Structural developments in synthetic rubbers during uniaxial deformation by in situ synchrotron X‐ray diffraction

The molecular orientation and strain‐induced crystallization of synthetic rubbers—polyisoprene rubber, polybutadiene rubber, and butyl rubber [poly(isobutylene isoprene)]—during uniaxial deformation were studied with in situ synchrotron wide‐angle X‐ray diffraction. The high intensity of the synchrotron X‐rays and the new data analysis method made it possible to estimate the mass fractions of the strain‐induced crystals and amorphous chain segments in both the oriented and unoriented states. Contrary to the conventional concept, the majority of the molecules (50–75%) remained in an unoriented amorphous state at high strains. Each synthetic rubber showed a different behavior of strain‐induced crystallization and molecular orientation during extension and retraction. Our results confirmed the occurence of strain‐induced networks in the synthetic rubbers due to the inhomogeneity of the crosslink distribution. The strain‐induced networks containing microfibrillar crystals and oriented amorphous tie chains were responsible for the ultimate mechanical properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 956–964, 2004     

Terahertz time-domain spectra of aromatic carboxylic acids incorporated in nano-sized pores of mesoporous silicate.

Terahertz time-domain spectroscopy (THz-TDS) is used to study the intra- and intermolecular vibrational modes of aromatic carboxylic acids, for example, o-phthalic acid, benzoic acid, and salicylic acid, which form either intra- or intermolecular hydrogen bond(s) in different ways. Incorporating the target molecules in nano-sized spaces in mesoporous silicate (SBA-16) is found to be effective for the separate detection of intramolecular hydrogen bonding modes and intermolecular modes. The results are supported by an analysis of the differences in the peak shifts, which depend on temperature, caused by the different nature of the THz absorption. Raman spectra revealed that incorporating the molecules in the nano-sized pores of SBA-16 slightly changes the molecular structures. In the future, THz-TDS using nanoporous materials will be used to analyze the intra- and intermolecular vibrational modes of molecules with larger hydrogen bonding networks such as proteins or DNA.     

Polybenzimidazoles containing anthracene photodimer

Polybenzimidazoles that contained anthracene photodimer were prepared. The molecular weights of the polymers prepared by the photopolymerization of bis-anthrylbenzimidazoles were limited by the precipitation of the resulting polymers from the reaction organic solvents. Higher molecular weight polymers were obtained by the photopolymerization of bis-anthryl-Schiff's bases, followed by the oxidation of the resulting polymers. These polymers were soluble in acidic solvents such as formic and sulfuric acids but were insoluble in organic solvents.     

Quantitative assessment of solid oxide electrochemical doping

Quantitative analysis of metal cation doping by solid oxide electrochemical doping (SOED) has been performed under galvanostatic doping conditions. A M–β″-Al₂O₃ (M=Ag, Na) microelectrode (contact radius: about 10 μm) was used as cation source to attain a homogeneous solid–solid contact between the β″-Al₂O₃ and doping target. In Ag doping into alkali borate glass, the measured dopant amount closely matched the theoretical value. High Faraday efficiencies of above 90% were obtained. This suggests that the dopant amount can be precisely controlled on a micromole scale by the electric charge during electrolysis. On the other hand, current efficiencies of Na doping into Bi₂Sr₂CaCu₂O_y (BSCCO) ceramics depended on the applied constant current. Efficiencies of above 80% were achieved at a constant current of 10 μA (1.6 A cm⁻²). The relatively low efficiencies were explained by the saturation of BSCCO grain boundaries with Na. By contrast, excess Na was detected on the anodic surface of ceramics at a constant current of 100 μA (16 A cm⁻²). In the present study, we demonstrate that SOED enables micromole-scale control over dopant amount.     

Thermal properties and fracture toughness of a liquid‐crystalline epoxy resin cured with an aromatic diamine crosslinker having a mesogenic group

A mesogenic‐type curing agent was synthesized to introduce a mesogenic group not only into epoxy resin backbones but also into the crosslink units. In the mesogenic curing agent system, the domain size became larger, and the network arrangement in each domain existed to a greater extent than that in a system cured with the ordinary diamine curing system according to the evidence from polarized optical micrographs and polarized Fourier transform infrared mapping measurements. Moreover, the fracture toughness of the system was considerably improved. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2486–2494, 2006     

Polymerization and copolymerization of methacrylic esters derived from glycidyl methacrylate

Copolymerization of methacrylic esters derived from glycidyl methacrylate and nucleophiles with styrene was carried out. The monomer reactivity ratios of these methacrylic esters were varied with the alkoxy groups of the esters and the solvent used.     

