Characterisation of anodic oxide films on zirconium formed in sulphuric acid: XPS and corrosion resistance investigations

Present work describes investigations of a two-step process consisting of galvanostatic anodising in a 1 M H₂SO₄ solution at 100 mA cm⁻² up to the limiting voltages of 20, 60, 80, 100 and 120 V, directly after which potentiostatic regime was employed and the current was allowed to drop. The total treatment time (5 min) was held constant for all samples. The treatment was carried out to improve the corrosion resistance of zirconium in physiological conditions, which was determined by electrochemical evaluation in Ringer’s solution. XPS studies revealed that after anodising sulphur was incorporated into the oxide film in the form of sulphated zirconia. The maximum content of sulphate in the oxide layer was observed after anodising at 80 V. Anodising at higher voltages resulted in formation of coatings with decreasing amount of sulphur. It was found that there is a strong correlation between the sulphur content in the oxide layers and the measured corrosion current density. On the other hand, the pitting corrosion resistance seemed to be unaffected by the presence of S and it was improving with the increasing limiting voltage of the treatment.

     

Synthesis and characterization of a Ni nanoparticle stabilized on Ionic liquid‐functionalized magnetic Silica nanoparticles for tandem oxidative reaction of primary alcohols

In this research, preparation of the magnetic nanoparticle, coating by a silica shell using (3‐aminopropyl) triethoxysilane and synthesis of a novel sulfonic acid‐substituted imidazolium‐based ionic liquid onto the surface of these particles via a multi‐component reaction, is described. The functionalized nanoparticles was loaded by Ni nanoparticles and characterized by means of techniques such as XRD, FTIR, SEM, EDX, TEM, TGA and ICP‐OES. The nanostructures have spherical shapes that ranged in size from 80 to 100 nm. The catalytic activity of these nanoparticles was tested in aerobic oxidation of primary alcohols that showed good performance in the wide range of primary alcohols in water at mild reaction conditions. As a second step of this work, the tandem oxidative synthesis of alkylacrylonitriles and bisindolylmethanes were investigated using primary alcohols under oxidation conditions. This catalyst system can be recovered using external magnet and reused for five consecutive cycles without significantly less of its activity.     

A computational investigation of carbon-doped beryllium monoxide nanotubes

To investigate the influence of C-doping on the electrostatic structure properties in the frame work of density functional theory (DFT), we considered beryllium monoxide nanotubes (BeONTs), consisting of 60 Be and 60 O atoms. Full geometry optimizations are performed for all structures, i.e., all atoms are allowed to relax. Afterwards, the chemical shielding (CS) tensors are calculated for Be-9, O-17 and C-13 nuclei in the C-doped forms and also pristine models of the (10, 0) zigzag and (5, 5) armchair BeONTs. Formation energies indicate that C-doping of Be atom (CBe form) could be more favorable than C-doping of O atom (CO form) in both zigzag and armchair BeONTs. Gap energies and dipole moments detected the effects of dopant in the (5, 5) armchair models; however, those parameters did not indicate any significant changes in the C-doped (10, 0) zigzag BeONT models. The results show that the CS values for the Be and O atoms-contributed to the Be-C bonds or those atoms close to the C-doped region-in the CO form of BeONTs (zigzag and armchair) are changed. The same values only for the O atoms-contributed to the O-C bonds- in the CBe form of BeONTs (zigzag and armchair) are changed.     

Multivariate linear regression with missing values

This contribution presents and discusses an efficient algorithm for multivariate linear regression analysis of data sets with missing values. The algorithm is based on the insight that multivariate linear regression can be formulated as a set of individual univariate linear regressions. All available information is used and the calculations are explicit. The only restriction is that the independent variable matrix has to be non-singular. There is no need for imputation of interpolated or otherwise guessed values which require subsequent iterative refinement.     

Towards insight into properties and stabilities of complexes of ozone with CO2, CS2 and SCO species

The MP2 method in combination with the aug-cc-pVXZ (X = D and T) basis set has been carried out to examine the complexes between O₃ and isostructure species of CO₂, CS₂ and SCO. Two, two and four minima have been located on the potential energy surfaces of O₃–CO₂, O₃–CS₂ and O₃–SCO complexes, respectively. The results reveal that the stabilization of complexes should be in the order O₃–CS₂ > O₃–SCO > O₃–CO₂.     

Electropolymerized coatings of poly(o‐anisidine) and poly(o‐anisidine)‐TiO2 nanocomposite on aluminum alloy 3004 by using the galvanostatic method and their corrosion protection performance

Poly(o‐anisidine) (POA) and poly(o‐anisidine)‐TiO₂ (POA‐TiO₂) nanocomposite coatings on aluminum alloy 3004 (AA3004) have been investigated by using the galvanostatic method. The electrosynthesized coatings were characterized by FT ‐ IR spectroscopy, XRD, SEM ‐ EDX and SEM. The corrosion protection performance of POA and POA‐TiO₂ nanocomposite coatings was investigated in the 3.5% NaCl solution by using potentiodynamic polarization technique and electrochemical impedance spectroscopy. The results show that the corrosion rate of the nanocomposite coatings is about 900 times lower than the bare AA3004 under optimal conditions. Copyright © 2013 John Wiley & Sons, Ltd.     

Novel Foaming-Agent Free Insulating Geopolymer Based on Industrial Fly Ash and Rice Husk

This study highlights the synthesis of a new thermal insulating geopolymer based on the alkaline activation of fly ashes. A porous geopolymer material can be prepared without the addition of a foaming agent, using high ratio solution/ashes (activating solutions used are water, sodium or potassium hydroxide). In order to increase the porosity of the material and to make it more ecological, rice husks are incorporated into the formulation. The geopolymer materials were prepared at room temperature and dried at moderate temperature (105 °C) by a simple procedure. The microstructural characteristics of these new porous geopolymers were assessed by optical microscopy, X-ray diffraction (XRD), thermogravimetric analysis (TGA) and X-ray fluorescence (XRF). Infrared spectroscopy (FTIR) was used to confirm the geopolymerisation. The effect of the ratio solution/ashes and the percentage of the rice husk addition on thermal and mechanical analysis was evaluated. An insulating material for a solution/ashes ratio of 0.9 and a rice husk content of 15% having a λ value of 0.087 W/(m·K), a porosity of 61.4% and an Rc value of 0.1 MPa was successfully prepared.