The polar ionosphere at Zhongshan station on May 11, 1999, the day the solar wind almost disappeared

The solar wind almost disappeared on May 11, 1999: the solar wind plasma density and dynamic pressure were less than 1cm⁻³ and 0.1 nPa respectively, while the interplanetary magnetic field was northward. The polar ionospheric data observed by the multi-instruments at Zhongshan Station in Antarctica on such special event day was compared with those of the control day (May 14). It was shown that geomagnetic activity was very quiet on May 11 at Zhongshan. The magnetic pulsation, which usually occurred at about magnetic noon, did not appear. The ionosphere was steady and stratified, and the F₂ layer spread very little. The critical frequency of day-side F₂ layer, f₀F₂, was larger than that of control day, and the peak of f₀F₂ appeared 2 hours earlier. The ionospheric drift velocity was less than usual. There were intensive auroral E_s appearing at magnetic noon. All this indicates that the polar ionosphere was extremely quiet and geomagnetic field was much more dipolar on May 11. There were some signatures of auroral substorm before midnight, such as the negative deviation of the geomagnetic H component, accompanied with auroral E_s and weak Pc3 pulsation.

     

Large set of P3‐decompositions

Let G=(V(G),E(G)) be a graph. A (n,G, λ)‐GD is a partition of the edges of λK_n into subgraphs (G‐blocks), each of which is isomorphic to G. The (n,G,λ)‐GD is named as graph design for G or G‐decomposition. The large set of (n,G,λ)‐GD is denoted by (n,G,λ)‐LGD. In this work, we obtain the existence spectrum of (n,P₃,λ)‐LGD. © 2002 Wiley Periodicals, Inc. J Combin Designs 10: 151–159, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/jcd.10008     

光纤白光干涉仪等臂长技术研究

介绍了几种光纤干涉仪等臂长技术,比较了各自的优缺点和适用范围,对光纤干涉仪的平衡有较大的参考价值。     

非傍轴平顶高斯光束M2因子两种定义的比较研究

基于功率密度的二阶矩方法,推导出了非傍轴平顶高斯(FG)光束束宽和远场发散角的解析表达式·研究表明,当w0/λ→0时,远场发散角趋于渐近值θmax=63.435°,与阶数无关·使用非傍轴高斯光束代替傍轴高斯光束作为理想光束,研究了非傍轴FG光束的M2因子,并与传统定义的M2因子作了比较·在非傍轴范畴,非傍轴FG光束的M2因子不仅与阶数N有关,而且与w0/λ有关·按照定义,当w0/λ→0时,非傍轴FG光束的M2因子不等于0,对阶数N=1,2,3时,M2因子分别趋于0.913,0.882和0.886·当N→∞时,M2因子取最小值M2min=0.816·     

SiOx纳米管的制备及其发光特性

以液态金属镓为媒介,利用热蒸发法合成大量非晶SiOx纳米管,这些纳米管管径均匀分布,平均约80 nm,长度大于10μm,且管内外径比例较小．分析发现,在实验过程中,熔入金属镓液滴中的硅元素和氧元素结合并从液滴的表面饱和析出,形成以镓为中心的非晶SiOx纳米管状结构．在室温中,利用260 nm的激发光源激发SiOx纳米管,发现在蓝光波段附近发出强而稳定的PL谱线,这可能与样品中的氧缺陷和空位有关．     

Fiber-optic reflex sensor for in-line production measurement

The paper describes experiments concerning distance measurement with fiber-optic sensor and improvement of the measurement principle. The sensor probe was well-designed with a small structure and multi-function. The novel optical fiber probe arrangement as well as the possibilities of use for complex measurement problems are explained using the measurement of an internal screw thread as an example. The experimental results show that the measurement uncertainty of the thread minor diameter can reach ±10 μm, and the stability of the measurement system is better than 0.07%.     

Efficient microwave induced direct α-halogenation of carbonyl compounds

A novel and direct method for the synthesis of α-halocarbonyl compounds using sequential treatment of carbonyl compounds with [hydroxy(tosyloxy)iodo]benzene followed by magnesium halides under solvent-free microwave irradiation conditions is described.     

The Design for Automation of Pellet-Forming Process in HL-2A Pellet Fueling System

In the ever fusion experiments in SWIP, pellet forming process was carried out through adjusting relative devices by staff member in site, which will make every pellet-forming process slight distinction and will result in pellet difference in shape, size and intensity. In the intervals of HL-2A discharges, staff member have to go site to accomplish the pellet-forming process, this wastes human power and increase the potential danger. So it is necessary to develop a remote control system to perform the pellet-forming process. The control system needs have the features of real-time, reliability and be easy to operate and maintain.