Formation of Supramolecular Nanostructures through in Situ Self-Assembly and Post-Assembly Modification of a Biocatalytically Constructed Dipeptide Hydrazide**

Aqueous self-assembly of short peptides has attracted growing attention for the construction of supramolecular materials for various bioapplications. Herein, we describe how the thermolysin-assisted biocatalytic construction of a dipeptide hydrazide from an N-protected amino acid and an amino acid hydrazide leads to the formation of thermally stable supramolecular hydrogels. In addition, we demonstrate the post-assembly modification of the supramolecular architectures constructed in situ tethering hydrazide groups as a chemical handle by means of fluorescence imaging.     

pH-Sensitive Oscillatory Motion of a Urease Motor on the Urea Aqueous Phase

A self-propelled object coupled with an enzyme reaction between urease and urea was investigated at the air/aqueous interface. A plastic object that was fixed to a urease-immobilized filter paper was used as a self-propelled object, termed a urease motor, placed on an aqueous urea solution. The driving force of the urease motor is the difference in the surface tension around the object. Oscillatory motion or no motion was triggered depending on the initial pH of the urea solution. Both the frequency and maximum speed of the oscillatory motion varied depending on the initial pH of the water phase. The mechanisms underlying the oscillatory motion and no motion were discussed in relation to the bell-shaped enzyme activity of urease in the enzyme reaction and the surface tension around the urease motor.     

Vacuum‐driven fluid manipulation by a piezoelectric diaphragm micropump for microfluidic droplet generation with a rapid system response time

Recently, we developed a convenient microfluidic droplet generation device based on vacuum‐driven fluid manipulation with a piezoelectric diaphragm micropump. In the present study built on our previous work, we investigate the influence of settings applied to the piezoelectric pump, such as peak‐to‐peak drive voltage (V_p‐p) and wave frequency, on droplet generation characteristics. Stepwise adjustments to the drive voltage in ±10‐V_p‐p increments over the range of 200?250 V_p‐p during droplet creation revealed that the droplet generation rate could be reproducibly controlled at a specific drive voltage. The droplet generation rate switched within <0.5 s after the input of a new voltage. Although the droplet generation rate depended on the drive voltage, this setting had almost no influence on droplet size. The frequency over the selected range (50?60 Hz) did not markedly influence the droplet generation rate or droplet size. We show that the current fluid manipulation system can be conveniently used for both droplet generation and for rapid droplet reading, which is required in many microfluidic‐based applications.     

Extended Open-Chain Polyenides as Versatile Delocalized Anion Ligands for Metal Chain Clusters

Although small cyclic- and open-chain unsaturated hydrocarbon anions such as cyclopentadienide and open-chain pentadienide are used as the strongly electron-donating auxiliary ligands for metal complexes, more extended π-conjugated unsaturated hydrocarbon anions have rarely been used in coordination chemistry, despite their potential ability to serve as the multiply bridging π-ligands for metal clusters. This work reports isolation of metal chain clusters bearing the multi-dentate, open-chain extended unsaturated hydrocarbon anion ligands. The extended open-chain π-conjugated polyenyl ligands could effectively stabilize oxidized palladium chains, including an unprecedented [Pd₄]⁴⁺ chain.     

Silicon-Based Integrated Optic Pressure Sensor Using Intermodal Interference between TM-Like and TE-Like Modes

In this paper, a silicon-based integrated optic pressure sensor using an intermodal interference between the fundamental TM-like and TE-like modes is described. The sensor consists of a micromachined rectangular diaphragm and a straight polystyrene optical waveguide passing over the diaphragm. Its sensitivity is theoretically known to be strongly dependent on the position of the waveguide over the diaphragm. To experimentally investigate such dependence, we fabricated a sensor with a 1.2 mm ×10 mm ×20 μm diaphragm, over which waveguides were placed at 50 μm intervals. The measured phase sensitivity was 98 mrad/kPa for the waveguide nearest to the diaphragm edge. The measurement was also carried out for the other waveguides. As theoretically expected, the largest sensitivity was obtained for the waveguide nearest to the edge.     

Stable all-optical formation of Bose–Einstein condensate using pointing-stabilized optical trapping beams

By stabilizing the beam pointing of optical trapping beams, we have succeeded in stable formation of Bose–Einstein condensate (BEC) of ⁸⁷Rb with all-optical method. The thermal effect of acousto-optic modulator (AOM) is usually one of the most serious problems to induce beam-pointing instability, especially for high power CO₂ laser. By passing the beam through AOM twice, we have improved the beam pointing from about 4.8 mrad to less than 0.4 mrad, which has been experimentally confirmed to be small enough to stably form BEC at the crossed region of CO₂ lasers as well as to perform experiments using an optical lattice which might have been affected by beam-pointing instability. PACS 32.80.Pj; 42.79.Jq; 03.75.Mn     

Convenient synthesis of alkoxyhalosilanes from hydrosilanes

Selective dehydrogenative coupling of di- and trihydrosilanes with alcohols catalyzed by PdCl₂ or NiCl₂ afforded alkoxyhydro- and dialkoxyhydrosilanes in good yield. Further treatment of the resulting alkoxyhydrosilanes with carbon tetrachloride or allyl bromide in the presence of the same catalyst led to the formation of alkoxychloro- and alkoxybromosilanes, respectively. Similar reactions of dialkoxyhydrosilanes with carbon tetrachloride afforded dialkoxychlorosilanes in good yield, although contamination of small amounts of trialkoxysilanes and alkoxydichlorosilanes was detected in the products. Selective substitution of the alkoxyhalosilanes with nucleophiles is also reported.     

Application of total reflection X-ray fluorescence spectrometry to small glass fragments.

Total reflection X-ray fluorescence spectrometry (TXRF) has been applied for trace elemental analysis of small glass fragments. A small glass sample (a fragment with weight less than 0.5 mg) was decomposed by 100 microg of HF/HNO3 acid; the material was condensed to 10 microl and was dried on a Si wafer. Since the size of the dried residue on the Si wafer was less than 1 cm in diameter, an incident X-ray beam with about 1 cm in width could effectively excite elemental components in such a small glass fragment. The precision of the present technique was checked by analyzing the glass fragments (<0.5 mg) from NIST SRM612; the relative standard deviations (RSD) of less than 8.1% were achieved for elemental ratios that were normalized by Sr. Fragments (<0.5 mg) obtained from 23 figured sheet glasses were used as samples for estimating the utility of this technique to forensic discrimination. Comparison of five elemental ratios of Ti/Sr, Mn/Sr, Zn/Sr, Rb/Sr, and Pb/Sr calculated from X-ray fluorescence spectra was effective in distinguishing glass fragments that could not be differentiated by their refractive indexes (RI).     

Combinatorial computational chemistry approach of tight-binding quantum chemical molecular dynamics method to the design of the automotive catalysts

Recently, we have developed a new tight-binding quantum chemical molecular dynamics program “Colors” for combinatorial computational chemistry approach. This methodology is based on our original tight-binding approximation and realized over 5000 times acceleration compared to the conventional first-principles molecular dynamics method. In the present study, we applied our new program to the simulations on various realistic large-scale models of the automotive three-way catalysts, ultrafine Pt particle/CeO₂(111) support. Significant electron transfer from the Pt particle to the CeO₂(111) surface was observed and it was found to strongly depend on the size of the Pt particle. Furthermore, our simulation results suggest that the reduction of the Ce atom due to the electron transfer from the Pt particle to the CeO₂ surface is a main reason for the strong interaction of the Pt particle and CeO₂(111) support.