A NOTE ON FULLER'S THEOREM

In 1972, Fuller proved that a complete additive subeategory _RC of R-Mod isequivalent to amodule category ⊿-Mod if and only if _RC=Gen(_RU)for some quasiprogenerator _RU and ⊿≌End _RU canonically. In this note the author gives a characterization of _RC which makes _RU a projective R-module in the case when R is a right perfect ring with identity, and shows that R-Mod is the unique complete additive subcategory of R-Mod which is equivalent to R-Mod for a left Artinian ring R.     

A high-resolution MAS NMR study on the potential catalysts Mo/HBeta for olefin metathesis: The interaction of Mo species with HBeta zeolite

The interfacial interaction of Mo species with the HBeta zeolite was studied by multinuclear MAS NMR, XRD and N₂ adsorption. As proved by the quantitative ²⁷Al MAS NMR, this interaction is so strong as to dealuminate the framework of HBeta, and leads to a new peak appearing at −14 ppm, which indicates the formation of crystalline Al₂(MoO₄)₃. This can also be detected by XRD measurements when the Mo loading is as high as 9.0 wt.%. The corresponding quantitative ²⁹Si and ¹H MAS NMR spectra show that the amount of silanols and Brønsted acidic sites decrease obviously with increasing Mo loading. This also reveals an interaction between Mo species and HBeta support through an oxygen bridge resulting from condensation with the hydroxyls on the support. At higher Mo loadings, the interaction is so strong that it results in an extraction of aluminum from the zeolite framework, and subsequently appearance of Al₂(MoO₄)₃ and loss of Brønsted acidic sites. These can be correlated to the low catalytic activity of Mo/HBeta in metathesis of ethylene and 2-butylene to propylene.     

Comparison of 6Mo/MCM-22 and 6Mo/ZSM-5 in the MDA process

A comparison of methane dehydroaromatization (MDA) on 6Mo/MCM-22 and 6Mo/ZSM-5 was carried out using a gas mixture of 90%CH₄, 2%CO₂ and 8%Ar as the feed. The results indicate that the stability of 6Mo/MCM-22 is better than that of 6Mo/ZSM-5. A detailed study reveals that the ability for coke accommodation and the retention of the shape selectivity for aromatics formation is responsible for the stability of a MDA catalyst. This revised version was published online in August 2006 with corrections to the Cover Date.     

甲烷在Ni表面及La薄膜上激活解离化学吸附

利用分子束技术改变甲烷的平动能E_k来研究E_k及其法向分量E_n对甲烷在Ni表面及La薄膜上激活解离吸附的影响。对CH_4/Ni及CH_4/La系统, 当甲烷的平动能E_k分别低于58.5 kJ·mol~(-1)及52.3 kJ·mol~(-1)时, 没观察到甲烷的解离吸附。当甲烷的平动能超过此阈值时, 即对CH_4/Ni系统, 当Ek=58.5增至63.8 kJ·mol~(-1)时, 初始沾着几率s_0由0至0.54线性增加; 对CH_4/La系统, 当E_k=52.3增至63.8 kJ·mol~(-1)时, S_0由0至0.49线性增加。这些结果表明, 两个系统的化学吸附是不经过前趋态的直接化学吸附。最后求出CH_4/Ni, CH_4/La系统的表观活化能分别为46.8 kJ·mol~(-1)和38.1 kJ·mol~(-1)。     

液相苯与稀乙烯变相催化分离生成乙苯的化学平衡、物料平衡和热量平衡计算

 提出了液相苯和稀乙烯变相催化分离制乙苯的反应示意图,对该烷基化反应部分的化学平衡、物料平衡和热量平衡进行了计算. 在温度185 ℃, 压力2.0 MPa, 乙烯1 mol/h, 氮4 mol/h, 新鲜苯3 mol/h的条件下, 烷基化反应后的绝热温升为175.6 ℃. 计算的温升、乙烯转化率和乙苯选择性结果与实验结果基本相符. 从反应段上部补充的35 ℃的新鲜苯与反应段流出的202.6 ℃气体进行热交换后,体系温度达到185.9 ℃, 稍高于反应温度(185 ℃). 但从反应段下部进入的35 ℃的稀乙烯与反应段流出的202.6 ℃的液体混合进行热交换时,由于稀乙烯使液体产物汽化,导致体系温度大幅度降低,平衡时体系温度仅为153.5 ℃, 远低于所要求的反应温度. 计算结果表明,需给体系提供91.5 kJ的热,或者将稀乙烯加热至523 ℃, 混合后体系平衡温度才能达到185 ℃.     

