EXISTENCE OF PERIODIC SOLUTION OF A NEURONIC EQUATION

１ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｂｒａｉｎｏｆｍａｎｋｉｎｄｈａｓｍａｎｙｃｏｇｎｉｔｉｖｅｆｕｎｃｔｉｏｎｓｓｕｃｈａｓｌｅａｒｎｉｎｇ，ａｓｏｃｉａｔｉｏｎａｎｄｏｐｔｉｍｉｚａｔｉｏｎｅｔｃ．．Ｔｈｅｎｅｕｒｏｎｉｓｔｈｅｍｏｓｔｆｏｕｎｄａｍ...     

Synthesis and characterization of white‐light‐emitting polyfluorenes containing orange phosphorescent moieties in the side chain

Two orange phosphorescent iridium complex monomers, 9‐hexyl‐9‐(iridium (III)bis(2‐(4′‐fluorophenyl)‐4‐phenylquinoline‐N,C^2′)(tetradecanedionate‐11,13))‐2,7‐dibromofluorene (Br‐PIr) and 9‐hexyl‐9‐(iridium(III)bis(2‐(4′‐fluorophenyl)‐4‐methylquinoline‐N,C^2′)(tetradecanedionate‐11,13))‐2,7‐dibromofluorene (Br‐MIr), were successfully synthesized. The Suzuki polycondensation of 2,7‐bis(trimethylene boronate)‐9,9‐dioctylfluorene with 2,7‐dibromo‐9,9‐dioctylfluorene and Br‐PIr or Br‐MIr afforded two series of copolymers, PIrPFs and MIrPFs, in good yields, in which the concentrations of the phosphorescent moieties were kept small (0.5–3 mol % feed ratio) to realize incomplete energy transfer. The photoluminescence (PL) of the copolymers showed blue‐ and orange‐emission peaks. A white‐light‐emitting diode with a configuration of indium tin oxide/poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate)/PIr05PF (0.5 mol % feed ratio of Br‐PIr)/Ca/Al exhibited a luminous efficiency of 4.49 cd/A and a power efficiency of 2.35 lm/W at 6.0 V with Commission Internationale de L'Eclairage (CIE) coordinates of (0.46, 0.33). The CIE coordinates were improved to (0.34, 0.33) when copolymer MIr10PF (1.0 mol % feed ratio of Br‐MIr) was employed as the white‐emissive layer. The strong orange emission in the electroluminescence spectra in comparison with PL for these kinds of polymers was attributed to the additional contribution of charge trapping in the phosphorescent dopants. © 2007 Wiley Periodicals, Inc. JPolym Sci Part A: Polym Chem 45: 1746–1757, 2007     

环丙烯基自由基H-F力的abinitio研究

环丙烯基自由基是我们熟知的最小环状化合物。人们用不同的理论方法对它进行了预测。一般认为平面构型(D_(3h)对称性)要经受Jahn-Teller畸变以消除π轨道的简并性,畸变过程如图1所示。我们研究了此类三元环自由基引起的键的“弯曲效应”,以便对这类“张力”分子的成键特性及Jahn-Teller畸变、芳香性等给出某些理论信息,探讨其理论计算结果所能阐明的问题。     

聚甲醛自然老化的SEM研究

对户外曝晒3～36个月的聚甲醛(POM)老化形态进行了研究,讨论了老化层厚度,裂纹宽度、裂纹深度及断口形态与老化时间的关系。结果表明:POM的老化导致了材料内部结构由韧性变成脆性而几乎完全丧失物理机械性能。     

MH—Ni电池封口化成及其性能

在硼氢化钾碱性溶液中对金属氢化物（ＭＨ）电极的表面进行化学还原处理，提高了ＭＨ电极的放电容量、活化性能和电催化活性．用其为负极组装的ＡＡ型ＭＨ－Ｎｉ电池进行了封口化成，电池放电容量达到１１５０ｍＡｈ，５Ｃ下电池的放电容量达到０．２Ｃ下容量的８０％以上，电池在１Ｃ１００％ＤＯＤ（放电深度）充放电条件下，循环寿命由原来的１００次左右提高到２００次以上     

Triple Positive Solutions of Boundary Value Problems for High-order Fractional Differential Equation at Resonance with Singularities

In this paper, we investigate the existence of triple positive solutions of boundary value problems for high-order fractional differential equation at resonance with singularities by using the fixed point index theory and the Leggett-Williams theorem. The spectral theory and some new height functions are also employed to establish the existence of triple positive solutions. The nonlinearity involved is arbitrary fractional derivative, and permits singularity.     

