The use of emulsions for the determination of methylmercury and inorganic mercury in fish-eggs oil by cold vapor generation in a flow injection system with atomic absorption spectrometric detection

An on-line time based injection system used in conjunction with cold vapor generation atomic absorption spectrometry and microwave-aided oxidation with potassium persulfate has been developed for the determination of the different mercury species in fish-eggs oil samples. A three-phase surfactant-oil-water emulsion produced an advantageous flow when a peristaltic pump was used to introduce the highly viscous sample into the system. The optimum proportion of the oil-water mixture ratio was 2:3 v/v with a Tween 20 surfactant concentration in the emulsion of 0.008% v/v. Inorganic mercury was determined after reduction with sodium borohydride while total mercury was determined after an oxidation step with persulfate prior to the reduction step to elemental mercury with the same reducing agent. The difference between total and inorganic mercury determined the organomercury content in samples. A linear calibration graph was obtained in the range 0.1-20 micrograms l-1 of Hg2+ by injecting 0.7 ml of samples. The detection limits based on 3 sigma of the blank signals were 0.11 and 0.12 microgram l-1 for total and inorganic mercury, respectively. The relative standard deviation of ten independent measurements were 2.8 and 2.2% for 10 micrograms l-1 and 8.8 and 9.0% for 0.1 microgram l-1 amounts of total and inorganic mercury, respectively. The recoveries of 0.3, 0.6 and 8 micrograms l-1 of inorganic and organic mercury added to fish-eggs oil samples ranged from 93.0 to 94.8% and from 100 to 106%, respectively. Good agreement with those values obtained for total mercury content in real samples by electrothermal atomic absorption spectrometry was also obtained, differences between mean values were < 7%. With the proposed procedure, 22 proteropterous catfish-eggs oil samples from the northwestern coast of Venezuela were measured; while the organic mercury lay in the range 2.0 and 3.3 micrograms l-1, inorganic mercury was not detected.     

Determination of paraquat in human blood plasma using reversed-phase ion-pair high-performance liquid chromatography with direct sample injection

This report describes the determination of paraquat (PQ) in human blood plasma samples by a direct-injection reversed-phase ion-pair chromatographic method. Blood plasma filtrate was injected directly into the LiChrospher® RP-18 alkyl-diol silica (ADS) precolumn integrated in a column switching system using a mixture of 3% 2-propanol and 10 mM sodium octane sulfonate (SOS) in a 0.05 M phosphate buffer (pH 2.8). After washing with this phase, the ADS precolumn was back-flushed with the analytical mobile phase consisting of 40% of methanol and 10 mM SOS in a 0.05 M phosphate buffer (pH 2.8) at a flow rate of 1.0 ml min⁻¹, in order to carry the analyte to a conventional reversed-phase analytical column, where the separation of PQ was achieved and finally detected by UV at 258 nm. The recoveries of PQ from human blood plasma samples ranged between 95.0 and 99.5% at nine different concentrations (from 0.05 to 3.00 μg of PQ ml⁻¹) with coefficients of variation <2.5% (n=3). The precision expressed as relative standard deviation was below 3.5% for between-day and below 4.3% for within-day measurements (n=5). The detection limit (signal-to-noise ratio, S/N>3) was 0.005 μg ml⁻¹ with an injection volume of 200 μl. The proposed method is promising for the identification and quantification of PQ at low concentration levels and is suitable for its analysis in human blood plasma samples from intentional or accidental poisonings cases with a sample throughput of 5 samples per hour.     

Determination of lead in the urine of exposed and unexposed adults by extraction and flow-injection/atomic absorption spectrometry

Lead is extracted from urine with ammonium pyrrolidien dithiocrbamate into methyl isobutyl ketone, and 20 μl of the extract is injected into a water carrier stream in a flow-injection/atomic absorption system. The procedure is simple, quick, accurate and reproducible. Recoveries are 96–105%. The mean urine lead contents of 20 unexposed and 20 printing-press lead exposed workers was found to be 39.0 ± 8.3 and 71.7 ± 26.3 μg Pb l^?1, respectively.     

