Sequential injection spectrophotometric determination of trace amounts of iodide by its catalytic effect on the 4,4'-methylenebis(N,N-dimethylaniline)-chloramine-T reaction

A simple and sensitive sequential injection spectrophotometric procedure is proposed for the determination of trace amounts of iodide in pharmaceutical preparations. The method is based on the catalytic effect of iodide on the (tetra base) 4,4′-methylenebis(N,N-dimethylaniline)-chloramine-T reaction in acidic solution. The method involves a sequential aspiration of 255 μl sample/standard followed by 170 μl tetra base and then 128 μl chloramine-T solutions into a carrier stream to be stacked inside a holding coil and flow reversed through a reaction coil towards a detector. The resulting colored compound is measured at 600 nm using an UV/Vis-spectrophotometer. All the parameters that affect the reaction were evaluated and the calibration curve is linear over a range of 0.1–6.0 μg l⁻¹ of iodide concentration with detection limit of 0.05 μg l⁻¹. A sample throughput of 80 samples per hour and relative standard deviation of less than 2.0% was achieved. The method is successfully applied for the determination of iodide in three different samples (tablets).     

Spectrophotometric determination of magnesium in pharmaceutical preparations by cost-effective sequential injection analysis

A simple and rapid, inexpensive spectrophotometric method was proposed for magnesium assay in pharmaceutical preparations by sequential injection analysis (SIA). The method is based on the reaction between o-cresolphthalein complexone (CPC) and Mg(II) in alkaline media, yielding a pink colored complex with absorption maximum at 570 nm. Since the formation constant between Ca-CPC and Mg-CPC is similar, initially a sample/standard solution was aspirated into the holding coil followed by a mixture of masking-buffer solutions. This was done because masking of calcium should be accomplished before Mg-CPC complexation. Then the reagent was introduced into the reaction coil to produce a colored complex, which is measured spectrophotometrically at 570 nm. In this way the interference of calcium was reduced. Furthermore, all the parameters that affect the reaction were evaluated. The calibration curve is linear over a range of 0-20 mg l⁻¹ of Mg(II) with a detection limit of 0.24 mg l⁻¹. A sample throughput of 80 samples per hour and relative standard deviation <2.0% were achieved. The proposed method was successfully applied for the assay of magnesium in three different compositions of pharmaceutical preparations (tablets). The results were found to be in good agreement with the manual flame atomic absorption spectrophotometry (FAAS) and UV-Vis spectrophotometry methods and with the claimed values by the manufactures. The t-test shows no significant difference at 95% confidence level.     

Sequential injection spectrophotometric determination of iron as Fe(II) in multi-vitamin preparations using 1,10-phenanthroline as complexing agent

A sequential injection analysis (SIA) system is proposed for the determination of iron (II). Fe(II) was determined by SIA based on the reaction between 1,10-phenanthroline and iron (II), yielding an orange–red colour complex with absorption maximum at 512 nm. The method involved aspiration of 187 μl sample/standard zone followed by a zone of a reagent solution containing 140 μl of 7.8 × 10⁻⁴ mol l⁻¹ 1,10-phenanthroline into a carrier stream to be stacked inside a holding coil and flow reversed through a reaction coil to a detector. The optimum condition was evaluated and the calibration curve is linear over a range of 0.25 to 5.0 mg l⁻¹ of Fe(II) with detection limit of 18 μg l⁻¹. A sample throughput of 40 h⁻¹ was established. This technique is found to be simple, accurate, reproducible and sensitive. The proposed method was successfully applied for the determination of total iron as Fe(II) in pharmaceutical products (multi-vitamin tablets) and is especially useful for the determination of iron (II) in tablets with lower iron (II) contents. The results were found to be in good agreement with the results obtained by manual UV/Vis spectrophotometry and flame atomic absorption spectrometry (FAAS) and with claimed values by the manufacturers.     

Experimental, Theoretical and Biological Activity Study on the Acyl-Substituted Benzo-18-crown-6, Dibenzo-18-crown-6 and Dibenzo-24-crown-8

Hexadecanoyl, dihexadecanoyl, dioctadecaneoyl, di-10-undecenoyl, and dicis-9-octadecenoyl derivatives of benzo[18]crown-6, dibenzo[18]crown-6 and dibenzo[24]-8 were synthesized by the condensation of carboxylic acids (palmitic, stearic, oleic and undecenoic acid) with benzo and dibenzo crown ethers in the presence of zinc chloride. The extraction equilibrium constants of such macrocyclic ethers with long side chains were estimated using chloroform/water and dichloromethane/water membranes transfer of Na-PAR (4-(2-pyridylazo)-resorcinol mono sodium monohydrate) with UV–Vis spectroscopy. It was found that they were in the range of 10.88–11.71 in dichloromethane and 8.04–11.77 in chloroform. These results actually show that the Na+ binding effect of macrocyclic ethers depends on the type and the length of side chains. The geometrical properties of the molecules were studied employing semi-empirical calculations by simulated annealing technique. The frontier molecular orbital energies and dipole moments were also examined. The biological activity results showed that the synthesized crown ethers have no activity against the studied microorganisms.     

修饰基团的结构对 β -环糊精衍生物的分析特性的影响Ⅰ 可离解基团的影响

本文以螯合阳离子、螯合阴离子和具有阴、阳电性互变异构体的三种类型的显色体系为例 ,比较研究了未经修饰的 β -环糊精 (β-CD)与经荷阴离子、阳离子取代基修饰的 β-CD衍生物对这三种类型显色体系的增效作用的机理 ,总结出这些衍生物对显色反应作用的规律 .