Polymerization of α-amino acid N-carboxy anhydride. IX. Copolymerization of α-amino acid N-carboxy anhydride in heterogeneous system

Copolymerization of NCA's was undertaken in a heterogeneous system in acetonitrile, which is not a solvent of the polypeptides. The reactivity ratio was calculated by using the Lewis-Mayo equation. Further, the conversion rate in the copolymerization and the configuration of the copolymer produced were compared with those of the copolymerization in the homogeneous system in nitrobenzene, in which the copolypeptides are swollen. The rate of copolymerization in acetonitrile was between the rates of polymerization of the individual monomers. It has been reported that the configuration of the copolymer obtained in dimethylformamide, in which the copolypeptides are swollen, is of the block type. On the other hand, many polypeptides obtained in acetonitrile, which is not a solvent of the copolypeptides, had a random configuration near to an alternating configuration.     

Polymerization of methacrylates. I. Polymerization reactivity of picryl methacrylate

The polymerization of picryl (PMA), 2,4-dinitrophenyl (2,4-DNMA),2,6-dinitrophenyl (2,6-DNMA), 2-methyl-4,6-dinitrophenyl (MDNMA), and 2,6-dimethylphenyl methacrylates (DMMA) was carried out in benzene at 60°C. PMA, 2,6-DNMA, and MDNMA did not undergo radical homopolymerization, while 2,4-DNMA and DMMA did. The results suggest that the growing radical readily attacks the oxygen atom of the nitro group at the 2 position of the terminal phenyl group due to the steric effect of the substituent at the 6 position, resulting in chain termination. PMA formed a charge-transfer complex with 2-naphthyl methacrylate (NMA). The stoichiometric composition of this complex was shown to be 1:1 molar complex. PMA was readily copolymerized with NMA. The amount of solvent affected the composition of the copolymer obtained at a given same mole fraction in feed. The results suggest that charge-transfer interaction between the ester groups affects the copolymerization mechanism.     

Development of rectangular column structured titanium oxide photocatalysts anchored on silica sheets by a wet process

Commercially available powdered photocatalysts such as P-25 are known to show high photocatalytic performance. However, in practical use, their anchoring onto a substrate without any binders is still very difficult. The purpose of this study is to design and develop high-performance photocatalysts that can be anchored onto a substrate, and to this end we have prepared a titanium oxide photocatalyst using a wet process. The results of this study led to the successful development of rectangular column structured titanium oxide crystals which could be anchored onto silica sheets. The rectangular columnar crystal was 100- 500 nm wide and 1000- 5000 nm long. Moreover, investigations on the complete oxidation reaction of acetaldehyde into CO₂ and H₂O showed a high performance equivalent to that of the most efficient marketed powdered photocatalysts.     

Automated multi-attribute method sample preparation using high-throughput buffer exchange tips

Rationale

The multi-attribute method (MAM) has become a valuable mass spectrometry (MS)-based tool that can identify and quantify the site-specific product attributes and purity information for biotherapeutics such as monoclonal antibodies (mAbs) and fusion molecules in recent years. As we expand the use of the MAM at various stages of drug development, it is critical to enhance the sample preparation throughput without additional chemical modifications and variability.

Methods

In this study, a fully automated MAM sample preparation protocol is presented, where rapid desalting in less than 15 minutes is achieved using miniaturized size-exclusion chromatography columns in pipette tips on an automated liquid handler. The peptide samples were analyzed using an electrospray ionization (ESI) orbitrap mass spectrometer coupled to an ultra-high-performance liquid chromatography (UHPLC) system with a dual column switching system.

Results

No significant change was observed in product attributes and their quantities compared with manual, low-artifact sample preparation. The sample recovery using the buffer exchange tips was greatly enhanced over the manual spin cartridges while still demonstrating excellent reproducibility for a wide variety of starting sample concentrations. Unlike a plate desalting system, the individual columns provide flexibility in the number of samples prepared at a time and sample locations within plates.

Conclusions

This automated protocol enables the preparation of up to 96 samples with less “at-bench” time than the manual preparation of a smaller batch of samples, thereby greatly facilitating support of process development and the use of the MAM in quality control.