A new multi analytical approach for the identification of synthetic and natural dyes mixtures. The case of orcein-mauveine mixture in a historical dress of a Sicilian noblewoman of nineteenth century

Abstract

In this paper, the application of a multi-analytical approach for the characterisation of synthetic and natural dyes in a historical textile is presented. The work is focused on a historical dress of a Sicilian noblewoman, dating from about 1865–1870. Firstly, SERS on fibre was performed, in order to individuate the classes of dyes employed. The SERS spectra suggested the presence of two main dyes: mauveine and orcein. In order to confirm these preliminary results, two different extraction protocols were applied. The extracts obtained were analysed by ESI-MS, MALDI-ToF and UHPCL-MS analyses, confirming the SERS results. In particular, the application of the ammonia mild extraction technique allowed to selectively extract the phenoxazonic dyes, separating them already in the extraction step from the synthetic ones. Thanks to this multi-analytical approach, this dress could be considered as one of the first examples of employment of synthetic dyes in association with natural ones.     

A flow injection-ETAAS system for the on-line determination of total and dissolved silica in waters

In this work total (Si-tot) and ‘soluble’ or reactive (Si-sol) concentrations of silicon in natural and tap waters were sequentially determined by electrothermal atomic absorption spectrometry (ETAAS). First, samples were on-line diluted based on the merging-zone principle in order to allow the determination of Si-tot within the 300–1000 μgSi l⁻¹ range. After the dilution process, a sub-sample was collected in the capillary of a sampling arm assembly (SAA). Thereafter, samples were subject to a precipitation/dissolution process in order to allow the determination of Si-sol within the 280–850 μgSi l⁻¹. Si-sol was precipitated with ammonium chloride and collected on the walls of a knotted coil. The precipitate was dissolved with ammonium molybdate in an acidic medium (HNO₃) and a sub-sample was then collected in the SAA. In both cases, 10 μl volumes of the sub-sample were injected into the atomizer with the previous introduction of 20 ng of Eu as chemical modifier (10 μl) by the spectrometer autosampler. The recovery values obtained with natural waters spiked samples were over 46% and the agreement between observed and certified samples values was good. The proportion of Si-sol in comparison with the Si-tot was high (85–95%) in most natural waters. The precision of the method was 2.4–3.5 and 4.5–6.2% (n=10) for the determination of Si-tot and Si-sol, respectively.     

Column-switching high-performance liquid chromatographic analysis of carbamazepine and its principal metabolite in human plasma with direct sample injection using an alkyl-diol silica (ADS) precolumn

In this paper, the on-line coupling of solid-phase extraction, based on a restricted-access support with high-performance reverse phase chromatography for the analysis of carbamazepine (CBZ) and carbamazepine-10,11-epoxide (CBZ-E) in human plasma samples is described. A precolumn packed with 25 mum C(18) alkyl-diol support is used for direct plasma injection. Using column-switching techniques, the analytes were enriched on the precolumn by a 5 mM phosphate buffer (pH 7) with 2% of methanol solution at a flow-rate of 0.8 ml min(-1), while proteins and endogenous hydrophilic substances in plasma were washed off to waste. The enriched analytes were then back-flushed onto the analytical C(18) column, separated by a mixture of 10 mM phosphate buffer (pH 7) acetonitrile (70:30 v/v) solution at a flow-rate of 1.0 ml min(-1) and detected by the ultraviolet absorbance set at 212 and 285 nm and without transfer loss. Linear calibration graphs were obtained for sample injection volumes of 50 (0.2-4.0 of mug of CBZ ml(-1) and 0.1-5.0 mug of CBZ-E ml(-1), respectively), and 20 mul (5.0-20.0 mug of CBZ ml(-1)); in either case the r-value was >0.9963. Recoveries from spiked plasma samples were quantitative for both analytes and the coefficients of variation were below 3.83%. The lowest samples concentrations that can be quantified with acceptable accuracy and precision was 0.2 mug CBZ ml(-1) and 0.1 mug CBZ-E ml(-1) when a sample volume of 50 mul was injected. Concentrations of 0.08 and 0.05 mug ml(-1) of CBZ and CBZ-E were considered the limit of detection for a signal-to-noise ratio of 3. Furthermore, the developed column-switching method was successfully applied to the determination of CBZ and CBZ-E in plasma samples of patients submitted to CBZ therapy.     

