基于MATLAB的异步电动机线性化控制系统的仿真

从异步电动机在同步旋转坐标系下的状态方程出发，在一定的条件下，对其系数矩阵简化．推出异步电动机的线性化控制模型．并基于该模型得出异步电动机的线性化控制系统．以给定电机为例，对该模型的有效性、响应用MATLAB进行仿真分析．验证的结果说明上述模型具有实用价值．     

RO-heparin Inhibits L-Selectin-mediated Neutrophils Adhesion to Vascular Endothelium Under Flow Conditions

Introduction Migrationandrecruitmentofleukocytesfromblood toinflammatorylesionsitesaresequentiallyregulated byadhesionmoleculesandtheirreceptors[1].These lectinfamilyplaysamajorroleininitiatingattachement ofneutrophilstotheactivatedendothelium.P selectin,…     

化学键合吸附剂的合成及吸附行为

在无定型硅胶上化学键合十八烷基三氯硅烷，键合率17%-20％，粒度5μm-10μm，以此键合的吸附剂可有效地吸附香烟烟气中的焦油、亚硝胺，吸附率分别为15%-18％和37%-43％，研究了化学键合吸附剂的粒度和加入量对吸附性能的影响。     

Elucidation of the pore structure of SBA-2 using Monte Carlo simulation to interpret experimental data for the adsorption of light hydrocarbons

We have measured the adsorption of methane and ethane to high pressure on SBA-2, a structured mesoporous silica composed of spheres connected by narrow channels. The experimental data were analyzed by carrying out Monte Carlo simulations of adsorption in pore structure models of different complexity and then adjusting the parameters of the models to match the Monte Carlo results to the experimental data. We found that a model based on single-sized spherical cavities was inadequate and that it is necessary to explicitly account for the interconnecting channels. Further, we found that despite the basic regularity of the SBA-2 structure, it is necessary to allow for a distribution of the sizes of both the cavities and the channels. These size distributions were obtained by fitting the parameters of the model to the experimental adsorption data, revealing detailed structural information not previously known for this material. The channels were found to be 5-15 A in diameter, while the cavities were 40-50 A in diameter. There is some evidence that the distribution of channel sizes leads to a percolation effect whereby the pore structure is not equally accessible to all adsorptives.     

Adsorption equilibrium of binary methane/ethane mixtures in BPL activated carbon: isotherms and calorimetric heats of adsorption

The adsorption of pure methane and ethane in BPL activated carbon has been measured at temperatures between 264 and 373 K and at pressures up to 3.3 MPa with a bench-scale high-pressure open-flow apparatus. The same apparatus was used to measure the adsorption of binary methane/ethane mixtures in BPL at 301.4 K and at pressures up to 2.6 MPa. Thermodynamic consistency tests demonstrate that the data are thermodynamically consistent. In contrast to two sets of data previously published, we found that the adsorption of binary methane/ethane in BPL behaves ideally (in the sense of obeying ideal adsorbed solution theory, IAST) throughout the pressure and gas-phase composition range studied. A Tian-Calvet type microcalorimeter was used to measure low-pressure isotherms, the isosteric heats of adsorption of pure methane and ethane in BPL activated carbon, and the individual heats of adsorption in binary mixtures, at 297 K and at pressures up to 100 kPa. The mixture heats of adsorption were consistent with IAST.     

Multivariate analysis of non-homogeneous peaks in liquid chromatography

Summary The effects of concentration, separation and spectral similarity as factors influencing the accuracy of iterative target testing factor analysis (ITT-FA) are investigated for three component systems by the application of analysis of variance (ANOVAR). ANOVAR is applied over a range of peak separations to map the changing effects of the three factors with increasing overlap. Two error responses were measured and analysed, (a) Relative cluster error (RCE) a measure of the error over all peaks in a cluster and (b) Relative peak error (RPE) the error of an individual peak. Multicomponent analysis (MCA) a method requiringa priori spectral information, is used as a referee method for ITT-FA.     

笃斯茎中六种无机元素含量分析

应用原子吸收光谱法测定了内蒙古地产的笃斯茎、叶中的Cu,Fe,Zn,Mn,Ca,Mg等六种人体必需微量元素及宏量元素的含量。从而为评价笃斯的品质及其药理、药效提供了具有一定价值的数据。     

Quantitative Determination of Octamethylcyclotetrasiloxane (D4) in Extracts of Biological Matrices by Gas Chromatography-Mass Spectrometry

Abstract

A method was developed and validated to measure octamethylcyclotetrasiloxane (D₄)^? quantitatively by gas chromatography-mass spectrometry (GC-MS) at low level in extracts of several biological matrices that include plasma, liver, lung, feces and fat from rats. The key to the successful determination lay in the use of extracts dried with anhydrous magnesium sulfate. This was necessary in view of the propensity of the methyl siloxane based GC-stationary phase to generate D₄ by its reaction with water present in the extracts. To enable quantiiation of D₄ at parts per billion (μg/L) levels, the base ion m/z 281 resulting from the loss of a methyl group from the parent molecule was selected for monitoring by SIM mode in GC-MS. The recovery of D₄ from any of the biological matrices was determined to be greater than 90% in three extractions. The D₄ response for the standards in GC-MS was linear (R² > 0.9900) and reproducible at concentrations ranging from 1—16,000 ng D₄/g solvent. Precision was less than 5%.