Determination of the elemental distribution in a sample using neutron induced gamma-ray emission tomography

The factors that affect accurate, quantitative results to be obtained by neutron induced gamma-ray emission tomography are stated. The technique, which is a combination of neutron activation analysis with computerised gamma-ray emission tomography, would be enhanced by the use of multiple detector assemblies, in geometrical configurations, which simultaneously record the gamma-rays emitted and improve detection efficiency. Developments in the past few years in positron emission tomography (PET) where scanners made of single scintillation block detectors, cut into smaller segments, to form individual crystal detector elements and packed in ring around the radioactive object, are discussed. The coincident detection efficiency for annihilation photons and cascade gamma-rays for such systems are considered and the possibilities of carrying out NIGET with coincident gamma-ray tomography are explored whilst indicating some of the limitations. This is an area which requires further, intense investigation and has an impact on a wide range of applications, particularly in the biomedical field.     

A cone programming approach to the bilinear matrix inequality problem and its geometry

We discuss an approach for solving the Bilinear Matrix Inequality (BMI) based on its connections with certain problems defined over matrix cones. These problems are, among others, the cone generalization of the linear programming (LP) and the linear complementarity problem (LCP) (referred to as the Cone-LP and the Cone-LCP, respectively). Specifically, we show that solving a given BMI is equivalent to examining the solution set of a suitably constructed Cone-LP or Cone-LCP. This approach facilitates our understanding of the geometry of the BMI and opens up new avenues for the development of the computational procedures for its solution. Research supported in part by the National Science Foundation under Grant CCR-9222734.     

A high-throughput approach for the determination of pesticide residues in cucumber samples using solid-phase microextraction on 96-well plate

A high-throughput solid-phase microextraction (SPME) on 96-well plate together with gas chromatography–mass spectrometry (GC–MS) was developed for the determination of some selected pesticides in cucumber samples. Pieces with the length of 1.0 cm of silicon tubing were precisely prepared and then coated on the end part of stainless steel wires. The prepared fibers were positioned in a home-made polytetrafluoroethylene (PTFE)-based constructed ninety-six holes block to have the possibility of simultaneous immersion of the SPME fibers into the center of individual wells. Pesticides such as diazinon, penconazol, tebuconazol, bitertanol, malathion, phosalone and chlorpyrifos-methyl were selected for their highly application in cucumber field. The performances of the SPME fibers, such as intra and inter-fibers reproducibility, were evaluated and the results showed a good similarity in extraction yields. A volume of 1 mL of the aquatic supernatant of the cucumber samples was transferred into the 96-well plate and the array of SPME fibers was applied for the extraction of the selected pesticides. The important parameters influencing the whole extraction process including, organic solvent percent, salt addition, dilution factor, stirring rate and extraction time were optimized. The inter- and intra-day RSD% were found to be less than 15.4%. Limits of detection (LOD) and limits of quantification (LOQ) were below 60 and 180 μg kg⁻¹, respectively. The coefficient of determination was satisfactory (r² > 0.99) for all the studied analytes. The developed method was successfully applied to the monitoring of several samples gathered from local markets.     

Mg–Al layered double hydroxide intercalated with manganese(III) 5,10,15,20‐tetrakis(4‐benzoate)porphyrinacetate as a highly reusable catalyst for epoxidation

The preparation and characterization are presented of a new catalytic material comprising Mg–Al layered double hydroxide and intercalated manganese(III) 5,10,15,20‐tetrakis(4‐benzoate)porphyrinacetate. Characterization was realized via various techniques. The prepared composite exhibited excellent catalytic activity in the selective epoxidation of various olefins with tetra‐n‐butylammonium hydrogen monopersulfate as an oxidant under mild reaction conditions. Furthermore, the catalytic system could be reused nine times without significant reduction in conversion percentage and any special care or additional treatment of the catalyst.     

Multiple-Spacecraft Reconfiguration Through Collision Avoidance,Bouncing, and Stalemate

We consider constrained multiple-spacecraft reconfigurations outside a gravity well in deep space. As opposed to the single-spacecraft scenario, such reconfigurations involve collision avoidance constraints that can be embedded in a nonconvex, state-constrained optimal control problem. Due to the difficulties in solving this general class of optimal control problems, we adopt a heuristically motivated approach to multiple-spacecraft reconfigurations. Then, we proceed to prove the convergence properties of the proposed approach for reconfigurations involving an arbitrary number of spacecraft.     

Sensitization of the analytical methods for photoneutron calculations to the wall concrete composition in radiation therapy

The effect of wall material on photoneutron production in radiation therapy rooms was studied using Monte Carlo (MC) simulations. An analytical formula was proposed to take into account the concrete composition in photoneutron dose calculations. Using the MCNPX MC code, the 18 MV photon beam of the Varian Clinac 2100 and a typical treatment room with concrete compositions according to report No. 144 of National Council of Radiation Protection (NCRP) were simulated. Number of room produced photoneutrons per Gray of X-ray at the isocenter was determined for different types of concrete and named as “Q_W”. This new factor was inserted in the used formula for photoneutron fluence calculations at the inner entrance of maze. The photoneutron fluence was calculated using new proposed formula at the inner entrance of maze for all studied concretes. The difference between conventional and proposed equations varied from 11% to 46% for studied concretes. It was found that room produced photoneutrons could be significant for high density concretes. Additionally, applying the new proposed formula can consider the effect of wall material composition on the photoneutron production in high energy radiation therapy rooms. Further studies to confirm the accuracy of newly developed method is recommended.