Matrix-assisted laser desorption/ionization mass spectrometry of collected bioaerosol particles

A method was developed for collection and analysis of bioaerosols by matrix-assisted laser desorption/ionization (MALDI) time-of-flight mass spectrometry using a modified Andersen N6 bioaerosol collector. The overall goal of the study was to develop methods for obtaining mass spectra with minimal reagents and treatment steps for potential use in remote collection and analysis systems. Test bioaerosol particles were generated from a nebulized E. coli bacterial suspension and collected on MALDI targets placed in an Andersen N6 single-stage aerosol impactor. The bioaerosols were mixed with matrix either by deposition on a bare target with the matrix solution added later, or by deposition on a target pre-coated with matrix. The matrix compounds alpha-cyano-4-hydroxycinnamic acid (CHCA) and sinapic acid (SA) were tested and the SA matrix was found to give the best results in number of peaks, resolution, and signal-to-noise ratio. Deposition of bioaerosol particles onto the matrix pre-coated target did not produce signal in the m/z region above 1000, but the signal could be recovered with the addition of a 1:1 (v/v) acetonitrile/water solvent. Addition of solvent by pipette to the pre-coated targets after particle deposition recovered signal comparable to the dried-droplet sample preparations, whereas solvent sprayed into the impactor recovered fewer peaks. Deposition on pre-coated targets with post-collection solvent addition was superior to deposition on bare target followed by post-collection addition of matrix solution.     

Anodic stripping voltammetry of sulphide at a nickel film: towards the development of a reagentless sensor

The determination of sulphide at an electrochemically generated nickel oxide layer at glassy carbon and screen-printed electrodes in acidic media has been examined and appraised. The NiO layer was found to produce a stripping-like signal to sulphide and gave a linear peak current response from 20 to 90 μM. The response was further enhanced by repetitive cycling allowing accumulation of nickel sulphide at the electrode surface such that lower micromolar levels of sulphide (i.e. 5 μM) can be determined. The response at the NiO layer to sulphide is shown to be reproducible over a period of 24 h, thereby offering the development of a disposable amperometric sensor for sulphide.     

Channel flow cell studies on the evaluation of surface pretreatments using phosphoric acid or polymaleic acid for calcite stone protection

The dissolution kinetics of surface-pretreated and weathered calcite was investigated in dilute acid using a channel flow cell with microdisk detection. Two pretreatments were studied, polymaleic acid and phosphoric acid. Treatment with polymaleic acid was shown to significantly passivate calcite but to a lesser extent than the phosphoric acid and the former coating was found to be less effective for protection of calcite from acid attack. However, treatment of calcite with phosphoric acid resulted in the passivation of calcite from acid attack which strongly inhibited dissolution, an effect that was enhanced even further after exposure to the environment.     

Generic serial and parallel on-line direct-injection using turbulent flow liquid chromatography/tandem mass spectrometry

The development of turbulent flow chromatography (TFC) has enabled considerable growth in the utility of on-line direct-injection technologies. TFC has now become established in a large number of varied analytical environments, particularly drug discovery/pharmacokinetics, metabolite profiling, combinatorial library purification, pre-clinical and clinical GLP applications. The utility of turbulent flow technology for in-house pre-clinical and clinical quantitative applications has necessitated extensive valve-cleaning procedures, and consequently lengthy cycle-times, to effectively remove the system carry-over. In-house requirements for assay validation require carry-over less than 20% of the lowest level of quantification (LLOQ), corresponding to 0.02% carry-over for a linear calibration range incorporating 3 orders. A generic turbulent flow chromatography protocol has been developed for drug discovery that incorporates polymeric turbulent flow extraction (cyclone) with C18-based reverse-phase chromatography. Further, multiple wash steps are incorporated within the methodology to meet in-house requirements for carry-over. Selection of novel switching-valve materials based on polyarylethyl ketone (PAEK) and Hastelloy/Valcon E autosampler injection hardware has enabled us to significantly impact the cycle-time required to reduce carry-over. Consequently, optimal usage of switching valves has enabled parallel operation for a generic on-line direct-injection methodology to successfully reduce the total cycle-time. Overall reductions from 4 min per sample to 90 s per sample are shown with comparable data quality using a proprietary target molecule from 0.1-100 ng/mL. This paper describes the hardware configuration and methodologies utilized to perform generic serial and parallel on-line direct-injection using a Turboflow HTLC 2300 system.     

Channel Flow Cell Studies of the Inhibiting Action of Gypsum on the Dissolution Kinetics of Calcite: A Laboratory Approach with Implications for Field Monitoring

The rate of dissolution of surface-treated calcite crystals in aqueous acidic solution has been studied using an adaptation of the channel flow cell method with microdisc electrode detection. Surface treatments of calcite with sulfuric acid lead to the nucleation of gypsum overgrowths, which reduce the rate of dissolution of calcite. Rate constants for untreated calcite and calcite pretreated with sulfuric acid conditions of 0.01 M for 1 h, 0.05 M for 5 h, and 0.1 M for 21 h are found to be 0.035, 0.018, 0.006, and 0.004 cm s(-1), respectively. Deterioration of calcite materials caused by acid deposition was investigated by field exposure of untreated and sulfate pretreated calcite rocks under urban conditions for 12 months. The rate constant for both pretreated and untreated calcite exposed to weathering is 0.003 cm s(-1). This suggests that calcite self-passivates the surface from further reaction when exposed to acid deposition. However, surface studies indicate that the surface undergoes erosion and dissolution before passivation. Pretreatment of the surface with sulfate protects the surface from acid deposition so it remains less reactive toward acid compared with untreated calcite. Copyright 2001 Academic Press.     

On-line laser desorption/ionization mass spectrometry of matrix-coated aerosols

Matrix-assisted laser desorption/ionization (MALDI) was used for the on-line analysis of single particles. An aerosol was generated at atmospheric pressure and particles were introduced into a time-of-flight (TOF) mass spectrometer through a single-stage differentially pumped capillary inlet. Prior to entering the mass spectrometer, a matrix was added to the particles using a heated saturator and condenser. A liquid matrix, 3-nitrobenzyl alcohol (NBA), and a solid matrix, picolinic acid (PA), were used. Particles were ablated with a 351 nm excimer laser and the resulting ions were mass-separated in a two-stage reflectron TOF mass spectrometer. Aerosol particles containing the biomolecules erythromycin and gramicidin S were analyzed with and without the matrix addition step. The addition of NBA to the particles resulted in mass spectra that contained an intact molecular ion mass peak. In contrast, PA-coated particles did not yield molecular ion peaks from matrix-coated particles.     

Dewetting of liquids on ceramic surfaces at high temperatures.

The influence of surface structure and chemistry on high-temperature dewetting of silicate liquids on ceramic surfaces has been investigated. Model systems based on well-defined crystallography and known chemistry have been used to illustrate the effect of surface roughness and chemistry on the dewetting process. Reconstructed ceramic surfaces provide ideal substrates to study effects of surface roughness. It has been shown that the morphology of dewet droplets depend on the length scale and the crystallography of the facets on the surface. Complex pattern formation due to solute redistribution during dewetting is illustrated in the case of SiO2 dewetting on (001) rutile substrates. The role of kinetics on the dewetting process has also been clarified.