A novel bioassay for screening and quantification of taxanes

We report a novel method for screening and quantifying tubulin-binding antimitotic agents that promote microtubule formation. The method is based on the shift in the peak of the fluorescence emission difference spectrum of tubulin complexed to metal free tetrakis(4-carboxyphenyl)porphyrin (TCPP) in the presence of antimitotic agents. Taxol (paclitaxel), an anti-tumor drug approved for the treatment of a variety of cancers, caused the appearance of a new fluorescence peak at 645 nm at concentrations as low as 125 nM, the intensity of which was a function of the paclitaxel concentration. Cephalomannine caused the induction of a new fluorescence peak at 651 nm only above 1 muM. Baccatin did not induce the appearance of any new peak within detectable operating measurement conditions. These observations are in accordance with the biological activities/cytotoxicities of these compounds. Accordingly, it is proposed that the new method can be used for high throughput screening of antimitotic compounds.     

Determination of manganese(II) by a chemiluminescence reaction

Manganese(II) ( 1.5 ng/ml) is determined by measuring either of the two emission peaks given by alkaline oxidation of luminol. Several other metal ions, which enhance both emission peaks, are masked by cyanide ions.     

Flow analysis-hydride generation-Fourier transform infrared spectrometric determination of antimony in pharmaceuticals

In this work, a flow analysis system with hydride generation and Fourier transform infrared (FTIR) spectrometric detection has been developed for the determination of antimony in pharmaceuticals. The method is based on the on-line mineralization/oxidation of the organic antimonials present in the sample and pre-reduction of Sb(V) to Sb(III) with K₂S₂O₈ and KI, respectively; prior to the stibine generation. The gaseous SbH₃ is separated from the solution in a gas phase separator, and transported by means of a nitrogen carrier into a short pathway (10 cm) IR gas cell, where the corresponding FTIR spectrum is acquired by accumulating 3 scans in a continuous mode. The 1893 cm⁻¹ band was used for the quantification of the antimony. The procedure is carried out in a closed system, which reduces sample handling and makes possible the complete automation of the antimony determination. The figures of merit of the proposed method (linear range: 0-600 mg l⁻¹, limit of detection (3σ)=0.9 mg l⁻¹, limit of quantification (10σ)=3 mg Sb l⁻¹, precision (R.S.D.) less than 1% and sample frequency=28 h⁻¹), are appropriate for the designed application. Furthermore, precise and accurate results were found for the analysis of different antimonial pharmaceutical samples, indicating that the methodology developed represents a valid alternative for the determination of antimony in pharmaceuticals, which could be suitable for the routine control analysis.     

Flow analysis-vapor phase generation-Fourier transform infrared (FA-VPG-FTIR) spectrometric determination of nitrite

In this work, the coupling between flow analysis (FA)–vapor phase generation (VPG) and Fourier transform infrared spectrometry (FTIR) has been proposed as a novel and alternative strategy for the determination of nitrite. The analyte was transformed into the gaseous nitric oxide (NO) by on-line reaction with potassium iodide (KI) or ascorbic acid in acidic medium. The gaseous NO generated was transported by means of a N₂ gas carrier stream inside the IR gas cell and the corresponding FTIR spectrum was acquired in a continuous mode. The absorbance at 1876 cm⁻¹, corrected by a baseline established between 1879 and 1872 cm⁻¹ at a nominal resolution of 2 cm⁻¹, was selected as a measurement criterion. The effect of different spectroscopic and flow analysis experimental parameters, such as nominal resolution, number of scans, reducing agent and its concentration, acidic medium, reagents and sample flow rates, and the carrier gas flow rate on the analytical signal, and then in the figures of merit were initially evaluated by using a standard short path length (10 cm) IR gas cell. The optimization of the system was carried out by the univariate method. The main aims of this study were: (i) to investigate the on-line generation of gaseous nitric oxide in a continuous flow system, and (ii) the use of Fourier transform infrared spectrometry as an alternative and selective detector for the determination of nitrite. The proposed method was initially tested and applied for the determination of nitrite in samples with very high concentration of nitrite, such as frankfurters.