Benzyl alcohol oxidation and hydrogen generation over MoS2/ZnIn2S4 composite photocatalyst

Research on Chemical Intermediates - Owing to the simultaneous utilization of photogenerated electrons and holes, coupling light-driven hydrogen (H2) evolution reaction (HER) and biomass-derived...     

Geometrically nonlinear dynamic analysis of the stiffened perovskite solar cell subjected to biaxial velocity impacts

Nonlinear Dynamics - The perovskite solar cell (PSC) is one of the most promising photovoltaic candidates along with the highly increasing demand for green electricity. One of the main concerns...     

Flower-like titanium dioxide as novel co-reaction accelerator for ultrasensitive “off–on” electrochemiluminescence aptasensor construction based on 2D g-C3N4 layer for thrombin detection

Journal of Solid State Electrochemistry - An ultrasensitive “signal-off–on” electrochemiluminescence (ECL) biosensor is constructed based on f1-TiO2/g-C3N4/PDA for thrombin...     

Development and validation of LC–MS/MS method for amlexanox in rat plasma and its application in preclinical pharmacokinetics

Amlexanox, an anti-inflammatory and anti-allergic agent, has been widely used clinically for the treatment of canker sores, asthma, and allergic rhinitis. Recently, amlexanox has received considerable attention in curing nonalcoholic fatty liver diseases and hepatitis virus infection. Herein, we first established a sensitive high-performance liquid chromatography-tandem mass spectrum (LC–MS/MS) method for the determination of amlexanox in rat plasma. Propranolol was used as the internal standard (IS). Using a simple protein precipitation method, the amlexanox and IS were separated with Capcell Pak C18 column (2.0 × 50 mm, 5 μm) and eluted with water and acetonitrile each containing 0.1% formic acid using gradient elution condition at a flow rate of 0.4 mL·min⁻¹. Amlexanox and IS were detected by a triple quadrupole mass in multiple reactive monitoring (MRM) under the transitions of m/z 299.2 → 281.2 and m/z 259.9 → 116.1 with positive electrospray ionization, respectively. The calibration curves of amlexanox were established with the range of 50 to 2000 ng·mL⁻¹ (r² > 0.99). The validation method consisted of selectivity, accuracy, precision, carryover effect, matrix effect, recovery, dilution effect, and stability. The fully validated method was successfully applied to the pharmacokinetic study of amlexanox in Wistar rats.     

Developing the Low-Temperature Oxidation Mechanism of Cyclopentane: An Experimental and Theoretical Study

At present, the reactivity of cyclic alkanes is estimated by comparison with acyclic hydrocarbons. Due to the difference in the structure of cycloalkanes and acycloalkanes, the thermodynamic data obtained by analogy are not applicable. In this study, a molecular beam sampling vacuum ultraviolet photoionization time-of-flight mass spectrometer (MB-VUV-PI-TOFMS) was applied to study the low-temperature oxidation of cyclopentane (CPT) at a total pressure range from 1–3 atm and low-temperature range between 500 and 800 K. Low-temperature reaction products including cyclic olefins, cyclic ethers, and highly oxygenated intermediates (e. g., ketohydroperoxide KHP, keto-dihydroperoxide KDHP, olefinic hydroperoxides OHP and ketone structure products) were observed. Further investigation of the oxidation of CPT – electronic structure calculations – were carried out at the UCCSD(T)-F12a/aug-cc-pVDZ//B3LYP/6-31+ G(d,p) level to explore the reactivity of O₂ molecules adding sequentially to cyclopentyl radicals. Experimental and theoretical observations showed that the dominant product channel in the reaction of CPT radicals with O₂ is HO₂ elimination yielding cyclopentene. The pathways of second and third O₂ addition – the dissociation of hydroperoxide – were further confirmed. The results of this study will develop the low-temperature oxidation mechanism of CPT, which can be used for future research on accurately simulating the combustion process of CPT.     

