Unsymmetrical Pyrene‐Fused Phthalocyanine Derivatives: Synthesis,Structure, and Properties

Novel pyrene‐fused unsymmetrical phthalocyanine derivatives 2,3,9,10,16,17‐hexakis(2,6‐dimethylphenoxy)‐22,25‐diaza(2,7‐di‐tert‐butylpyrene)[4,5]phthalocyaninato zinc complex Zn[Pc(Pz‐pyrene)(OC₈H₉)₆] ( 1 ) and 2,3,9,10‐tra(2,6‐dimethylphenoxy)‐15,18,22,25‐traza(2,7‐di‐tert‐butylpyrene)[4,5]phthalocyaninato zinc compound Zn[Pc(Pz‐pyrene)₂(OC₈H₉)₄] ( 2 ) were isolated for the first time. These unsymmetrical pyrene‐fused phthalocyanine derivatives have been characterized by a wide range of spectroscopic and electrochemical methods. In particular, the pyrene‐fused phthalocyanine structure was unambiguously revealed on the basis of single crystal X‐ray diffraction analysis of 1 , representing the first structurally characterized phthalocyanine derivative fused with an aromatic moiety larger than benzene.     

Polypyrrole Shell@3D‐Ni Metal Core Structured Electrodes for High‐Performance Supercapacitors

Three‐dimensional (3D) nanometal films serving as current collectors have attracted much interest recently owing to their promising application in high‐performance supercapacitors. In the process of the electrochemical reaction, the 3D structure can provide a short diffusion path for fast ion transport, and the highly conductive nanometal may serve as a backbone for facile electron transfer. In this work, a novel polypyrrole (PPy) shell@3D‐Ni‐core composite is developed to enhance the electrochemical performance of conventional PPy. With the introduction of a Ni metal core, the as‐prepared material exhibits a high specific capacitance (726 F g^?1 at a charge/discharge rate of 1 A g^?1), good rate capability (a decay of 33 % in C_sp with charge/discharge rates increasing from 1 to 20 A g^?1), and high cycle stability (only a small decrease of 4.2 % in C_sp after 1000 cycles at a scan rate of 100 mV s^?1). Furthermore, an aqueous symmetric supercapacitor device is fabricated by using the as‐prepared composite as electrodes; the device demonstrates a high energy density (≈21.2 Wh kg^?1) and superior long‐term cycle ability (only 4.4 % and 18.6 % loss in C_sp after 2000 and 5000 cycles, respectively).     

Optical fiber acoustic sensing multiplexing system based on TDM/SFDM

We propose a system of time-division multiplexing(TDM) and spatial frequency-division multiplexing(SFDM). Extrinsic Fabry–Perot interferometric sensors are applied to detect weak acoustic signals. The broadband source is employed, the light from it is modulated by a pulse signal sequence and is efficiently amplified by semiconductor optical amplifiers. Experimental results show that the equivalent noise pressure spectrum level is-97.2 d B re 1 rad/√Hz below 1250 Hz, and the cross talk between two sensors in one TDM channel is-32.7 d B with a cavity length difference of 60 μm. The number of sensors in this multiplexing system can theoretically reach 160.     

Fatigue life enhancement by irradiation of 12Cr1MoV steel with a Zr<Superscript>+</Superscript> ion beam. Mesoscale deformation and fracture

The structure and properties of 12Cr1MoV steel irradiated with a zirconium ion beam were studied by optical microscopy, scanning electron microscopy, and micro- and nanoindentation. It is shown that the modification covers the entire cross-section of the irradiated specimens to a depth of 1 mm. The data on irradiation-induced structural changes are used to interpret the changes in mechanical properties of the irradiated specimens under static and cyclic loading. Particular attention is given to analysis of strain estimation by the digital image correlation method.     

Microtextures Induced by Nanosecond Laser on Ni–Co Alloy Coatings

Ni–Co alloys have a wide range of applications in various fields owning to their excellent physical, chemical, and mechanical properties. In this paper, we prepare Ni–Co alloy coatings on 316L stain steel surfaces by electroplating. We present a novel approach utilizing a nanosecond laser to induce microtextures on Ni–Co alloy coatings. We study experimentally the effects of laser power and scanning rate on the surface morphologies of Ni–Co alloy coatings. The results indicate that the shape and size of induced microtextures can be controlled by the laser power and scanning rate. The size of grains increases with increase in the work current of the laser (WCL) at a certain scanning rate. With the WCL constant, the size of grains decreases with increase in scanning rate while their average height increases. It is a simple and easily-controlled method for the fabrication of microstructures on Ni–Co alloy coatings, which has promising applications in investigations of the properties of microtextured surfaces, such as friction, adhesion, and wetting.