Fabrication of a freestanding GaN layer by direct growth on a ZnO template using hydride vapor phase epitaxy

A new hydride vapor phase epitaxy (HVPE)-based approach for the fabrication of freestanding GaN (FS-GaN) substrates was investigated. For the direct formation of low-temperature GaN (LT-GaN) layers, the growth parameters were optimized: the polarity of ZnO, the growth temperature, and the V/III ratio. The FS-GaN layer was achieved by gas etching in an HVPE reactor. A fingerprint of Zn out-diffusion was detected in the photoluminescence measurements, especially for the thin (80 μm) FS-GaN film; however, a thicker film (400 μm) was effectively reduced by optimization of GaN growth.     

Atomic-scale visualization of antisite defects in LiFePO4

We visualize the antisite exchange defects in LiFePO4 crystals with an ordered olivine structure by using annular dark-field scanning transmission electron microscopy (STEM). A recognizable bright contrast is observed in some of the Li columns of STEM images in a sample annealed at a lower temperature, which directly demonstrates the disordered occupations by Fe atoms. Furthermore, such exchange defects appear to be locally aggregated rather than homogeneously dispersed in the lattice, although their overall concentration is fairly low. The present study emphasizes the significance of atomic-level observations for the defect distribution that cannot be predicted by macroscopic analytical methods.     

Bulk synthesis of ordered macroporous silica particles for superhydrophobic coatings

The molecular interaction between tetrabutylammonium iodide (TBAI) and cellulose and its potential application for the adsorption of chromium is discussed in this paper. The biosorbent was prepared under solvent free conditions using microwave irradiation. A subtle balance between electrostatic and the hydrophobic effects governs the interaction of biopolymer with the surfactant. The interaction between the biosorbent and chromium was comprehensively studied using spectroscopic, thermal and surface analysis techniques. The various analytical parameters that influence the adsorption were optimized, and the maximum adsorption capacity of Cr(VI) obtained from the Langmuir isotherm model was found to be 16.67 mg g(-1). The sorption thermodynamics indicated the spontaneity and exothermic nature of adsorption. The biosorbent could be effectively regenerated using NaOH, which imparts greener aspect to the overall process.     

Practical neutral aromatic nitration with nitrogen dioxide in the presence of heterogeneous catalysts under moderate oxygen pressure

A practical neutral aromatic nitration process using nitrogen dioxide in the presence of FeCl₃ · 6H₂O under 40–100 psig of oxygen was developed, and nitration of several aromatic compounds, including the deactivated nitrobenzene, was performed in a successful manner. The correlation of reaction rate with equivalents nitrogen dioxide, oxygen pressure, amount of catalyst and temperature was investigated through the nitration of benzene. Following the optimization of reaction conditions, the nitration of benzene was scaled up to 476 mol. Furthermore, inorganic solid catalysts with pore size over 5 Å and surface area over 100 m²/g were applied to newly developed neutral nitration.     

Effect of hydrogen reduction temperature on the microstructure and magnetic properties of Fe–Ni powders

The effect of hydrogen reduction temperature on the properties of Fe–Ni powders was described. The mixed powders of Fe-oxide and NiO were prepared by chemical solution mixing of nitrates powders and calcination at 350 °C for 2 h in air. The calcined powders formed small agglomeration with an average particle size of 100 nm. The microstructure and magnetic properties were investigated by using X-ray diffractometry, thermogravimetry, differential thermal analyzer, and vibrating sample magnetometer. Microstructure and thermal analysis revealed that the Fe-oxide and NiO phase were changed to FeNi₃ phase in the temperature range of 245–310 °C, and by heat-up to 690 °C the FeNi₃ phase was transformed to γ-FeNi phase. The reduced powder at 350 °C showed saturation magnetization of 76.3 emu/g and coercivity of 205.5 Oe, while the reduced powders at 690 °C exhibited saturation magnetization of 84.0 emu/g and coercivity of 14.0 Oe. The change of magnetic properties was discussed by the observed microstructural features.

     

The stability of graphene and boron nitride for III-nitride epitaxy and post-growth exfoliation

A challenging approach, but one providing a key solution to material growth, remote epitaxy (RE)—a novel concept related to van der Waals epitaxy (vdWE)—requires the stability of a two-dimensional (2-D) material. However, when graphene, a representative 2-D material, is present on substrates that have a nitrogen atom, graphene loss occurs. Although this phenomenon has remained a hurdle for over a decade, restricting the advantages of applying graphene in the growth of III-nitride materials, few previous studies have been conducted. Here, we report the stability of graphene on substrates containing oxygen or nitrogen atoms. Graphene has been observed on highly decomposed Al₂O₃; however, graphene loss occurred on decomposed AlN at temperatures over 1300 °C. To overcome graphene loss, we investigated 2-D hexagonal boron nitride (h-BN) as an alternative. Unlike graphene on AlN, it was confirmed that h-BN on AlN was intact after the same high-temperature process. Moreover, the overgrown AlN layers on both h-BN/AlN and h-BN/Al₂O₃ could be successfully exfoliated, which indicates that 2-D h-BN survived after AlN growth and underlines its availability for the vdWE/RE of III-nitrides with further mechanical transfer. By enhancing the stability of the 2-D material on the substrate, our study provides insights into the realization of a novel epitaxy concept.

A challenging approach, but one providing a key solution to material growth, remote epitaxy (RE)—a novel concept related to van der Waals epitaxy (vdWE)—requires the stability of a two-dimensional (2-D) material.     

Harmonious Heterointerfaces Formed on 2D-Pt Nanodendrites by Facet-Respective Stepwise Metal Deposition for Enhanced Hydrogen Evolution Reaction

The performance of nanocrystal (NC) catalysts could be maximized by introducing rationally designed heterointerfaces formed by the facet- and spatio-specific modification with other materials of desired size and thickness. However, such heterointerfaces are limited in scope and synthetically challenging. Herein, we applied a wet chemistry method to tunably deposit Pd and Ni on the available surfaces of porous 2D−Pt nanodendrites (NDs). Using 2D silica nanoreactors to house the 2D-PtND, an 0.5-nm-thick epitaxial Pd or Ni layer ( e - Pd or e -Ni ) was exclusively formed on the flat {110} surface of 2D−Pt, while a non-epitaxial Pd or Ni layer ( n - Pd or n -Ni ) was typically deposited at the {111/100} edge in absence of nanoreactor. Notably, these differently located Pd/Pt and Ni/Pt heterointerfaces experienced distinct electronic effect to influence unequally in electrocatalytic synergy for hydrogen evolution reaction (HER). For instance, an enhanced H₂ generation on the Pt{110} facet with 2D-2D interfaced e -Pd deposition and faster water dissociation on the edge-located n -Ni overpowered their facet-located counterparts in respective HER catalysis. Therefore, a feasible assembling of the valuable heterointerfaces in the optimal 2D n -Ni/e-Pd/Pt catalyst overcame the sluggish alkaline HER kinetics, with a catalytic activity 7.9 times higher than that of commercial Pt/C.