Mechanical mixtures of Me (Ni, Pd) Ce oxides and silica-supported heteropolyacids: Role and optimal concentration of each active species in n-hexane isomerization

Catalytic properties of silica-supported heteropolyacids (HPA) in a mechanical mixture with reduced Me-Ce oxides (Me = Ni, Pd) in n-hexane isomerization are studied. The role of each component of the mixed oxides (Ce and, typically, Ni and Pd) and their optimum content has been illuminated: cerium is not only beneficial for eliminating or preventing coke deposition but is also effective for maintaining the Keggin structure of the highly-organized HPA during the reaction and probably allows a better dispersion of the second metal species. Nickel and palladium, present as Ni⁰ and Pd⁰, reinforce the activation of the alkane, which is difficult to obtain by means of a direct attack by an acid, and, thus, enhance noticeably the activity of the catalyst. The best mechanical mixtures are obtained with 30–70 wt % NiCeO-HPW/SiO₂ and 50–50 wt % Pd_0.1CeO-HPW/SiO₂. These mixtures have the highest efficiency for a Ni/(Ni + W) atomic ratio of 0.66 and a Pd/(Pd + W) ratio of 0.40, respectively. Finally, the conversion of n-hexane is in the order HPW > HSiW > HBW, which seems to be consistent with the order of their acid strength as per the literature, but the isomerization selectivity appears to be slightly higher on HSiW. Published in Russian in Kinetika i Kataliz, 2006, Vol. 47, No. 1, pp. 24–28. The text was submitted by the authors in English.     

Synthesis and gas barrier characterization of poly(ethylene isophthalate)

Poly(ethylene isophthalate) (PEI) was synthesized for this research with essentially a condensation polymerization of isophthalic acid and ethylene glycol catalyzed by zinc acetate and antimony trioxide. Several samples were obtained, and their characteristics were observed and compared with poly(ethylene terephthalate) (PET). The synthesized PEI samples were chemically identified by ¹H NMR. Thermal analysis with differential scanning calorimetry (DSC) yielded results that indicate the samples were primarily amorphous, with a glass‐transition temperature of 55–60 °C. Molecular weights of these PEI samples were also obtained through intrinsic viscosity measurements (Mark–Houwink equation). Molecular weights varied with conditions of the polymerization, and the highest molecular weight achieved was 21,000 g/mol. Finally, the diffusion coefficient, solubility, and permeability of CO₂ gas in PEI were measured and found to be substantially lower than in PET, as anticipated from their isomeric chemical structures. This is because in PET the phenyl rings are substituted in the para (1,4) positions, which allows for their facile flipping, effectively permitting gases to pass through. However, the meta‐substituted phenyl rings in PEI do not permit such ring flipping, and thus PEI may be more suitable for barrier applications. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4247–4254, 2004     

“Slow” active control of combustion instabilities by modification of liquid fuel spray properties

This paper describes an experimental investigation of the feasibility of using “slow” active control approaches, which “instantaneously” change liquid fuel spray properties, to suppress combustion instabilities. The objective of this control approach was to break up the feedback between the combustion process heat release and combustor pressure oscillations that drive the instability by changing the characteristics of the combustion process (e.g., the characteristic combustion time). To demonstrate the feasibility of such control, this study used a proprietary fuel injector (Nanomiser^TM), which can vary its fuel spray properties, to investigate the dependence of acoustics–combustion process coupling, i.e., the driving of combustion instabilities, upon the fuel spray properties. This study showed that by changing the spray characteristics it is possible to significantly damp combustion instabilities. Furthermore, using combustion zone chemiluminescence distributions, which were obtained by Abel’s deconvolution synchronized with measured acoustic data, it has been shown that the instabilities were mostly driven midway between the combustor centerline and wall, a short distance downstream from the flame holder, where the mean axial flow velocity is approximately zero in the vortex near the flame holder. The results of this study strongly suggest that a “slow” active control system that employs controllable fuel injectors could be effectively used to prevent the onset of detrimental combustion instabilities.     

Dynamic response of permalloy/Cu/Co magnetoresistive sandwiches

The dynamic response of trilayer magnetoresistive permalloy/Cu/Co films was studied by high-frequency permeability spectra measurements. The resonance frequency is shown to depend on the interlayer copper thickness. This dependence is related to exchange coupling between permalloy and cobalt and the interaction field is estimated using the Landau–Lifschitz–Gilbert model.     

Optimal stopping problems by two or more decision makers: a survey

A review of the optimal stopping problem with more than a single decision maker (DM) is presented in this paper. We classify the existing literature according to the arrival of the offers, the utility of the DMs, the length of the sequence of offers, the nature of the game and the number of offers to be selected. We enumerate various definitions for this problem and describe some dynamic approaches. Fouad Ben Abdelaziz is on leave from the Institut Superieur de Gestion, University of Tunis, Tunisia e-mail: foued.benabdelaz@isg.run.tn.     

1H and13C nuclear magnetic relaxation and local dynamics of lysozyme and synthetic polypeptides

The combined analysis of¹H and¹³C NMR relaxation data in solid lysozyme and some typical homopolypeptides was carried out by using “model-free” approach. Three types of relaxation transitions (γ’, γ and β) were revealed in the temperature range investigated. The microdynamical parameters of these motions were determined. From the comparison of these parameters with those of selected synthetic polymers it follows that the molecular motions in proteins and synthetic polymers are of the same nature. All these motions show pronounced anisotropic character. In the investigated temperature range no molecular motions corresponding to α-relaxation (liquid-like) transition were revealed. The hydration effects on parameters of the motions in proteins were considered. The most pronounced effect takes place for β-transition. The effect of Brownian rotation of protein molecule in solution on measured correlation function of local motions was also discussed.