康普顿效应中电子-光子碰撞过程的研究

康普顿散射公式中光子波长的连续变化与光量子假说在表面上存在着不一致.为此文章分析了康普顿效应中电子和光子的碰撞过程,指出康普顿散射光子波长的连续变化可以通过自由电子连续的“虚光子吸收”和“虚光子发射”过程来加以说明.     

洛仑兹变换公式的一个推广

将通常的洛仑兹坐标变换公式和速度变换公式推广到了一个更一般的情况。     

尖端放电中的极性效应

基于气体击穿的汤森德理论和流注理论定性地分析了一个尖端放电演示实验中极板的极性对放电过程的影响．指出了尖端接电源的阳极时击穿电压比接阴极时低的原因．     

光栅色散的新型演示实验

本文介绍了一种适合于课堂使用的光栅色散现象的新型演示实验装置.     

Simultaneous qualitative assessment and quantitative analysis of flavonoids in various tissues of lotus (Nelumbo nucifera) using high performance liquid chromatography coupled with triple quad mass spectrometry

Flavonoid composition and concentration were investigated in 12 different tissues of ‘Ti-1’ lotus (Nelumbo nucifera) by high performance liquid chromatography equipped with photodiode array detection tandem electrospray ionization mass spectrometry (HPLC-DAD-ESI-MSⁿ). A total of 20 flavonoids belonging to six groups (myricetin, quercetin, kaempferol, isohamnetin, diosmetin derivatives) were separated and identified. Myricetin 3-O-galactoside, myricetin 3-O-glucuronide, isorhamnetin 3-O-glucuronide and free aglycone diometin (3′,5,7-trihydroxy-4′-methoxyflavone) were first reported in lotus. Flavonoid composition varied largely with tissue type, and diverse compounds (5–15) were found in leaf and flower stalks, flower pistils, seed coats and embryos. Flower tissues including flower petals, stamens, pistils, and, especially, reproductive tissue fruit coats had more flavonoid compounds (15–17) than leaves (12), while no flavonoids were detectable in seed kernels. The flavonoid content of seed embryos was high, 730.95 mg 100 g⁻¹ DW (dry weight). As regards the other tissues, mature leaf pulp (771.79 mg 100 g⁻¹ FW (fresh weight)) and young leaves (650.67 mg 100 g⁻¹ FW) had higher total flavonoid amount than flower stamens (359.45 mg 100 g⁻¹ FW) and flower petals (342.97 mg 100 g⁻¹ FW), while leaf stalks, flower stalks and seed coats had much less total flavonoid (less than 40 mg 100 g⁻¹ FW).     

Enhanced galloping energy harvester with cooperative mode of vibration and collision

The low power and narrow speed range remain bottlenecks that constrain the application of small-scale wind energy harvesting. This paper proposes a simple, low-cost, and reliable method to address these critical issues. A galloping energy harvester with the cooperative mode of vibration and collision (GEH-VC) is presented. A pair of curved boundaries attached with functional materials are introduced, which not only improve the performance of the vibration energy harvesting system, but also convert more mechanical energy into electrical energy during collision. The beam deforms and the piezoelectric energy harvester (PEH) generates electricity during the flow-induced vibration. In addition, the beam contacts and separates from the boundaries, and the triboelectric nanogenerator (TENG) generates electricity during the collision. In order to reduce the influence of the boundaries on the aerodynamic performance and the feasibility of increasing the working area of the TENG, a vertical structure is designed. When the wind speed is high, the curved boundaries maintain a stable amplitude of the vibration system and increase the frequency of the vibration system, thereby avoiding damage to the piezoelectric sheet and improving the electromechanical conversion efficiency, and the TENG works with the PEH to generate electricity. Since the boundaries can protect the PEH at high wind speeds, its stiffness can be designed to be low to start working at low wind speeds. The electromechanical coupling dynamic model is established according to the GEH-VC operating principle and is verified experimentally. The results show that the GEH-VC has a wide range of operating wind speeds, and the average power can be increased by 180% compared with the traditional galloping PEH. The GEH-VC prototype is demonstrated to power a commercial temperature sensor. This study provides a novel perspective on the design of hybrid electromechanical conversion mechanisms, that is, to combine and collaborate based on their respective characteristics.

     

钙钛矿型稀土氧化物的合成及其能源转化储存应用研究进展

钙钛矿型稀土氧化物价格低廉、结构可控、性质多样,在催化领域有着广阔的应用前景。本文从钙钛矿型稀土氧化物的结构类型、合成方法及电化学催化反应出发,总结了传统高温合成方法、火焰喷雾法、静电纺丝法和脉冲激光沉积法等几种最常用的合成方法,以及提升其氧析出反应(OER),氢析出反应(HER)和氧还原反应(ORR)催化能力的典型有效方法,概述了近年来钙钛矿型稀土氧化物在电解水、金属空气电池和固体氧化物燃料电池等能源转化储存装置的主要研究进展,进而对钙钛矿型稀土氧化物在能源转化储存领域的应用进行了展望。     

Modeling of Influence of Helix Geometry on the Constitutive Parameters of the Chiral Medium

Computations are made to estimate the influence of geometry of the helixes in an artificial chiral medium made by embedding small conducting helives in a lossy isotropic host material on the three constitutive parameters of the medium, by using a proposed model which explicitly includes the first-order effects of reradiation from the helixes, near-field loses and mutual coupling between helixes.     

一个静电问题的能量解释

本文从能量的角度讨论了一个静电问题.     

关于开尔文表述和克劳修斯表述的等价性的一点讨论

讨论了热力学第二定律的开尔文表述和克劳修斯表述的等价性的一个问题