Fibre raman amplifier properties for applications to long-distance optical communications

This paper reviews recent theoretical and experimental studies on optical amplification by stimulated Raman scattering (Raman amplification) in single-mode optical fibres, and discusses its possible applications to long-distance optical communications. The fibre Raman amplifier can be used as an in-line optical amplifier in both repeaterless and non-regenerative all-optical repeater configurations. In the former application, signal transmission of over 400 km has been predicted theoretically, although high-power pump sources are considered to be required. In the latter configuration, in which optical fibre losses are compensated for by Raman gains, it has been shown that extremely long-distance transmission over more than 1000 km is feasible in terms of signal-to-noise ratio, where the distance achievable is mainly limited by the accumulation of Raman noise. Recent experimental demonstrations including bit-error rate measurements on the Raman amplified signal, and laser-diode pumped amplification, etc., are also reviewed. The results confirm the effectiveness of fibre Raman amplifiers in future long-haul systems.     

‘Me2CuLi·TMSCl in CH2Cl2’. The most powerful methylating agent for sterically congested α,β-enoates

The reaction of Me₂CuLi with sterically congested α,β-unsaturated esters in the presence of TMSCl in CH₂Cl₂ proceeded very smoothly to produce the conjugate addition products in high yields.     

Developing a hybrid emulsion polymerization system to synthesize Fe3O4/polystyrene latexes with narrow size distribution and high magnetite content

A hybrid emulsion polymerization was formulated for synthesizing Fe₃O₄/polystyrene composite latex. This system, containing binary droplets that are magnetic (Mag)‐droplets with a diameter of 100–200 nm and styrene (St)‐droplets with a diameter of 3–4 μm, was obtained by mixing Mag‐miniemulsion and St‐macroemulsion. With extremely low surfactants concentration (?critical micelle concentration, CMC), the nucleated loci are selectively controlled in the Mag‐droplets, as the result of smaller droplet size and larger surface ratio. Both water‐soluble potassium persulfate (KPS) and oil‐soluble 2,2′‐azobis(2‐isobutyronitrile) was adopted to initiate the polymerization. In the presence of KPS, magnetic polystyrene latices with particles size of 60–200 nm, narrow size distribution, and high magnetite content (86 wt % measured by TGA) were attained successfully. The synthesized magnetic Fe₃O_4/polystyrene latices assembled into well‐ordered hexagonal structure in the surface of a carbon supported copper grid. The influence of various parameters on various aspects of the as‐synthesized Fe₃O₄/polystyrene was investigated in detail: type of initiator on composite morphology, feed ratio of Mag‐miniemulsion and St‐macroemulsion on magnetite content, and hydrophobic agent or amount of surfactant on size and size distribution. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5285–5295, 2007     

Fabrication and transport properties of multiwall carbon nanotube crossroads

A multiwall carbon nanotube crossroads has been fabricated by a manipulation technique using a glass microcapillary, and the low temperature transport properties investigated. The two-terminal conductance of an individual tube shows Tomonaga–Luttinger liquid behavior G∝T^α at high temperature and dI/dV ∝V ^α at low temperature. However, no evidence of such a power-law behavior is obtained in the four-terminal conductance at the junction, where the conductance shows an almost metallic behavior ‘corrected’ by weak localization. Weak localization would essentially appear in electron states at the junctions of MWNTs.     

Argon sorption and partial molar volume in poly(ethyl methacrylate) above and below the glass transition temperature

Sorption and dilation isotherms for argon in poly(ethyl methacrylate) (PEMA) are reported for pressures up to 50 atm over the temperature range 5–85°C. At temperatures below the glass transition (T_g=61°C), sorption isotherms are well described by the dual-mode sorption model; and isotherms above T_g follow Henry's law. However, isotherms for dilation due to sorption are linear in pressure at all temperatures over the range investigated. Partial molar volumes of Ar in PEMA are obtained from these isotherms. The volumes are approximately constant above T_g (about 40 cm³/mol), whereas the volumes below T_g are smaller and dependent on both temperature and concentration (19–26 cm³/mol). By analyzing the experimental data according to the dual-mode sorption and dilation model, the volume occupied by a dissolved Ar molecule and the mean size of microvoid in the glass are estimated to be 67 129 ų, respectively. The cohesive energy density of the polymer is also estimated as 61 cal/cm³ from the temperature dependence of the dual-mode parameters.     

Dicationic ((−)-sparteine)palladium-catalyzed enantioselective aldol reaction of aldehydes with 1-phenyl-1-trimethylsilyloxyethene, proceeding via a palladium enolate

A dicationic ((−)-sparteine)palladium complex underwent a superior catalytic enantioselective aldol reaction of aldehydes with 1-phenyl-1-trimethylsilyloxyethene performing satisfactorily, starting with ((−)-sparteine)PdCl₂ and AgSbF₆ as catalyst precursors (1 mol % loading) in the presence of 3 Å molecular sieves over the reaction.     

A convergent approach to the formal total synthesis of hemibrevetoxin B

A convergent synthesis of the key synthetic intermediate of hemibrevetoxin B was achieved via the intramolecular allylation of an α-chloroacetoxy ether and subsequent ring-closing metathesis.     

Application of total reflection X-ray fluorescence spectrometry to small glass fragments.

Total reflection X-ray fluorescence spectrometry (TXRF) has been applied for trace elemental analysis of small glass fragments. A small glass sample (a fragment with weight less than 0.5 mg) was decomposed by 100 microg of HF/HNO3 acid; the material was condensed to 10 microl and was dried on a Si wafer. Since the size of the dried residue on the Si wafer was less than 1 cm in diameter, an incident X-ray beam with about 1 cm in width could effectively excite elemental components in such a small glass fragment. The precision of the present technique was checked by analyzing the glass fragments (<0.5 mg) from NIST SRM612; the relative standard deviations (RSD) of less than 8.1% were achieved for elemental ratios that were normalized by Sr. Fragments (<0.5 mg) obtained from 23 figured sheet glasses were used as samples for estimating the utility of this technique to forensic discrimination. Comparison of five elemental ratios of Ti/Sr, Mn/Sr, Zn/Sr, Rb/Sr, and Pb/Sr calculated from X-ray fluorescence spectra was effective in distinguishing glass fragments that could not be differentiated by their refractive indexes (RI).     

Local structure analysis of smoky and colorless topaz using single crystal Al NMR

The angular dependence of the ²⁷Al NMR spectrum was measured for single crystals of smoky and colorless topaz, Al₂SiO₄(F,OH)₂. Smoky topaz was obtained by irradiating high energy neutrons to colorless topaz. The quadrupole coupling constant e²Qq/h and the asymmetry parameter η were obtained from the analysis of the angular dependences of quadrupole splitting of the ²⁷Al NMR spectrum. The local structures around the aluminum atoms in smoky and colorless topaz were discussed from the magnitude and the direction of the electric field gradient. The directions of principal axes of the EFG tensor of ²⁷Al were close to the directions of Al-O and Al-F bonds. The difference in the bond lengths between Al(1)-F(1) and Al(1)-F(2) was found to affect the x and y components of the EFG tensor.