Colour quenching corrections on the measurement of 90Sr through Cerenkov counting

The determination of ⁹⁰Sr through the Cerenkov radiation emitted by its descendant ⁹⁰Y is a well-known method and firmly established in literature. Nevertheless, in order to obtain an accurate result based on a Cerenkov measurement, the experimental work must be extremely rigorous because the efficiency of Cerenkov counting is especially sensitive to the presence of colour. Any traces of colour in the sample produce a decrease in the number of photons detected in the photomultipliers and, therefore, this might cause a diminution in Cerenkov counting efficiency. It is essential not only to detect the effect of colour quenching in the sample but also to correct the decrease in counting efficiency. For this reason, colour quenching correction curves versus counting efficiency are usually done when measuring through Cerenkov counting. One of the most widely used techniques to evaluate colour quenching in these measurements is the channel ratio method, which consists of the measurement of the shift of the spectrum measuring the ratio of counts in two different windows. The selection of the windows for the application of the corrections might have an influence on the quality of the fitting parameters of the correction curves efficiency versus colour quenching degree and hence on the final ⁹⁰Sr result. This work is focused on the calculation of the counting efficiency decrease using the channel ratio method and on obtaining the best fitting correction curve. For this purpose, empirical curves obtained through artificial quenchers have been studied and the results have been tested in real samples. Additionally, given that the Packard Tri-Carb 3170 TR/SL liquid scintillation counter is a novel detector for use in Cerenkov counting, the previous calibration of the Tri-Carb 3170 TR/SL detector, necessary for the measurement of ⁹⁰Sr, is included.     

Electrical characterization of poly(ethylene oxide)–clay nanocomposites prepared by microwave irradiation

Poly(ethylene oxide) (PEO)–clay (montmorillonite, hectorite, and laponite) nanocomposites were prepared by a melting intercalation procedure induced by microwave irradiation. The influence of parameters such as the time of irradiation, power, amount and relative ratio of the reagents, and relative humidity was investigated. X-ray diffraction, differential scanning calorimetry, elemental microanalysis, Fourier transform infrared, and scanning electron microscopy techniques were applied to characterize the resulting nanocomposites. Techniques involving impedance spectroscopy, thermoelectric power, and electrical polarization in the solid state were used to characterize the electrical properties of the nanocomposites. The electrical behavior of these PEO–silicate nanocomposites, including those containing an excess of alkaline metal salts in comparison with that of similar systems prepared by alternative procedures such as direct intercalation from polymer solutions or melting intercalation, was also examined. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3249–3263, 2003     

Preparation and characterization of LiNi0.8Co0.2O2/PANI microcomposite electrode materials under assisted ultrasonic irradiation

A preparation method for a new electrode material based on the LiNi_0.8Co_0.2O₂/polyaniline (PANI) composite is reported. This material is prepared by in situ polymerization of aniline in the presence of LiNi_0.8Co_0.2O₂ assisted by ultrasonic irradiation. The materials are characterized by XRD, TG-DTA, FTIR, XPS, SEM-EDX, AFM, nitrogen adsorption (BET surface area) and electrical conductivity measurements. PANI in the emeraldine salt form interacts with metal-oxide particles to assure good connectivity. The dc electrical conductivity measurements at room temperature indicate that conductivity values are one order of magnitude higher in the composite than in the oxide alone. This behavior determines better reversibility for Li-insertion in charge-discharge cycles compared to the pristine mixed oxide when used as electrode of lithium batteries.     

Determination of major, minor and trace elements in cobalt-substituted lithium nickelate ceramic powders by inductively coupled plasma optical emission spectrometry

An analytical method was developed for the determination of three major (Li, Ni and Co) and fourteen minor or trace elements (Al, Ba, Ca, Cu, Cr, Fe, K, Mg, Mn, Na, Si, Sr, Ti and V) in LiNi_1−x Co _x O₂ (x = 0.2–0.8) ceramic powders by inductively coupled plasma optical emission spectrometry. Sample dissolution was achieved by 25% nitric acid digestion in a microwave oven. For each element, an analytical line free from spectral interferences was selected. A detailed study of matrix effects over a wide interval of total excitation energy (TEE) lines (1.62–16.50 eV) was performed at near-robust plasma conditions. A remarkable enhancement in atomic lines with TEE <4 eV was noticed, whereas a significant reduction in atomic and ionic lines with TEE >4 eV was observed. The extrapolation to infinite dilution method was successfully used to overcome these nonspectroscopic interferences. Detection limits (3σ) varied from 0.21 mg kg⁻¹ for Sr to 49.7 mg kg⁻¹ for Na. The precision of determination (obtained as the relative standard deviation) was lower than 1% for the major elements Li, Ni and Co and between 0.69 and 10% for minor and trace elements. The accuracy of the method ranged from 91 to 101% for major elements, and from 90 to 110%, or close to this range, for most of the impurities in both of the samples studied.