Mössbauer and infrared spectroscopic studies of novel mixed valence states in cobaltous ferrocyanides and ferricyanides

Novel mixed valence states have been obtained by the treatment of cobaltous ferrocyanides (Co⁺²Fe^II) and ferricyanides (Co⁺²Fe^III) in an ozone flow. The CN stretching bands occur at 2085 cm^–1 for Co⁺²Fe^II and at 2160 cm^–1 for Co⁺²Fe^III. After the ozonization process of Co⁺²Fe^II, an intense band approximately at 2125 cm^–1 is detected. This intermediate band must correspond to a mixed valence state of the type: Fe^II–CN–Co²⁺–NC–Fe^III Mössbauer spectra recorded in situ during the ozonization of Co⁺²Fe^II show the presence of two components: a doublet with isomer shift and quadrupole splitting values close to the cobalti ferricyanide and a very broad line for the mixed valence state. From the Mössbauer and infrared spectra of the aged samples of the Co⁺²Fe^II after ozonization, a relaxation process to the initial state of the samples is observed but the mixed valence state is stable.     

Non-linearity with metal-metal indicator complex reactions in flow-injection analysis

The linearity of the standard calibration curve in a flow-injection system involving a calcium-cresolphthalein complexone reaction was improved by replacing the organic base, 2-amino-2-methylpropan-1-ol, with the weak inorganic acid-conjugate base, boric acid-borate system as buffer. This was done after a theoretical study done on the relationship between the amount of coloured complex, Ca(2)(CPC)(2-), as major chromophore formed and the total amount of calcium added at different pH values, and employing the knowledge obtained via proton side-reactions. It was shown that a linear calibration curve between 150 and 1000 mg l(-1) of standard Ca(2-) solutions was obtained with a buffer solution containing 0.05 mol l(-1) boric acid, 0.05 mol l(-1) KCl and 35 g l(-1) sodium acetate at a pH of 8.5.     

An on-line potentiometric sequential injection titration process analyser for the determination of acetic acid

An on-line potentiometric sequential injection titration process analyser for the determination of acetic acid is proposed. A solution of 0.1 mol L(-1) sodium chloride is used as carrier. Titration is achieved by aspirating acetic acid samples between two strong base-zone volumes into a holding coil and by channelling the stack of well-defined zones with flow reversal through a reaction coil to a potentiometric sensor where the peak widths were measured. A linear relationship between peak width and logarithm of the acid concentration was obtained in the range 1-9 g/100 mL. Vinegar samples were analysed without any sample pre-treatment. The method has a relative standard deviation of 0.4% with a sample frequency of 28 samples per hour. The results revealed good agreement between the proposed sequential injection and an automated batch titration method.     

Diamond paste-based electrodes for determination of Cr(III) in pharmaceutical compounds

A new class of monocrystalline diamond paste-based electrodes is proposed for the determination of chromium(III) at trace levels in vitamins. Three types of monocrystalline diamond—natural diamond 1 (natural diamond), synthetic diamond 50 (synthetic-1), and synthetic diamond 1 (synthetic-2)—were used for electrode construction. The linear concentration ranges are between 10^–10 and 10^–8; 10^–9 and 10^–7, and 10^–10 to 10^–8 mol L^–1, with limits of detection of 10^–12, 10^–12, and 10^–11 mol L^–1, when natural diamond, synthetic-1, and synthetic-2, respectively, are used as electrode materials. For electrodes based on natural diamond and synthetic-1 it was found that Cr(III) yields a peak at about +0.275±0.015 V (vs. Ag/AgCl) within a predetermined positive potential range situated between +0.4 and +0.2 V, while for the electrode based on synthetic-2 the peaks are found at +0.300±0.015 V (vs. Ag/AgCl). The proposed method is reliable for the determination of chromium(III) at trace levels in two vitamin tablets (RSD<0.2%).     

Utilization of maltodextrin based enantioselective, potentiometric membrane electrodes for the enantioselective assay of S-perindopril

Enantioselective, potentiometric membrane electrodes (EPMEs) based on carbon paste impregnated with different maltodextrins {dextrose equivalent (DE) 4.0-7.0 (I), 13.0-17.0 (II) and 16.5-19.5 (III)} as chiral selectors for the assay of S-perindopril is described. The proposed electrodes could be reliably employed in the assay of S-perindopril raw material and from its pharmaceutical formulation, Coversyl^® tablets. The electrode based on maltodextrin (I) showed the best enantioselectivity and time-stability. The surfaces of the electrodes are easily renewable by simply polishing on an alumina paper.     

Practical and quality-control aspects of multi-element analysis with quadrupole ICP–MS with special attention to urine and whole blood

Two screening methods were developed for rapid analysis of a great number of urine and blood samples within the framework of an exposure check of the population after a firework explosion. A total of 56 elements was measured including major elements. Sample preparation consisted of simple dilution. Extensive quality controls were applied including element addition and the use of certified reference materials. Relevant results at levels similar to those found in the literature were obtained for Co, Ni, Cu, Zn, Sr, Cd, Sn, Sb, Ba, Tl, and Pb in urine and for the same elements except Ni, Sn, Sb, and Ba in blood. However, quadrupole ICP–MS has limitations, mainly related to spectral interferences, for the analysis of urine and blood, and these cause higher detection limits. The general aspects discussed in the paper give it wider applicability than just for analysis of blood and urine—it can for example be used in environmental analysis.