溶胶-凝胶制备技术与新型催化材料Ⅲ.溶胶粒子表面修饰方法制备催化膜

提出用溶胶粒子表面修饰方法，结合溶胶凝胶技术制备无机催化膜．该方法的基本原理是利用合适的金属配合物在胶粒表面的吸附作用，经溶胶凝胶过程，将活性组分结合到无机膜中．实验测定结果表明：（ＮｉＥＤＴＡ）２－，ＶＯ－３，ＭｏＯ２－４，（Ｐｄ（ＮＨ３）４）２＋，ＰｄＣｌ２－４，ＰｔＣｌ２－６和ＲｈＣｌ３－６可用来修饰ＡｌＯＯＨ溶胶．以Ｐｄ／γＡｌ２Ｏ３催化膜的制备为例，经三次溶胶凝胶过程，可制得无裂缺的厚度为９μｍ的Ｐｄ／γＡｌ２Ｏ３催化膜，膜材料的平均孔直径为６ｎｍ，Ｐｄ被均匀地分布在膜的顶层，其平均粒径为２３ｎｍ．     

Three-dimensional atom probe study of the segregation behaviour of Ni91Pt9 alloy after sputtering

To investigate local ordering and segregation phenomenon in a Ni91Pt9-alloy after sputtering and annealing a 3D optical atom probe (OAP) has been used. The specimen tips have been prepared from polycrystalline samples. To sputter the samples a separate preparation chamber with a scannable Ar-sputter-gun is connected to the OAP vessel. When necessary, the sample can be electrically heated to induce segregation and cure the altered layer. After a heat treatment of a Ni91 at. %Pt 9 at.% specimen at 1100 K the surface of a (111)-oriented specimen is enriched in platinum by a factor of two in relation to the bulk. The phenomenon of short-range ordering has been investigated on the surface and in the subsurface volume. A 3D reconstruction of this annealed NiPt specimen shows regions with high concentration of platinum that gives an indication at short-range ordering. Uniform sputtering of the tip without a heat treatment induces a decisive depletion of Pt on the surface and the following subatomic layers. The atom-probe results of specimens in thermal equilibrium are in close agreement to further surface sensitive results obtained from Ion Scattering Spectroscopy (ISS) and Auger Electron Spectroscopy (AES).     

因素空间理论与知识表示的数学框架（Ⅷ）─—变权综合原理

本文是文［１－７］的继续，研究变权综合问题，从确定变权的经验公式入手引出了变权原理，给出了变权的公理化定义，讨论了与之有关的均衡函数及其梯度向量。     

An approach combining the Ritz-Galerkin and finite difference methods

The nonconforming combination of Ritz-Galerkin and finite difference methods is presented for solving elliptic boundary value problems with singularities. The Ritz-Galerkin method is used in the subdomains including singularities, the finite difference method is used in the rest of the solution domain. Moreover, on the common boundary of two regions where two different methods are used, the continuity conditions are constrained only on the nodes of difference grids. Theoretical analysis and numerical experiments have shown that average errors of numerical solutions and their generalized derivatives can reach the convergence rate O(h^2-δ), where h is the mesh spacing of uniform difference grids, and δ is an arbitrarily small, positive number. This convergence rate is better than O(h), obtained by the nonconforming combination of the Ritz-Galerkin and finite element methods.     

Numerical solutions of the shallow water equations with discontinuous bed topography

A simple scheme is developed for treatment of vertical bed topography in shallow water flows. The effect of the vertical step on flows is modelled with the shallow water equations including local energy loss terms. The bed elevation is denoted with z_b^‐ for the left and z_b⁺ for the right values at each grid point, hence exactly representing a discontinuity in the bed topography. The surface gradient method (SGM) is generalized to reconstruct water depths at cell interfaces involving a vertical step so that the fluxes at the cell interfaces can accurately be calculated with a Riemann solver. The scheme is verified by predicting a surge crossing a step, a tidal flow over a step and dam‐break flows on wet/dry beds. The results have shown good agreements compared with analytical solutions and available experimental data. The scheme is efficient, robust, and may be used for practical flow calculations. Copyright © 2002 John Wiley & Sons, Ltd.     

Efficient computation of natural convection in a concentric annulus between an outer square cylinder and an inner circular cylinder

In this work, the natural convection in a concentric annulus between a cold outer square cylinder and a heated inner circular cylinder is simulated using the differential quadrature (DQ) method. The vorticity‐stream function formulation is used as the governing equation, and the coordinate transformation technique is introduced in the DQ computation. It is shown in this paper that the outer square boundary can be approximated by a super elliptic function. As a result, the coordinate transformation from the physical domain to the computational domain is set up by an analytical expression, and all the geometrical parameters can be computed exactly. Numerical results for Rayleigh numbers range from 104 to 106 and aspect ratios between 1.67 and 5.0 are presented, which are in a good agreement with available data in the literature. It is found that both the aspect ratio and the Rayleigh number are critical to the patterns of flow and thermal fields. The present study suggests that a critical aspect ratio may exist at high Rayleigh number to distinguish the flow and thermal patterns. Copyright © 2002 John Wiley & Sons, Ltd.     

Double-layer structural-acoustic coupling for cylindrical shell by using a combination of WDA and BIE

This work formulates the double-layer structural-acoustic coupling problem for cylindrical shell by using a combination of the wave-number domain approach (WDA) and the boundary integral equation (BIE). Expressions for the spectral radial velocity of the outer surface of a finite fluid-filled/submerged (FFS) cylindrical thin shell are formulated by means of the transfer matrix equation in wave-number domain. It is shown that the spectral variables on the inner surface of the shell are related to those on the outer surface of the shell. The far field sound radiation from this kind of shell is numerically evaluated for various fluid cases. An experimental verification is performed, and a good correlation between the theoretical results and the experimental results shows that the theoretical study work in this paper is correct.