聚酰亚胺研究新进展

聚酰亚胺（PI）是一类重要的高性能聚合物,广泛应用在航空航天、微电子、汽车、石油等高科技领域。由于其结构上的可设计性,世界上越来越多的研究者投入到这类高技术材料的研究开发中。本文分别从可溶性PI的分子设计与合成、功能性PI的合成与用途、PI绿色合成方法、PI纳米复合材料的制备4个方面综述了近年来PI的研究热点和新进展,为了解聚酰亚胺的研究提供了有价值的信息。     

Acidity effects of Hβ zeolite on olefin alkylation of thiophenic sulfur in gasoline

Olefin alkylation of thiophenic sulfur process was carried out in model gasoline, using Hβ zeolites with different Si/Al2 ratios as catalysts. In particular, the influence of acid properties of Hβ zeolites on its catalytic ability for the thiophene alkylation, xylene alkylation and hexene oligomerization was investigated. The results showed that the acidity of the Hβ zeolite was increased with the decrease of Si/Al2 ratio, but its catalytic ability was not always increased. In fact, it reached the maximal catalytic ability at Si/Al2 ratio of 66, and under the reaction conditions of 60 ℃, 1.5 MPa, WHSV 3.0 h^-1 and time on stream 2 h. At the ratio, the conversion of thiophene, xylene, and oligomerized hexene were 96.6%, 2.7% and 2.8%, respectively. An optimal Si/Al2 ratio exists for the catalytic performance of Hβ zeolite. By investigating the coke deposition of the used Hβ zeolite catalysts, it has been found that the optimal Si/Al2 ratio is attributed to the combined effect of the carbocation activation capability and the hydrogen transformation capability of the Hβ zeolite catalyst.     

高效钼基催化剂上正丁烯自歧化生成乙烯和己烯（英文）

烯烃歧化反应(又称烯烃复分解反应)是两分子烯烃通过碳-碳键断裂重排生成新烯烃分子的反应,自1964年Phillips公司的Banks等发现以来,引起了研究者的广泛关注,且在均相催化体系的发展尤为迅速;与此同时,多相烯烃歧化催化剂因其在分离简单、可循环再生利用方面的优势而在工业界崭露锋芒.多相烯烃歧化催化剂通常由活性金属组分(Re,Mo,W)分散到大比表面积的多孔载体制备而成.多相催化剂上烯烃歧化反应主要集中在乙烯和2-丁烯反歧化制丙烯反应,其中WO_3/SiO_2催化剂先后应用于Phillips公司的Triolefin Process和ABB Lummus公司的OCT工艺,低温Re系催化剂被法国石油研究院应用到Meta-4歧化工艺.同时丙烯歧化也是研究最多的反应,多数情况下被用作探针反应来研究催化剂的性能.烯烃歧化反应可以根据市场需求灵活调变产物分布,为碳四烃类的高效转化利用提供很好的途径.受国内拉动内需的政策及下游应用行业强劲需求的影响,中国液化石油气的产量逐年递增.2014年我国液化气产量约为2550万吨,其中仅有39%左右用于碳四深加工,大部分当做燃料直接烧掉.从组成来看,液化气中烯烃含量在40%-50%,可以转化为高附加值的乙烯和丙烯进一步利用.本文重点开发了一条从1-丁烯出发生产乙烯/己烯的反应路线及对应的催化剂.首先从热力学角度分析了碳四歧化反应网络中各反应路径发生的难易程度.在此基础上,以Mo/Al_2O_3为催化剂考察了Mo负载量和反应条件对产物分布的影响-.在优化的6Mo/Al_2O_3催化剂上,80°C,1.0 MPa和丁烯空速3 h1的条件下,产物中乙烯和己烯的摩尔选择性超过85%,并且在48 h内保持良好的反应稳定性.为了进一步探究催化剂结构与反应性能的关系,系统考察了催化剂载体差异对Mo物种状态和反应性能的影响.借助N2吸附,NH_3-TPD,Py-IR,H_2-TPR,UV-Vis和HRTEM等表征手段,发现催化剂反应活性与其酸密度直接相关.催化剂酸量越大,丁烯转化率越高,但副反应越多;载体适宜的酸量和较大的比表面积更有利于钼物种的分散和四配位钼物种的形成,促进目标1-丁烯自歧化制乙烯/己烯反应的发生.     

