LC-MS)直接测定，也可以水解后法经液相色谱-紫外检测法(HPLC-UV)或气相色谱法(GC)间接测定。但由于聚山梨酯80为聚氧乙烯聚合数目不同的混合物、不同厂家生产的聚山梨酯80化学组分及比例存在较大差异，难以采用统一的转换公式或对照品准确定量。此外，中药注射剂的复杂基质造成的假阳性干扰也对定量提出了挑战。为解决以上问题，以生脉注射液为例，提出基于吸收系数的中药注射剂中聚山梨酯80含量测定新方法。优化检测波长、显色剂种类、液液萃取过程振荡和静置时间，在6个不同品牌仪器上测得聚山梨酯80-硫氰酸钴配合物的吸收系数(E1%_{1 cm})为104.23，相对标准偏差(RSD)为2.08%。生脉注射液稀释10倍后，精密量取供试品溶液1.0 mL，精密加入硫氰酸钴溶液10 mL，二氯甲烷20 mL，涡旋振荡3 min。将混合液移至分液漏斗中，静置30 min，取下层二氯甲烷液，将前1 mL弃去，接收约15 mL，在320 nm处测定吸光度，再根据Lambert-Beer定律，利用获得的吸收系数计算得到聚山梨酯80的含量。方法阴性无干扰，精密度和重复性相对标准偏差均低于3%，平均回收率为98.42%。为进一步验证方法的准确性，分别采用吸收系数法和标准曲线法测定了2个厂家的10批生脉注射液，并与实际投料量比较。配对t检验结果表明，当置信度为95%时，两种方法无显著性差异，吸收系数法测得结果与企业生产中聚山梨酯的实际投料量也无显著性差异。研究采用前人未采用的、灵敏度更高的320 nm为检测波长，显著降低了基质干扰，克服了中药注射剂中聚山梨酯80测定结果与实际投料量难以吻合的问题。吸收系数法无需使用对照品，亦不用制备标准曲线，可为中药注射剂中聚山梨酯80的检查标准提供切实可行的解决方案。所建方法灵敏、准确、快速、简便，为含聚山梨酯80制剂的质量控制提供了关键常数及新的思路。     

State of and prospects for XeF(C−A) optically pumped lasers

Experimental and theoretical results are presented on an XeF(C?A) blue-green laser driven by 5-kJ energy. The laser was pumped by a ferrite-induced discharge of 90 cm in length. The output energy of 0.22 J was obtained with a plane-parallel resonator. A program to simulate laser operation has been developed. Numerical results for a wide range of conditions are compared with experiments performed by us and by other authors. It is found that intracavity refractive losses limit laser operation for XeF pressures above 3 torr. The laser efficiency strongly depends on the discharge-to-cavity length ratio. Possible ways to increase the laser power and efficiency are discussed.