Diode-pumped 671 nm laser frequency doubled by CPM LBO

A design of diode-pumped high-efficiency Nd:YVO₄/LBO red laser is reported. Using critical phase-matching (CPM) LBO, 671 nm red laser was obtained from 1342 nm light by intracavity frequency doubling. With an incident pump laser of 800 mW, using type-I and type-II CPM LBO, 97 and 52 mWTEM₀₀ mode red laser outputs were obtained, with optical-to-optical conversion efficiencies of up to 12.1% and 6.5%, respectively.     

Polarized Lidar Reflectance Measurements of Vegetation at Near-Infrared and Green Wavelengths

There is growing interest in the use of lidar for remote sensing of vegetation owing to the emergence of reliable and rugged lasers and highly sensitive detectors. Lidar remote sensing has a distinct advantage over conventional techniques in vegetation remote sensing due to its capability for three-dimensional characterization of vegetative targets. The Multiwavelength Airborne Polarimetric Lidar (MAPL) system was developed primarily for vegetation remote sensing applications from an airborne platform of up to 1,000 -m altitude. The lidar system has full waveform capture and polarimetric measurement capability at two wavelengths in the near-infrared (1064 nm) and the green (532 nm) spectral regions. This study presents preliminary ground-based lidar reflectance measurements on a variety of deciduous and coniferous trees under fully foliated conditions with a view towards tree species discrimination. Variations in the reflectance characteristics of selected deciduous trees under unfoliated and fully foliated conditions were also investigated. Our study reveals distinct differences in the reflectance characteristics of various trees.     

Laser writing techniques for photomask fabrication using a femtosecond laser

Photomasks are the backbone of microfabrication industries. Currently they are fabricated by a lithographic process, which is very expensive and time consuming since it is a multi-step process. These issues can be addressed by fabricating photomasks by direct femtosecond laser writing, which is a single-step process and comparatively cheaper and faster than lithography. In this paper we discuss our investigations on the effect of two types of laser writing techniques, namely front- and rear-side laser writing, with regard to the feature size and the edge quality of a feature. It is proved conclusively that for the patterning of masks, front-side laser writing is a better technique than rear-side laser writing with regard to smaller feature size and better edge quality. Moreover the energy required for front-side laser writing is considerably lower than that for rear-side laser writing. Received: 22 May 2001 / Accepted: 14 September 2001 / Published online: 17 October 2001     

Chemical Constituents of Ligusticum sinensis Oliv.

The new phenylpropanoid diglycoside ligusinenoside A ( 1 ), and the two new 8,4′‐oxyneolignan(‘8‐O‐4′‐neolignan’) diglycosides ligusinenosides B ( 2 ) and C ( 3 ), together with nine known compounds, were isolated from the rhizomes of Ligusticum sinensis Oliv. The structures of 1 – 3 were elucidated on the basis of spectroscopic analyses.     

A power-law distribution for tenure lengths of sports managers

We show that the tenure lengths for managers of sport teams follow a power law distribution with an exponent between 2 and 3. We develop a simple theoretical model which replicates this result. The model demonstrates that the empirical phenomenon can be understood as the macroscopic outcome of pairwise interactions among managers in a league, threshold effects in managerial performance evaluation, competitive market forces, and luck at the microscopic level.     

Controlled/living polymerization of 2‐(diethylamino)ethyl methacrylate and its block copolymer with tert‐butyl methacrylate by atom transfer radical polymerization

Polymerization of 2‐(diethylamino)ethyl methacrylate (DEAEMA) via homogeneous atom transfer radical polymerization under various reaction conditions is described. The effects of the initiators and solvents were examined. With 1,1,4,7,10,10‐hexamethyl triethylenetetramine/copper(I) chloride/p‐toluenesulfonyl chloride as the ligand/catalyst/initiator system in methanol, poly(DEAEMA) with a polydispersity index as low as 1.07 was synthesized. Kinetic studies demonstrated the polymerization was very well controlled and exhibited the living characteristic of the process. Well‐defined block copolymers of DEAEMA and tert‐butyl methacrylate (tBMA) were successfully synthesized. The copolymers could be synthesized with equally good results by starting with either p(DEAEMA) or p(tBMA) as the macroinitiators. However, only the macroinitiators terminated with chlorine should be used. The corresponding macroinitiators with bromine as a transferable group did not yield well‐defined copolymers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2688–2695, 2003     

On the validity of the amphoteric-defect model in gallium arsenide and a criterion for Fermi-level pinning by defects

Using the theoretically calculated point-defect total-energy values of Baraff and Schlüter in GaAs, anamphoteric-defect model has been proposed by Walukiewicz to explain a large number of experimental results. The suggested amphoteric-defect system consists of two point-defect species capable of transforming into each other: the doubly negatively charged Ga vacancyV _Ga ^2– and the triply positively charged defect complex (AS_Ga+V _As)³⁺, with As_Ga being the antisite defect of an As atom occupying a Ga site andV _As being an As vacancy. When present in sufficiently high concentrations, the amphoteric defect systemV _Ga ^2– /(As_Ga+V _As)³⁺ is supposed to be able to pin the GaAs Fermi level at approximately theE _v +0.6 eV level position, which requires that the net free energy of theV _Ga/(As_Ga+V _As) defect system to be minimum at the same Fermi-level position. We have carried out a quantitative study of the net energy of this defect system in accordance with the individual point-defect total-energy results of Baraff and Schlüter, and found that the minimum net defect-system-energy position is located at about theE _v +1.2 eV level position instead of the neededE _v +0.6 eV position. Therefore, the validity of the amphoteric-defect model is in doubt. We have proposed a simple criterion for determining the Fermi-level pinning position in the deeper part of the GaAs band gap due to two oppositely charged point-defect species, which should be useful in the future.     

Simulation of island aggregation influenced by substrate temperature, incidence kinetic energy and intensity in pulsed laser deposition

Using kinetic Monte Carlo method, we have simulated a pulsed energetic growth process in pulsed laser deposition. During the growth of film, substrate temperature mainly influences upon film morphology by directly enhancing the adatom mobility through the temperature-dependent thermal vibration. By contrast, the effect of incidence kinetic energy on film growth is complex resulting from the collisions between the incident particles and the adatoms. The results show that improving incident kinetic energy cannot significantly accelerate the migration rate of adatom but change surface microstructure and promote single adatom formation resulting in more island aggregation density. Moreover, since pulse-influx characterizes pulsed laser deposition, the intensity per pulse contributes to the evolvement of nucleation density and the results illustrate that a general scaling law different from ordinary power law still exists in energetic growth of pulsed laser deposition.