Some properties of the bilevel programming problem

The purpose of this paper is to elaborate on the difficulties accompanying the development of efficient algorithms for solving the bilevel programming problem (BLPP). We begin with a pair of examples showing that, even under the best of circumstances, solutions may not exist. This is followed by a proof that the BLPP is NP-hard.This work was partially supported by a grant from the Advanced Research Program of the Texas Higher Education Coordinating Board.     

Coulometric titration of copper(II) with electro-generated chromium(II)

The current efficiency for the electrogeneration of chromium(II) for use as a coulometric titrant was studied for several supporting electrolytes. With a mercury cathode and a 0.1 M chromic sulfate-0.1 M potassium chloride medium, 0.8 to 2.8 mg of copper (II) in 110 ml of solution can be titrated using potentiometric end-point detection.     

Individually addressable submicron scale light-emitting devices based on electroluminescence of solid Ru(bpy)3(ClO4)2 films

A submicron light-emitting device (LED) was fabricated from lithographically fabricated parallel indium-tin oxide (ITO) finger electrodes (0.9 mum wide) separated by a 1.1 mum gap. A single layer of an amorphous (a) Ru(bpy)3(ClO4)2 film ( approximately 100 nm thick) was spin-coated on the electrode array. Ga:In or carbon paste was employed as a liftable upper contact electrode. Films ( approximately 1.5 mum thick) of single-crystal Ru(bpy)3(ClO4)2 (xyl) between two ITO electrodes in a sandwich cell were also prepared and produce electroluminescence. As with larger cells of this type, the high-resolution electroluminescence produced showed a high external efficiency ( approximately 3.4%), a low turn-on voltage (2.3 V), and reasonable stability. The single-crystal cells also behaved as photovoltaic devices and a short-circuit photocurrent was observed when they were irradiated without a bias voltage.     

Fractionation of casein hydrolysates using polysulfone ultrafiltration hollow fiber membranes

The objective of this study was to characterize the fractionation profile of casein hydrolysates obtained with polysulfone hollow fiber ultrafiltration membranes. The two-step ultrafiltration process developed by Turgeon and Gauthier [J. Food Sci., 55 (1990) 106] was used: a caseinate solution was submitted to proteolysis with chymotrypsin or trypsin, and the reaction mixture (RM) was subsequently ultrafiltered using a 30 kDa (MWCO) hollow-fiber polysulfone membrane. The total hydrolysate permeating from this first step was further fractionated using a 1 kDa (MWCO) membrane, producing the mixture of polypeptides (retentate) and the amino acid fraction (permeate). The effect of enzyme specificity and of membrane retentivitiy on the total composition (total nitrogen, fat, lactose, minerals) and amino acid profile of the fractions was studied. The overall composition of the fractions was not significantly affected by the nature of the enzyme but the degree of hydrolysis and the molecular weight distribution profile analyses showed a marked effect of the enzyme specificity, with trypsin giving a larger proportion of small peptides (< 200 Da) in the mixture of polypeptides. Amino acid profile analyses provided useful information on the phenomena governing the fractionation of amino acids with a polysulfone membrane: (1) the target amino acids of the enzyme are concentrated in the permeate as a result of their presence in all peptides produced by hydrolysis, (2) polar amino acids are retained by the membrane, (3) non-polar amino acids are not selectively rejected by the membrane. Our results suggest that the charge/hydrophobicity balance of the peptides produced is the predominant factor determining the fractionation of casein hydrolysates.     

Pd-Co-Mo electrocatalyst for the oxygen reduction reaction in proton exchange membrane fuel cells

The catalytic activity of carbon supported Pd-Co-Mo for the oxygen reduction reaction (ORR) in a single cell proton exchange membrane fuel cell (PEMFC) has been investigated at 60 degrees C and compared with data from commercial Pt catalyst and our previously reported Pd-Co-Au and Pd-Ti catalysts. The Pd-Co-Mo catalyst with a Pd:Co:Mo atomic ratio of 70:20:10 exhibits slightly higher catalytic activity like the Pd-Co-Au catalyst than the commercial Pt catalyst, but with excellent chemical stability unlike the Pd-Co-Au catalyst. The Pd-Co-Mo catalyst also exhibits better tolerance to methanol poisoning than Pt. Investigation of the catalytic activity of the Pd-Co-Mo system with varying composition and heat treatment temperature reveals that a Pd:Co:Mo atomic ratio of 70:20:10 with a heat treatment temperature of 500 degrees C exhibits the highest catalytic activity. Although the degree of alloying increases with increasing temperature from 500 to 900 degrees C as indicated by the X-ray diffraction data, the catalytic activity decreases due to an increase in particle size and a decrease in surface area.     

The application of scanning electrochemical microscopy to the discovery of Pd–W electrocatalysts for the oxygen reduction reaction that demonstrate high activity, stability, and methanol tolerance

An array of Pd–W alloys was fabricated, and the electrocatalytic activity of the alloys for the oxygen reduction reaction (ORR) in acidic media was screened by scanning electrochemical microscopy. The Pd_0.7W_0.3 showed the highest activity for the ORR, close to that for Pd_0.8Co_0.2 and Pt. A Pd–W electrocatalyst loaded on carbon black was formed by the NaBH₄-reduction method, exhibiting high activity and stability, suggesting that it is a good candidate for the proton exchange membrane fuel cell cathode.