Sensitivity analysis of thermal performances of flat plate solar air heaters

Sensitivity analysis is a mathematical tool, first developed for optimization methods, which aim is to characterize a system response through the variations of its output parameters following modifications imposed on the input parameters of the system. Such an analysis may quickly become laborious when the thermal model under consideration is complex or the number of input parameters is high. In this paper, we develop a mathematical model to analyse the heat exchanges in four different types of solar air collectors. When building this thermal model we show that for each collector, at quasi-steady state, the energy balance equations of the components of the collector cascade into a single first-order non-linear differential equation that is able to predict the thermal behaviour of the collector. Our heat transfer model clearly demonstrates the existence of an important dimensionless parameter, referred to as the thermal performance factor of the collector, that compares the useful thermal energy which can be extracted from the heater to the overall thermal losses of that collector for a given set of input parameters. A sensitivity analysis of our thermal model has been performed for the most significant input parameters such as the incident solar irradiation, the inlet fluid temperature, the air mass flow rate, the depth of the fluid channel, the number and nature of the transparent covers in order to measure the impact of each of these parameters on our model. An important result which can be drawn from this study is that the heat transfer model developed is robust enough to be used for thermal design studies of most known flat plate solar air heaters, but also of flat plate solar water collectors and linear solar concentrators.     

Inverse gas chromatography of lignocellulosic fibers coated with a thermosetting polymer: Use of peak maximum and conder and young methods

The Conder and Young (CY) and the peak maximum (PM) methods were used to estimate the retention time of n-alkane probes on chemithermomechanical pulp (CTMP) wood fibers treated with a low molecular weight grade phenol-formaldehyde resin (PFR). Thermodynamic functions (ΔH_a^o, ΔG_a^o, and ΔS_a^o) and the London dispersive component of the surface energy were derived from these retention times. Treated wood fibers show a high energy surface due to the presence of the thermoset resin on their surface. Values of ΔH_a^o obtained from the CY method were higher than those obtained with the PM method at relatively high temperatures and with relatively low molecular weight alkanes. The results from the two methods were identical at low temperature (293 K) and with the relatively high molecular weight alkane n-undecane.     

非线性双曲型积分微分方程有限元逼近的误差分析

考虑非线性双曲型积分微分方程半离散有限元格式，得到H^1超收敛和最优阶L^∞和W^1,∞模误差估计，结果丰富了有限元方法的理论。     

Impulse control of pension fund contributions,in a regime switching economy

In defined benefit pension plans, allowances are independent from the financial performance of the fund. And the sponsoring firm pays regularly contributions to limit deviations of fund assets from the mathematical reserve, necessary for covering the promised liabilities. This research paper proposes a method to optimize the timing and size of contributions, in a regime switching economy. The model takes into consideration important market frictions, like transactions costs, late payments and illiquidity. The problem is solved numerically using dynamic programming and impulse control techniques. Our approach is based on parallel grids, with trinomial links, discretizing the asset return in each economic regime.     

Optimal design of profit sharing rates by FFT

This paper addresses the calculation of a fair profit sharing rate for participating policies with a minimum interest rate guaranteed. The bonus credited to policies depends on the performance of a basket of two assets: a stock and a zero coupon bond and on the guarantee. The dynamics of the instantaneous short rates are driven by a Hull and White model, whereas the stocks follow a double exponential jump-diffusion model. The participation level is determined such that the return retained by the insurer is sufficient to hedge the interest rate guaranteed. Given that the return of the total asset is not lognormal, we rely on a Fast Fourier Transform to compute the fair value of bonus and guarantee options.     

Backscatter factor and absorption ratio of fibrous zirconia media in the visible

Fibrous thermal insulations are widely used to conserve energy in ambient to high temperature applications including buildings, solar collectors, heat exchangers, furnaces and thermal protection systems of reusable launch vehicles. It has long been recognised that zirconia has the lowest thermal conductivity of commercial refractories. The thermal conductivity of a zirconia fibrous medium is strongly dependent of its bulk density; high bulk densities of zirconia fibers provide the most effective insulation at high temperatures. Lee's theory for radiative transfer through fibrous media is used in this paper. The two-flux model is applied to determine the backward and forward parameters of a medium of zirconia fibers oriented in parallel planes. Theoretical calculations of the backscatter factor and absorption ratio of this medium are carried out in the visible spectrum for different size parameters of the fibers and for three different temperatures. Our results show that the backscatter factor of zirconia fibrous insulations is maximum, and therefore the heat transfer by the fibrous medium is the lowest, for a size parameter of 0.45 for all the temperatures studied. We also observed that the backscatter factor decreases with increasing temperature.     

“Printing” DNA Strand Patterns on Small Molecules with Control of Valency,Directionality, and Sequence

The incorporation of synthetic molecules as corner units in DNA structures has been of interest over the last two decades. In this work, we present a facile method for generating branched small molecule‐DNA hybrids with controllable valency, different sequences, and directionalities (5′–3′) using a “printing” process from a simple 3‐way junction structure. We also show that the DNA‐imprinted small molecule can be extended asymmetrically using polymerase chain reaction (PCR) and can be replicated chemically. This strategy provides opportunities to achieve new structural motifs in DNA nanotechnology and introduce new functionalities to DNA nanostructures.     

A new stable space–time formulation for two‐dimensional and three‐dimensional incompressible viscous flow

A space–time finite element method for the incompressible Navier–Stokes equations in a bounded domain in ?^d (with d=2 or 3) is presented. The method is based on the time‐discontinuous Galerkin method with the use of simplex‐type meshes together with the requirement that the space–time finite element discretization for the velocity and the pressure satisfy the inf–sup stability condition of Brezzi and Babu?ka. The finite element discretization for the pressure consists of piecewise linear functions, while piecewise linear functions enriched with a bubble function are used for the velocity. The stability proof and numerical results for some two‐dimensional problems are presented. Copyright © 2001 John Wiley & Sons, Ltd.     

Elucidation of the Structure of Organic Solutions in Solvent Extraction by Combining Molecular Dynamics and X‐ray Scattering

Knowledge of the supramolecular structure of the organic phase containing amphiphilic ligand molecules is mandatory for full comprehension of ionic separation during solvent extraction. Existing structural models are based on simple geometric aggregates, but no consensus exists on the interaction potentials. Herein, we show that molecular dynamics crossed with scattering techniques offers key insight into the complex fluid involving weak interactions without any long‐range ordering. Two systems containing mono‐ or diamide extractants in heptane and contacted with an aqueous phase were selected as examples to demonstrate the advantages of coupling the two approaches for furthering fundamental studies on solvent extraction.     

“Printing” DNA Strand Patterns on Small Molecules with Control of Valency,Directionality, and Sequence

The incorporation of synthetic molecules as corner units in DNA structures has been of interest over the last two decades. In this work, we present a facile method for generating branched small molecule‐DNA hybrids with controllable valency, different sequences, and directionalities (5′–3′) using a “printing” process from a simple 3‐way junction structure. We also show that the DNA‐imprinted small molecule can be extended asymmetrically using polymerase chain reaction (PCR) and can be replicated chemically. This strategy provides opportunities to achieve new structural motifs in DNA nanotechnology and introduce new functionalities to DNA nanostructures.