Rank 2 Ample Vector Bundles on Some Smooth Rational Surfaces

Several classification results for ample vector bundles of rank 2 on Hirzebruch surfaces, and on Del Pezzo surfaces, are obtained. In particular, we classify rank 2 ample vector bundles with _c2 less than seven on Hirzebruch surfaces, and with _c2 less than four on Del Pezzo surfaces.     

Facilitated sulfate transfer across the nitrobenzene-water interface as mediated by hydrogen-bonding ionophores.

Facilitated SO4(2-) transfers by hydrogen bond-forming ionophores are investigated across the nitrobenzene (NB)-water interface by using polarography with a dropping electrolyte electrode. Bis-thiourea 1, alpha,alpha'-bis(N'-p-nitrophenylthioureylene)-m-xylene, is found to significantly facilitate the transfer of the highly hydrophilic SO4(2-) whereas its counterpart, N-(p-nitrophenyl)-N'-propylthiourea (ionophore 2), cannot. In contrast to the predominant formation of a 1:1 complex with SO4(2-) in the bulk NB phase, the SO4(2-) transfer assisted by 1 is indeed based on the formation of a 1:2 complex between SO4(2-) and ionophore, even under the condition of [SO4(2-)]aq > [1]org. Such an exclusive formation of the 1:2 (SO4(2-) to ionophore) complex at the NB-water interface is not observed with structurally similar bis-thiourea 3, alpha,alpha'-bis(N'-phenylthioureylene)-m-xylene, where p-nitrophenyl moietes of bis-thiourea 1 are simply replaced by phenyl groups. The facilitated transfer of SO4(2-) with bis-thiourea 1 is further compared to that of HPO4(2-) and H2PO4- across the NB-water interface, which was previously shown to be assisted by 1 through the formation of the 1:1 and 2:1 (anion to ionophore) complexes, respectively. On the basis of these examinations, unique binding behaviors of hydrogen bond-forming ionophores at the NB-water interface are discussed, with a view towards development of ionophore-based anion-selective chemical sensors.     

Temporal analysis of products (TAP) study on oxygen storage properties over Pt−Rh/CeO2 catalyst

The oxygen storage capacity of CeO₂, Ce_0.9Pr_0.1O₂, Pt?Rh/CeO₂ and Pt?Rh/Ce_0.9Pr_0.1O₂ was investigated by conventional GC pulse method and transient pulse techniques. It is shown that incorporation of PrO_y into CeO₂ matrix strongly promotes oxygen storage capacity (OSC) measured using the transient pulse technique. The improvement of OSC at low temperature is observed in Pt?Rh loaded onto CeO₂ and Ce?Pr catalysts.     

Basic study of the gelation of dimethacrylate‐type crosslinking agents

An investigation was made of the gelation of dimethacrylate‐type crosslinking agents in view of an application for separation media. The study mainly centered on a crosslinking agent, glycerol dimethacrylate (GDMA), which is relatively hydrophilic because of a hydroxyl group in the middle of its structure. The gelation of GDMA was compared with that of other hydrophobic crosslinking agents such as ethylene glycol dimethacrylate and 1,6‐hexanediol dimethacrylate. The diluents used in the study were toluene, toluene with methanol, and cyclohexanol. The gelation was observed in real time with a charge coupled device camera and dynamic light scattering (DLS). Also, the separated dry gels were extensively characterized with scanning electron microscopy, BET (N₂ absorption and desorption isotherm), and Fourier transform infrared. DLS analysis showed a stronger molecular interaction of GDMA gelation in toluene, whereas this interaction was much weaker in an alcoholic solvent such as toluene with methanol or cyclohexanol. This indicated that GDMA gelation might proceed through hydrogen bonding as well as a crosslinking reaction of vinyl groups. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 949–958, 2006     

Photografting of vinyl polymers onto ultrafine inorganic particles: Photopolymerization of vinyl monomers initiated by AZO groups introduced onto these surfaces

The photografting of polymers onto ultrafine inorganic particles, such as silica and titanium oxide, initiated by azo groups introduced onto these surfaces was investigated. The introduction of azo groups onto the particles was achieved by the reaction of 4,4′-azobis(4-cyanopentanoic acid) with surface isocyanate groups, which were introduced by the treatment with tolylene 2,4-diisocyanate. It was found that the photopolymerization of vinyl monomers, such as methyl methacrylate (MMA), styrene, and N-vinylcarbazole, is initiated by ultrafine particles having azo groups. The corresponding polymers were effectively grafted onto these surfaces through the propagation of the polymer from the surface radicals formed by the photodecomposition of the azo groups: e.g., the percentage of grafting of PMMA and polystyrene onto silica was reached to 112 and 176%, respectively. The percentage of grafting onto silica in the graft polymerization initiated by photodecomposition of surface azo groups was much larger than that initiated by thermal decomposition. Polymer-grafted ultrafine particles thus obtained gave a stable colloidal dispersion in good solvents for the grafted chain. © 1994 John Wiley & Sons, Inc.     

Construction of a new multi-turn time-of-flight mass spectrometer

A new type of multi-turn time-of-flight mass spectrometer was constructed, consisting of four cylindrical electric sectors and 28 electric quadrupole lenses, the size of the vacuum chamber being 60 x 70 x 20 cm. It was demonstrated that the mass resolution can be increased according to the number of cycles of the ions through the ion optical system.     

Flow injection system with in-line Winkler's procedure using 16-way valve and spectrofluorimetric determination of dissolved oxygen in environmental waters

Flow injection spectrofluorimetry with in-line Winklers procedure was developed for the dissolved oxygen (DO) determination. 2-Thionaphthol reacted with iodine produced by Winkler’s method to form fluorescence inactive disulfide compound. To automate the process completely, a 5-channel flow system with a newly designed 16-way valve was assembled. The system consisted of a dispersion coil (DC), a precipitate formation coil (PFC), a precipitate dissolving coil (PDC), and extraction coil (EC). A calibration can be constructed by using a standard iodine solution for dissolved oxygen. The calibration graph was linear over the range 1.2×10⁻⁴∼6.0×10⁻⁴ mol l⁻¹ iodine (1.96∼9.80 mg O l⁻¹)). The relative standard deviation (n=6) was below 0.3% for the 4×10⁻⁴ mol l⁻¹ iodine (6.27 mg O l⁻¹) determination. The sample throughput was 12/h.