Estimation of growth rate in unidirectionally solidified multicrystalline silicon by the growth-induced striation method

Multicrystalline silicon was grown by unidirectional solidification method using the accelerated crucible rotation technique. The application of the accelerated crucible rotation technique in unidirectional solidification method induced growth striations across the axial direction of the grown crystal. This striation pattern was observed from carbon concentration distribution, obtained by using Fourier transform infrared spectroscopy. The generated striation pattern was found to be weak and discontinuous. Some striations were absent, probably due to back melting, caused during each crucible rotation. From the growth striations and applied time period in crucible rotation, the growth rate was estimated by using Fourier transformation analysis.     

Integral Representations,Differentiability Properties and Limits at Infinity for Beppo Levi Functions

The first aim in the present paper is to give an integral representation for Beppo Levi functions on R ⁿ. Our integral representation is an extension of Sobolev's integral representation given for infinitely differentiable functions with compact support. As applications, continuity and differentiability properties of Beppo Levi functions are studied.Our second aim in this paper is to study the existence of limits at infinity for Beppo Levi functions. We also consider the existence of fine-type limits at infinity with respect to Bessel capacities, which yields the radial limit result at infinity.     

Complex impedance spectra of chip inductor using Li–Zn–Cu–Mn ferrite

A multi-layer chip inductor (MCI) was fabricated using polycrystalline Li–Zn–Cu–Mn ferrite and the green-sheet technique, and its complex impedance spectrum was evaluated with the help of numerical calculations. The complex impedance spectra of the MCI component using Ni–Zn–Cu ferrite, which have been widely used for this application, were very sensitive to the residual stress and deviated much from the calculated values; however, it was found that the complex impedance spectrum of the MCI component using Li–Zn–Cu–Mn ferrite is quite well reproduced by calculation, where the complex permittivity and permeability of the polycrystalline ferrite as well as the MCI dimensions, were used. It implied that the magneto-striction effect was negligible in case of MCI using Li–Zn–Cu–Mn ferrite, and that the difference was related to magneto-strictive coefficient of the polycrystalline ferrite. Consequently, utilization of Li–Zn–Cu–Mn ferrite enabled us to easily design the complex impedance of MCI component.     

Hydrolysis of acetals in water under hydrothermal conditions

A simple method for the hydrolysis of acetals and ketals was accomplished in neutral water or aqueous media by hydrothermal treatment without using acidic reagents. The deacetalization reaction was effectively accelerated in the presence of calcium chloride. Because no acidic catalysts were employed, neutralization of the reaction mixture was not necessary after the reaction. This sequence was successfully applied to the hydrolysis of chitosan, a biodegradable polyaminosaccharide.     

Design of a widely tunable laser with a chirped ladder filter

We theoretically investigated a digitally tunable laser with a chirped ladder filter and a ring resonator to obtain a wide wavelength tuning range covering the whole C- or L- band. The clear relation between the tuning range and laser structure, especially the ladder filter, is described analytically. The introduction of a chirped structure into a ladder filter is effective in achieving both wide tunability and a stable lasing mode. A numerical simulation based on multimode rate equations shows that a tuning range of over 40 nm and a mode suppression ratio over 40 dB can be achieved by introducing a chirped ladder filter.     

Improved coating method for uniform polymer layer in infrared hollow fiber

An improved coating method was proposed in order to form a uniform polymer layer in the fabrication of cyclic olefin polymer-coated silver (COP/Ag) hollow fiber. A COP solution was flowed in a closed loop, in which the silver-coated tube was used as a part of the loop. Owing to the constant flowing speed of the COP solution and the airtight flowing environment, a COP layer was uniformly formed. The hollow fibers attain high performance and deliver multi-wavelength laser light from the infrared to the visible simultaneously. The method was successfully applied to the fabrication of practical hollow fibers with 2 m length for the near and mid-infrared lasers.     

Fiber-in-Tube Solid Phase Extraction (FIT-SPE) for Miniaturized Sample Preparation Process

A typical analytical separation procedure has several important steps: sample preparation, isolation, identification, quantitation, statistical evaluation and final decision. Each step is alwayscritical to obtain correct results to fulfill the analytical purpose. In these various steps sample     

Electrochiroptical systems based on biphenyl-2,2′-diyl-type dicationic dyes: strong chiroptical signals through the transmission of point chirality to axial chirality

Huge CD amplitude (A = +538) was attained by diastereomeric preference (50% de) for the title dication with two bis[4-(R)-sec-butoxyphenyl]methylium units in benzene at 23 °C. Intramolecular π-π stacking is the origin for effective transmission of point chirality to axial chirality to attain the chiroptical enhancement of 400-times. Thanks to the strong CD signaling, chiroptical changes upon electrolysis could be readily detected, thus realizing a new class of electrochiroptical response systems. Chiroptical properties could also be modified by solvent polarity.     

Stereo- and regio-selective formation of 2-oxazolone telomers as potential synthetic intermediates for aminosugars

3-Acetyl-2-oxazolone readily undergoes free-radical homopolymerization as well as telomerization with polyhalomethanes, in which low telomer formation is highly stereo- and regio-selective.