The Effect of α-Branched Side Chains on the Structural and Opto-Electronic Properties of Poly(Diketopyrrolopyrrole-alt-Terthiophene)

Introducing solubilizing α-branched alkyl chains on a poly(diketopyrrolopyrrole-alt-terthiophene) results in a dramatic change of the structural, optical, and electronic properties compared to the isomeric polymer carrying β-branched alkyl side chains. When branched at the α-position the alkyl substituent creates a steric hindrance that reduces the tendency of the polymer to π–π stack and endows the material with a much higher solubility in common organic solvents. The wider π–π stacking and reduced tendency to crystallize, evidenced from grazing-incidence wide-angle X-ray scattering, result in a wider optical band gap in the solid state. In solar cells with a fullerene acceptor, the α-branched isomer affords a higher open-circuit voltage, but an overall lower power conversion efficiency as a result of a too well-mixed nanomorphology. Due its reduced π–π stacking, the α-branched isomer fluoresces and affords near-infrared light-emitting diodes emitting at 820 nm.     

Controlling the Microstructure of Conjugated Polymers in High‐Mobility Monolayer Transistors via the Dissolution Temperature

It remains a challenge to precisely tailor the morphology of polymer monolayers to control charge transport. Herein, the effect of the dissolution temperature (T_dis) is investigated as a powerful strategy for morphology control. Low T_dis values cause extended polymer aggregation in solution and induce larger nanofibrils in a monolayer network with more pronounced π–π stacking. The field‐effect mobility of the corresponding monolayer transistors is significantly enhanced by a factor of four compared to devices obtained from high T_dis with a value approaching 1 cm² V^?1 s^?1. Besides that, the solution kinetics reveal a higher growth rate of aggregates at low T_dis, and filtration experiments further confirm that the dependence of the fibril width in monolayers on T_dis is consistent with the aggregate size in solution. The generalizability of the T_dis effect on polymer aggregation is demonstrated using three other conjugated polymer systems. These results open new avenues for the precise control of polymer aggregation for high‐mobility monolayer transistors.     

Looped structure of flowerlike micelles revealed by 1H NMR relaxometry and light scattering

We present experimental proof that so-called "flowerlike micelles" exist and that they have some distinctly different properties compared to their "starlike" counterparts. Amphiphilic AB diblock and BAB triblock copolymers consisting of poly(ethylene glycol) (PEG) as hydrophilic A block and thermosensitive poly(N-isopropylacrylamide) (pNIPAm) B block(s) were synthesized via atom transfer radical polymerization (ATRP). In aqueous solutions, both block copolymer types form micelles above the cloud point of pNIPAm. Static and dynamic light scattering measurements in combination with NMR relaxation experiments proved the existence of flowerlike micelles based on pNIPAm(16kDa)-PEG(4kDa)-pNIPAm(16kDa) which had a smaller radius and lower mass and aggregation number than starlike micelles based on mPEG(2kDa)-pNIPAm(16kDa). Furthermore, the PEG surface density was much lower for the flowerlike micelles, which we attribute to the looped configuration of the hydrophilic PEG block. (1)H NMR relaxation measurements showed biphasic T(2) relaxation for PEG, indicating rigid PEG segments close to the micelle core and more flexible distal segments. Even the flexible distal segments were shown to have a lower mobility in the flowerlike micelles compared to the starlike micelles, indicating strain due to loop formation. Taken together, it is demonstrated that self-assemblies of BAB triblock copolymers have their hydrophilic block in a looped conformation and thus indeed adopt a flowerlike conformation.     

Photoelastic determination of stresses in multiple-pin connectors

The design, fabrication, and testing of photoelastic models of double-lap, multiple-pin connectors are discussed. Interest is in the stresses in the inner laps. These stresses are determined by constructing models with photoelastic inner laps and transparent-acrylic outer laps. The connectors have two pins, in tandem, parallel to the load direction. A photoelastic-isotropic point is shown to permit the evaluation of load sharing between the two pins. A numerical scheme, utilizing the isochromatic- and isoclinic-photoelastic data and a finite-difference representation of the planestress equilibrium equations, is used to compute the stresses around the two pins. Representative stress distributions and stress-concentration factors are shown.     

A critical investigation of the effects of the radio frequency potential on the trapping of externally injected ions in ion trap mass spectrometry

The sensitivity of all ion trap mass spectrometry (ITMS) methods is dependent on the trapping efficiency of the instrument. For ITMS instruments utilizing external ion sources, such as laser desorption, trapping efficiency is known to depend on the phase and amplitude of the radio frequency (RF) potential applied to the ring electrode at the time of ion introduction. It is remarkable that, in a considerable body of literature, no consensus exists regarding the effects of these parameters on the efficacy of trapping externally generated ions. In this paper, a summary of the literature is presented in order to highlight significant discrepancies. New laser desorption ion trap mass spectrometry (LD-ITMS) data are also presented, from which conclusions are drawn in our effort to clarify some of the confusion. Copyright 1999 John Wiley & Sons, Ltd.     

Thieno[3,2-b]thiophene-diketopyrrolopyrrole-containing polymers for high-performance organic field-effect transistors and organic photovoltaic devices

We report the synthesis and polymerization of a novel thieno[3,2-b]thiophene-diketopyrrolopyrrole-based monomer. Copolymerization with thiophene afforded a polymer with a maximum hole mobility of 1.95 cm(2) V(-1) s(-1), which is the highest mobility from a polymer-based OFET reported to date. Bulk-heterojunction solar cells comprising this polymer and PC(71)BM gave a power conversion efficiency of 5.4%.     

The relationship between nanoscale architecture and function in photovoltaic multichromophoric arrays as visualized by Kelvin probe force microscopy

The physicochemical properties of organic (multi)component films for optoelectronic applications depend on both the mesoscopic and nanoscale architectures within the semiconducting material. Two main classes of semiconducting materials are commonly used: polymers and (liquid) crystals of small aromatic molecules. Whereas polymers (e.g., polyphenylenevinylenes and polythiophenes) are easy to process in solution in thin and uniform layers, small molecules can form highly defined (liquid) crystals featuring high charge mobilities. Herein, we combine the two material types by employing structurally well-defined polyisocyanopeptide polymers as scaffolds to precisely arrange thousands of electron-accepting molecules, namely, perylenebis(dicarboximides) (PDIs), in defined chromophoric wires with lengths of hundreds of nanometers. The polymer backbone enforces high control over the spatial location of PDI dyes, favoring both enhanced exciton and charge transfer. When blended with an electron-donor system such as regioregular poly(3-hexylthiophene), this polymeric PDI shows a relative improvement in charge generation and diffusion with respect to monomeric, aggregated PDI. In order to correlate this enhanced behavior with respect to the architecture, atomic force microscopy investigations on the mixtures were carried out. These studies revealed that the two polymers form interpenetrated bundles having a nanophase-segregated character and featuring a high density of contact points between the two different phases. In order to visualize the relationship between the architecture and the photovoltaic efficiency, Kelvin probe force microscopy measurements were carried out on submonolayer-thick films. This technique allowed for the first time the direct visualization of the photovoltaic activity occurring in such a nanoscale phase-segregated ultrathin film with true nanoscale spatial resolution, thus making possible a study of the correlation between function and architecture with nanoscale resolution.