Crosslinking network of bio‐based bis‐functional epoxides derived from trans‐limonene oxide

The thiol‐ene reaction between trans‐limonene oxide (trans‐LO) and ethane‐1,2‐dithiol in the presence of triethylborane affords a bio‐based bis‐functional epoxide (bis‐trans‐LO). The crosslinking reaction of bis‐trans‐LO with branched polyethyleneimine (BPEI; M_n = 600; BPEI₆₀₀) at a feed ratio of bis‐trans‐LO/BPEI₆₀₀ = 57/43 (wt/wt) yields the corresponding network polymer with T_d10 (10% thermal decomposition temperature) of 304.7 °C in 98% yield. In contrast, negligible amounts of network polymer are obtained by the reaction of bis‐LO (bis‐functional epoxide derived from cis and trans‐LO) and BPEI₆₀₀ regardless of the feed ratio. The mechanical strengths as measured by direct tensile tests of the network polymers derived from bis‐trans‐LO and BPEI_600,1800 (M_n = 600 and 1800) were approximately 16 and 11 times higher than that of bis‐LO and BPEI₁₈₀₀, respectively. The tensile shear strengths of the metal‐to‐metal adhesive bonds induced by bis‐trans‐LO and BPEI_600,1800 were 9.5 and 14.1 MPa, respectively. DMA revealed that the storage modulus of the network polymer derived from bis‐trans‐LO and BPEI₁₈₀₀ in the rubber region was higher than that of the material prepared from bis‐LO and BPEI₁₈₀₀, indicating higher crosslink density of the bis‐trans‐LO/BPEI₁₈₀₀ system. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2466–2473     

Simulation of a High Harmonic Gyrotron with Axis-Encircling Electron Beam and Permanent Magnet

A computer code for simulation of beam-field interaction in a resonant cavity of a gyrotron has been developed. It is based on a self-consistent, time-independent, single-mode physical model. The code has been applied to the analysis of the electrodynamical system of a novel high-harmonic gyrotron with axis-encircling beam and a permanent magnet. In this paper both the physical model and numerical techniques used are outlined. Some results of the numerical experiments are presented and discussed.     

Numerical analysis of turbulent structure in compound meandering open channel by algebraic Reynolds stress model

The turbulent flow in a compound meandering channel with a rectangular cross section is one of the most complicated turbulent flows, because the flow behaviour is influenced by several kinds of forces, including centrifugal forces, pressure‐driven forces and shear stresses generated by momentum transfer between the main channel and the flood plain. Numerical analysis has been performed for the fully developed turbulent flow in a compound meandering open‐channel flow using an algebraic Reynolds stress model. The boundary‐fitted coordinate system is introduced as a method for coordinate transformation in order to set the boundary conditions along the complicated shape of the meandering open channel. The turbulence model consists of transport equations for turbulent energy and dissipation, in conjunction with an algebraic stress model based on the Reynolds stress transport equations. With reference to the pressure–strain term, we have made use of a modified pressure–strain term. The boundary condition of the fluctuating vertical velocity is set to zero not only for the free surface, but also for computational grid points next to the free surface, because experimental results have shown that the fluctuating vertical velocity approaches zero near the free surface. In order to examine the validity of the present numerical method and the turbulent model, the calculated results are compared with experimental data measured by laser Doppler anemometer. In addition, the compound meandering open channel is clarified somewhat based on the calculated results. As a result of the analysis, the present algebraic Reynolds stress model is shown to be able to reasonably predict the turbulent flow in a compound meandering open channel. Copyright © 2005 John Wiley & Sons, Ltd.     

Estimation of growth rate in unidirectionally solidified multicrystalline silicon by the growth-induced striation method

Multicrystalline silicon was grown by unidirectional solidification method using the accelerated crucible rotation technique. The application of the accelerated crucible rotation technique in unidirectional solidification method induced growth striations across the axial direction of the grown crystal. This striation pattern was observed from carbon concentration distribution, obtained by using Fourier transform infrared spectroscopy. The generated striation pattern was found to be weak and discontinuous. Some striations were absent, probably due to back melting, caused during each crucible rotation. From the growth striations and applied time period in crucible rotation, the growth rate was estimated by using Fourier transformation analysis.     

Temperature dependence of the exafs spectrum in YBa2Cu3O7−δ compounds

The temperature dependence of the extended X-ray absorption fine structure (EXAFS) is studied in the high T_c superconductors, YBa₂Cu₃O_7−δ. The measurements were done at the Cu K-edge for samples of two orthorhombic phases (T_c≈90 K and ≈58 K, respectively) and a nonsuperconducting tetragonal phase. Interatomic distances and mean square relative displacements σ² for Cu-O bonds are determined by the least squares refinement. The results indicate that values of σ² increase near T_c for both the orthorhombic samples. It is concluded that this anomalous behavior related to T_c is caused by an anomalous vibration of oxygen atoms in the Ba-O layer. Changes in the Cu-O distances from 300 to 20 K are not found.     

Measurement of circular dichroism spectra of liquid/liquid interface by centrifugal liquid membrane method.

The direct measurement of the circular dichroism (CD) spectra of liquid/liquid interface has been achieved for the first time by the centrifugal liquid membrane (CLM) method combined with a conventional CD spectropolarimetry. In the sample chamber of the CD spectropolarimeter, a cylindrical glass cell containing small amounts of organic and aqueous phases was rotated at ca. 7000 rpm to generate a two-phase liquid membrane with a high specific interfacial area. The CD spectra of the J-aggregate of protonated 5,10,15,20-tetraphenylporphyrin formed at the toluene/sulfuric acid interface in the rotating cell have been measured. The results demonstrated the novelty and advantages of this method.     

Surface-enhanced Raman scattering from oleate-stabilized silver colloids at a liquid/liquid interface.

Oleate-stabilized silver colloids of 5-nm-diameter were adsorbed to a toluene/water interface, and surface enhanced Raman scattering (SERS) spectra from these colloids were measured under the total internal reflection (TIR) condition. From the observed spectra, we examined the states of oleate ions and toluene molecules on silver colloids at the liquid/liquid interfacial region. The TIR-SERS spectra of oleate ions showed stronger peaks of the carboxylate group and the ethylene group than those of alkyl chains. From these results, it was found that the oleate ions were adsorbed on the silver surface in two different ways at the liquid/liquid interface; the carboxylate group adsorbed in the organic phase side, while the ethylene group adsorbed in the aqueous phase side. The shifts of the toluene in the interfacial SERS spectra were identical to those of bulk toluene, though the relative intensities among the peaks were not same. This result suggested that the toluene was adsorbed with a weak interaction, but was significantly enhanced by the local electromagnetic field at the colloid surface.