The radioisotopic battery based on radio-voltaic effect

The radio-voltaic effect is investigated to be applied radioisotopic batteries in this work. The collection rates of the electron-hole pairs are 94 percent for the alpha particles emitted by²³⁹Pu source and 65 percent for the beta particles emitted by⁹⁰Sr-⁹⁰Y source. The maximum energy conversion efficiency got by the silicon element is about 16%. A prototype radioisotopic battery with¹⁴⁷Pm beta sources is constructed. Its maximum short-circuit current and off voltage are about 2 A and 190 mV respectively. The experimental data suggest that the life of the prototype battery may be more than three years.     

减压蜡油缓和加氢裂化催化剂酸性研究

用热重原位氨吸附－程序升温脱附及氨吸附－差热法考察了含分子筛缓和加氢裂化催化剂的载体、活性金属组分及催化剂本身的酸性。发现载体的总酸量是其分子筛含量的线性函数。载体担载上Ｎｉ、Ｗ活性组分后，可不同程度的引起催化剂的酸性变化。催化剂中分子筛含量增加除提高其加氢裂化活性外，还可增加它的ＶＧＯ加氢脱氮及加氢脱芳烃的活性，但会引起中馏份选择性的下降。催化剂的酸性可通过载体的分子筛含量、类型及分子筛改性加以调节。     

Dense Sphene-type Solid Electrolyte Through Rapid Sintering for Solid-state Lithium Metal Battery

The sphene-type solid electrolyte with high ionic conductivity has been designed for solid-state lithium metal battery. However, the practical applications of solid electrolytes are still suffered by the low relative density and long sintering time of tens of hours with large energy consumption. Here, we introduced the spark plasma sintering technology for fabricating the sphene-type Li_1.125Ta_0.875Zr_0.125SiO₅ solid electrolyte. The dense electrolyte pellet with high relative density of ca. 97.4% and ionic conductivity of ca. 1.44×10^-5 S/cm at 30℃ can be obtained by spark plasma sintering process within the extremely short time of only ca. 0.1 h. Also the solid electrolyte provides stable electrochemical window of ca. 6.0 V(vs. Li⁺/Li) and high electrochemical interface stability toward Li metal anode. With the enhanced interfacial contacts between electrodes and electrolyte pellet by the in-situ formed polymer electrolyte, the solid-state lithium metal battery with LiFePO₄ cathode can deliver the initial discharge capacity of ca. 154 mA·h/g at 0.1 C and the reversible capacity of ca. 132 mA·h/g after 70 cycles with high Coulombic efficiency of 99.5% at 55℃. Therefore, this study demonstrates a rapid and energy efficient sintering strategy for fabricating the solid electrolyte with dense structure and high ionic conductivity that can be practically applied in solid-state lithium metal batteries with high energy densities and safeties.     

Challenge and Solution of Characterizing Glass Transition Temperature for Conjugated Polymers by Differential Scanning Calorimetry

Thermomechanical properties of polymers highly depend on their glass transition temperature (T _g). Differential scanning calorimetry (DSC) is commonly used to measure T _g of polymers. However, many conjugated polymers (CPs), especially donor–acceptor CPs (D–A CPs), do not show a clear glass transition when measured by conventional DSC using simple heat and cool scan. In this work, we discuss the origin of the difficulty for measuring T _g in such type of polymers. The changes in specific heat capacity (Δc _p) at T _g were accurately probed for a series of CPs by DSC. The results showed a significant decrease in Δc _p from flexible polymer (0.28 J g^?1 K^?1 for polystyrene) to rigid CPs (10^?3 J g^?1 K^?1 for a naphthalene diimide‐based D–A CP). When a conjugation breaker unit (flexible unit) is added to the D–A CPs, we observed restoration of the Δc _p at T _g by a factor of 10, confirming that backbone rigidity reduces the Δc _p. Additionally, an increase in the crystalline fraction of the CPs further reduces Δc _p. We conclude that the difficulties of determining T _g for CPs using DSC are mainly due to rigid backbone and semicrystalline nature. We also demonstrate that physical aging can be used on DSC to help locate and confirm the glass transition for D‐A CPs with weak transition signals. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1635–1644