Revealing the Effect of Surface Composition on Multiwalled Carbon Nanotubes Supported Pt-Fe Alloy Electrocatalysts for Methanol Oxidation Performance

The designs of efficient and inexpensive Pt-based catalysts for methanol oxidation reaction (MOR) are essential to boost the commercialization of direct methanol fuel cells. Here, the highly catalytic performance PtFe alloys supported on multiwalled carbon nanotubes (MWCNTs) decorating nitrogen-doped carbon (NC) have been successfully prepared via co-engineering of the surface composition and electronic structure. The Pt₁Fe₃@NC/MWCNTs catalyst with moderate Fe³⁺ feeding content (0.86 mA/mg_Pt) exhibits 2.26-fold enhancement in MOR mass activity compared to pristine Pt/C catalyst (0.38 mA/mg_Pt). Furthermore, the CO oxidation initial potential of Pt₁Fe₃@NC/MWCNTs catalyst is lower relative to Pt/C catalyst (0.71 V and 0.80 V). Benefited from the optimal surface compositions, the anti-corrosion ability of MWCNT, strong electron interaction between PtFe alloys and MWCNTs and the N-doped carbon (NC) layer, the Pt₁Fe₃@NC/MWCNTs catalyst presents an improved MOR performance and anti-CO poisoning ability. This study would open up new perspective for designing efficient electrocatalysts for the DMFCs field.     

High-performance nonfused ring electron acceptor with a steric hindrance induced planar molecular backbone

Three nonfused ring electron acceptors (NFREAs) TTC6,TT-C8T and TT-TC8 were purposefully designed and synthesized.The molecular geometry can be adjusted by the steric hindrance of lateral substituents.According to the DFT calculations,from TTC6 to TT-C8T and TT-TC8,planarity of the molecular backbone is gradually improved,accompanying with the enhancing of intramolecular charge transfer effect.As for TT-TC8,the two phenyl substituents are almost perpendicular to the molecular backbone,which endues the acceptor with good solubility and suppresses it to form over-aggregation.Multidirectional regular molecular orientation and closer molecular stacking are formed in TT-TC8 film.As a result,TT-TC8 based devices afford the highest PCE of 13.13%,which is much higher than that of TTC6 (4.41%) and TT-C8T (10.42%) and among the highest PCE values based on NFREAs.     

基于不确定控制理论的最优策略研究

本文在不确定理论的框架下,研究一类带背景状态变量的最优控制模型.在乐观值准则下,利用不确定动态规划的方法,证明了不确定最优性原则,得到最优性方程.作为应用,求解一个固定缴费(DC)型养老金的最优投资策略问题,在乐观值准则下,以工资变量为背景状态变量,建立养老金模型.通过求解不确定最优性方程得到最优投资策略和最优支付率.     

Acridone-Based Host Materials for Green Phosphorescent and Thermally Activated Delayed Fluorescent OLEDs with Low-Efficiency Roll-Offs

By linking the carbazole unit to the nitrogen atom of acridone through phenyl or pyridyl, two compounds, named 10-(4-(9H-carbazol-9-yl)phenyl)acridin-9(10H)-one (AC-Ph-Cz) and 10-(5-(9H-carbazol-9-yl)pyridin-2-yl)acridin-9(10H)-one (AC-Py-Cz) were designed and synthesized. These two materials, characterized with highly twisted and rigid structure, good thermal stability, and balanced carrier-transporting properties, were employed as host materials for green phosphorescent and thermally activated delayed fluorescent organic light-emitting diodes (OLEDs). The carbazole group, despite its small contribution to the highest occupied molecular orbitals (HOMOs) of these two materials, plays an essential role as an intramolecular host in energy delivering and improving the hole transporting ability of these two hosts. The incorporation of the electron-deficient pyridyl group as a linking group slightly improves the electron transporting capability of AC-Py-Cz. The green phosphorescent OLED (PhOLED) based on AC-Py-Cz exhibited excellent device performance with a turn-on voltage of 2.5 V, a maximum power efficiency and an external quantum efficiency (η_ext) of 89.8 lm W⁻¹ and 25.2 %, respectively, benefitting from the better charge-balancing ability of AC-Py-Cz host due to the presence of the pyridyl bridge. More importantly, all the devices based on these two hosts showed low efficiency roll-off at high brightness due to the suppressed non-radiative transition in the emitting layer. In particular, the AC-Py-Cz-hosted green PhOLED exhibited an efficiency roll-off of 1.6 % from the maximum next at a high brightness of 1000 cd m⁻² and a roll-off of 15.9 % at an extremely high brightness of 10000 cd m⁻². This study manifests that acridone-based host materials have great potential in fabricating OLEDs with low efficiency roll-off.