Synthesis of Small‐Sized,Porous, and Low‐Toxic Magnetite Nanoparticles by Thin POSS Silica Coating

In this communication, we report the synthesis of small‐sized (<10 nm), water‐soluble, magnetic nanoparticles (MNPs) coated with polyhedral oligomeric silsesquioxanes (POSS), which contain either polyethylene glycol (PEG) or octa(tetramethylammonium) (OctaTMA) as functional groups. The POSS‐coated MNPs exhibit superparamagnetic behavior with saturation magnetic moments (51–53 emu g^?1) comparable to silica‐coated MNPs. They also provide good colloidal stability at different pH and salt concentrations, and low cytotoxicity to MCF‐7 human breast epithelial cells. The relaxivity data and magnetic resonance (MR) phantom images demonstrate the potential application of these MNPs in bioimaging.     

Evidence for internal resistive barriers in a crystal of the giant dielectric constant material: CaCu3Ti4O12

Complex impedance spectra were obtained on a crystal of CaCu₃Ti₄O₁₂ (CCTO) from 289 to 456 K. As in the case of ceramic CCTO, these spectra can be interpreted as arising from a conducting material containing insulating barriers. This is then further evidence for the existence of planar defects within crystals of CCTO that act as insulating barriers and produce the large dielectric constant through a space charge mechanism.     

Total electron scattering cross sections for carbon dioxide at low electron energies

Absolute total electron scattering cross sections for carbon dioxide have been measured at low electron energies using a photoelectron source. The measurements have been carried out at 27 electron energies varying from 0.91–9.14 eV with an accuracy of ±3%. The cross sections obtained in the present experiment have been compared with other measurements and theoretical computations.     

Characterization of surface deformation around Vickers indentations in InGaAsP epilayers on InP substrate

The deformation surrounding Vickers indentations on InGaAsP/InP epilayers have been studied in detail. The surface topography was characterized by using atomic force microscopy (AFM). The material pile-up and sink-in regions around the indentation impression was observed for the quaternary InGaAsP/InP epilayers. The sectional analysis mode of the AFM shows the depth profile at the indented region. Microindentation studies were carried out for different atomic fraction of the quaternary InGaAsP/InP compound semiconductor alloys. The microhardness values of InGaAsP/InP epilayers were found to be in the range of 5.08 and 5.73 GPa. These results show that the hardness value of the quaternary alloy drastically increases as the composition of As was increased by 0.01 atomic fraction and when the phosphorous concentration decreases from 0.4 to 0.38. The reason may be that the increase in As concentration hardens the lattice when phosphorous concentration was less and hardness decreases when phosphorous was increased.     

Critical phenomena in FINEMET alloy

The Fe_73.5Cu₁Nb₃Si_13.5B₉ FINEMET alloy has been prepared by the rapid solidification technique. The critical behaviour of this alloy in the amorphous as well as in its nanocrystalline states has been studied near their respective Curie temperatures. From the values of the critical exponents one can conclude that the alloy behaves like a 3D Heisenberg ferromagnet in the amorphous and nanocrystalline states. But there exists a slight increase in the value of β for the alloy annealed at 823 K (the nanocrystalline state) as observed in most of the amorphous alloys.     

Precise lattice parameter measurements in CsCl-Br solid solutions between room temperature and 90°K by powder x-ray diffraction

Solid solutions of CsCl-Br in five different concentrations were prepared in sealed quartz tubes by heating the mixture to 1123°K for 6–8 hr and quenching to room temperature. X-ray diffractograms were taken at eight different temperatures between room temperature and 90°K for these solid solutions using the YPC50NM powder diffractometer and a continuous flow cryostat. The observed lattice parameters for each sample at each temperature obtained from the powder diffractograms were then extrapolated to give the true lattice parameters using the least square method with Nelson-Riley extrapolation scheme. The values of the true lattice parameters at each concentration and at each temperature were tabulated and the results discussed. It is shown that the lattice parameters vs temperature for some concentrations exhibit an anomalous behaviour. Contribution No. 691     

Local control of electric current driven shell etching of multiwalled carbon nanotubes

We report on a novel method for local control of shell engineering in multiwalled carbon nanotubes (MWNTs) using Joule-heating induced electric breakdown. By modulating the heat dissipation along a nanotube, we can confine its thinning and shell breakdown to occur within localized regions of peak temperatures, which are distributed over one-half of the NT length. The modulation is achieved by using suitably designed nanomachined heat sinks with different degrees of thermal coupling at different parts of a current-carrying nanotube. The location of electric breakdown occurs precisely at the regions of high temperatures predicted by the classical finite-element model of Joule heating in the MWNT. The experiments herein provide new insight into the electric breakdown mechanism and prove unambiguously that shell removal occurs due to thermal stress, underpinning the diffusive nature of MWNTs. The method demonstrated here has the potential to be a powerful tool in realizing MWNT bearings with complex architectures for use in integrated nanoelectromechanical systems (NEMS). In addition, the breakdown current and power in the nanotubes are significantly higher than those observed in nanotubes without heat removal via additional heat sinks. This indicates future avenues for enhancing the performance of MWNTs in electrical interconnect and nanoelectronic applications. PACS  73.63.Fg; 65.80.+n