无粘结剂ZSM-11催化剂上异丁烯直接胺化生成叔丁胺

叔丁胺是一种重要的化工原料和中间体,广泛应用于制备橡胶促进剂、医药、农药和着色剂等下游产品.异丁烯在分子筛催化剂上直接胺化生产叔丁胺是一个经济环保过程,其中ZSM-5和BEA分子筛的催化性能优于其它系列分子筛.ZSM-11与ZSM-5分子筛具有相似的孔道结构,我们以前的实验结果表明,与ZSM-5相比,ZSM-11表现出更优越的芳构化反应性能,在干气中乙烯低温芳构化方面也有明显优势.在此基础上,我们进行无粘结剂ZSM-11分子筛催化剂合成,并应用于异丁烯直接胺化生产叔丁胺反应.传统水热技术合成的分子筛通常为粉末,机械强度不能达到实际应用的要求,在工业化过程中分子筛粉末一般需要加入粘结剂成型使其具备一定的机械强度和形状,但是粘结剂会降低分子筛催化剂的活性和选择性,有可能会引发一些副反应,因此无粘结剂分子筛催化剂引起人们广泛关注.无粘结剂分子筛是指分子筛颗粒中不含惰性粘结剂或只含有少量粘结剂,主要依靠分子筛晶粒间的相互作用支撑存在,具有一定形状、尺寸和机械强度的催化材料.无粘结剂分子筛催化剂中分子筛含量较高,可利用的有效表面积较大,在离子交换及工业催化等方面具有明显优势.本文采用水热合成的ZSM-11分子筛原粉与二氧化硅机械混合(ZSM-11/SiO2=70/30)挤条后,通过气固相合成法制备了无粘结剂ZSM-11分子筛催化剂(Cat-C).作为对比,还分别制备了ZSM-11和SiO2机械混合(ZSM-11/SiO2=70/30)样品HZSM-11+SiO2及ZSM-11和氧化铝机械混合(ZSM-11/Al2O3=70/30)样品HZSM-11+Al2O3.利用X射线衍射、透射电镜、NH3程序升温脱附和吸附吡啶红外光谱等对分子筛催化剂的物理化学性能进行了表征.同时,以这些分子筛样品为催化剂,在固定床反应装置上进行了异丁烯胺化反应评价,反应条件为270℃,5.0 MPa,氨烯比为4和异丁烯空速0.5 h?1.结果表明,与HZSM-11+SiO2和HZSM-11+Al2O3相比,Cat-C上叔丁胺生成速率最高.关联催化剂物化性能和反应性能发现,催化剂孔道结构与叔丁胺生成并不存在明显的关联性,而较多的Br?nsted酸和较少的Lewis酸才是Cat-C具有良好反应性能的主要原因.具有一定机械强度的无粘结剂ZSM-11分子筛催化剂制备简单,在异丁烯直接胺化过程中叔丁胺生成速率高,具有很好的工业化应用前景.     

High selective ethylbenzene obtainment through alkylation of dilute ethene with gas phase-liquid phase benzene and transalkylation feed

A novel industrial process was designed for the highly selective production of ethylbenzene. It comprised of a reactor vessel, vapor phase ethylene feed stream, benzene and transalkylation feed stream. Especially the product stream containing ethylbenzene was used to heat the reactor vessel, which consisted of an alkylation section, an upper heat exchange section, and a bottom heat exchange section. In such a novel reactor, vapor phase benzene and liquid phase benzene were coexisted due to the heat produced by isothermal reaction between the upper heat exchange section and the bottom heat exchange section. The process was demonstrated by the thermodynamic analysis and experimental results. In fact, during the 1010 hour-life-test of gas phase ethene with gas phase-liquid phase benzene alkylation reaction, the ethene conversion was above 95%, and the ethylbenzene selectivity was above 83% (only benzene feed) and even higher than 99% (benzene plus transalkylation feed). At the same time, the xylene content in the ethylbenzene was less than 100 ppm when the reaction was carried out under the reaction conditions of 140–185 °C of temperature, 1.6–2.1 MPa of pressure, 3.0–5.5 of benzene/ethylene mole ratio, 4–6 v% of transalkylation feed/(benzene+transalkylation feed), 0.19–0.27 h^?1 of ethene space velocity, and 1000 g of 3998 catalyst loaded. Thus, compared with the conventional ethylbenzene synthesis route, the transalkylation reactor could be omitted in this novel industrial process.