Portable single-sided NMR measurements at variable temperatures: Implementation of a thermo-controlled device and application to the heating of bread dough

A temperature control unit was implemented to vary the temperature of samples studied on a commercial Mobile Universal Surface Explorer nuclear magnetic resonance (MOUSE-NMR) apparatus. The device was miniaturized to fit the maximum MOUSE sampling depth (25 mm). It was constituted by a sample holder sandwiched between two heat exchangers placed below and above the sample. Air was chosen as the fluid to control the temperature at the bottom of the sample, at the interface between the NMR probe and the sample holder, in order to gain space. The upper surface of the sample was regulated by the circulation of water inside a second heat exchanger placed above the sample holder. The feasibility of using such a device was demonstrated first on pure water and then on several samples of bread dough with different water contents. For this, T1 relaxation times were measured at various temperatures and depths and were then compared with those acquired with a conventional compact closed-magnet spectrometer. Discussion of results was based on biochemical transformations in bread dough (starch gelatinization and gluten heat denaturation). It was demonstrated that, within a certain water level range, and because of the low magnetic field strength of the MOUSE, a linear relationship could be established between T1 relaxation times and the local temperature in the dough sample.     

Thermal management of modern electric vehicle battery systems (MEVBS)

Journal of Thermal Analysis and Calorimetry - The operating temperature of Li-ion batteries used in modern electric vehicles should be maintained within an allowable range to avoid thermal runaway...     

Estimation of growth rate in unidirectionally solidified multicrystalline silicon by the growth-induced striation method

Multicrystalline silicon was grown by unidirectional solidification method using the accelerated crucible rotation technique. The application of the accelerated crucible rotation technique in unidirectional solidification method induced growth striations across the axial direction of the grown crystal. This striation pattern was observed from carbon concentration distribution, obtained by using Fourier transform infrared spectroscopy. The generated striation pattern was found to be weak and discontinuous. Some striations were absent, probably due to back melting, caused during each crucible rotation. From the growth striations and applied time period in crucible rotation, the growth rate was estimated by using Fourier transformation analysis.     

Integral Representations,Differentiability Properties and Limits at Infinity for Beppo Levi Functions

The first aim in the present paper is to give an integral representation for Beppo Levi functions on R ⁿ. Our integral representation is an extension of Sobolev's integral representation given for infinitely differentiable functions with compact support. As applications, continuity and differentiability properties of Beppo Levi functions are studied.Our second aim in this paper is to study the existence of limits at infinity for Beppo Levi functions. We also consider the existence of fine-type limits at infinity with respect to Bessel capacities, which yields the radial limit result at infinity.     

Some inequalities for the polar derivative of a polynomial

LetP(z) be a polynomial of degreen which does not vanish in |z|<1. In this paper, we estimate the maximum and minimum moduli of thekth polar derivative ofP(z) on |z|=1 and thereby obtain compact generalizations of some known results, which among other results, yields interesting refinements of Erdos-Lax theorem and a theorem of Ankeny and Rivlin.     

Complex impedance spectra of chip inductor using Li–Zn–Cu–Mn ferrite

A multi-layer chip inductor (MCI) was fabricated using polycrystalline Li–Zn–Cu–Mn ferrite and the green-sheet technique, and its complex impedance spectrum was evaluated with the help of numerical calculations. The complex impedance spectra of the MCI component using Ni–Zn–Cu ferrite, which have been widely used for this application, were very sensitive to the residual stress and deviated much from the calculated values; however, it was found that the complex impedance spectrum of the MCI component using Li–Zn–Cu–Mn ferrite is quite well reproduced by calculation, where the complex permittivity and permeability of the polycrystalline ferrite as well as the MCI dimensions, were used. It implied that the magneto-striction effect was negligible in case of MCI using Li–Zn–Cu–Mn ferrite, and that the difference was related to magneto-strictive coefficient of the polycrystalline ferrite. Consequently, utilization of Li–Zn–Cu–Mn ferrite enabled us to easily design the complex impedance of MCI component.     

Numerical calculations of temperature distribution of double layer metallic surface treated by laser beams

A mathematical model of laser beam treatment of double layer alloys (Ni/Fe, Al/Fe and Cr/Fe systems) describing the effect of laser beam on different physical and geometrical parameters of coated layer system has been adapted. The numerical solutions of the non-homogeneous heat-transport differential equation could estimate the temperature of the treated region.The suggested model allows investigation of the temperature distribution as a function of treated surface and laser parameters. The physical parameters of the treated materials were taken as functions of temperature due to the change in the temperature of the treated double layer materials.     

Hydrolysis of acetals in water under hydrothermal conditions

A simple method for the hydrolysis of acetals and ketals was accomplished in neutral water or aqueous media by hydrothermal treatment without using acidic reagents. The deacetalization reaction was effectively accelerated in the presence of calcium chloride. Because no acidic catalysts were employed, neutralization of the reaction mixture was not necessary after the reaction. This sequence was successfully applied to the hydrolysis of chitosan, a biodegradable polyaminosaccharide.     

On self-reciprocal polynomials

In this paper we establish a sharp result concerning integral mean estimates for self-reciprocal polynomials.