Proposing a novel combined cycle for optimal exergy recovery of liquefied natural gas

The effective utilization of the cryogenic exergy associated with liquefied natural gas (LNG) vaporization is important. In this paper, a novel combined power cycle is proposed which utilizes LNG in different ways to enhance the power generation of a power plant. In addition to the direct expansion in the appropriate expander, LNG is used as a low-temperature heat sink for a middle-pressure gas cycle which uses nitrogen as working fluid. Also, LNG is used to cool the inlet air of an open Brayton gas turbine cycle. These measures are accomplished to improve the exergy recovery of LNG. In order to analyze the performance of the system, the influence of several key parameters such as pressure ratio of LNG turbine, ratio of the mass flow rate of LNG to the mass flow rate of air, pressure ratio of different compressors, LNG pressure and inlet pressure of nitrogen compressor, on the thermal efficiency and exergy efficiency of the offered cycle is investigated. Finally, the proposed combined cycle is optimized on the basis of first and second laws of thermodynamics.     

Constructal multi-scale structure of PCM-based heat sinks

This paper inquires the effectiveness of a PCM-based heat sink as a reliable solution to portable electronic devices. This sink is composed of a PCM with low thermal conductivity and fins to boost its conductivity. The optimization is subjected to fixed heat sink volume filled with PCM between vertical equidistant fins. New fins are installed in the unheated space existing in each enclosure which is not involved in thermal distribution from vertical fins to the PCM. Based on the same principle, new fins generations are augmented stepwise to the multi-scale structure. The steps of adding fins will continue up to the point that the objective function reaches its maximal value, i.e., maximizing the longest safe operation time without allowing the electronics to reach the critical temperature. The results indicate that in each length of the enclosure, the optimum volume fraction and the best fins distance values exist in which the heat sink performance becomes maximum, and adding more fins lowers the performance of the heat sink. Increasing the enclosure’s length by \(2^{n}\) does not change them. For an enclosure with constant length, the optimal number of steps for adding fins within the enclosure is a function of the fin thickness. The results indicate that increasing the thickness changes the optimal number of adding fins inside the enclosure (normally a decrease). As the fin thickness is lowered, there will be a higher effect by adding vertical fins in the enclosure. Numerical simulations cover the Rayleigh number range \(2\times 10^{5}\le \hbox {Ra}_{\mathrm{H}} \le 2.7\times 10^{8}\), where H is the heat sink height.     

Preconcentration and Determination of Trace Nickel Using 1-(2-Pyridylazo)-2-Naphtol (PAN) Immobilized on Surfactant-Coated Alumina

A microcolumn of alumina modified with sodium dodecyl sulfate (SDS) and 1-(2-pyridylazo)-2-naphthol (PAN) was prepared for the preconcentration of trace nickel from water samples for a flame atomic absorption spectrometry (FAAS) determination. Under optimized conditions (pH = 4.0; flow rate, 5 mL min^–1) nickel (II) was retained on the column. The nickel collected on the column was eluted with 5 mL of 0.5 M nitric acid. Recovery was greater than 96.7%. A concentration factor of 300 can be achieved by passing 1500 mL of sample through the microcolumn. The relative standard deviation (ten replicate analyses) at the 40 ng mL^–1 level for nickel was 2.4%, and the corresponding limit of detection (based on 3) was 0.06 ng mL^–1. The method was applied to the determination of Ni in waste and mineral waters.     

Solid phase microextraction with gas chromatography-mass spectrometry: a very rapid method for identification of volatile organic compounds emitted by Carum copticum

The investigation of flower scent represents an important field of modern biological research which is directed towards special theories of biological recognition. The headspace solid phase microextraction coupled with gas chromatography-mass spectrometry was used to identify the volatile components of Carum copticum (C. copticum) cultivated in Iran. The compounds were identified according to their retention indices and mass spectra (EI, 70 eV). The effects of different parameters, such as the desorption time, the extraction temperature, the sample mass, the addition of salt, the pre-equilibration time and the extraction time, on the extraction efficiency were investigated. The optimized conditions were: the desorption time, 2 min; the extraction temperature, 58 degrees Celsius; the sample mass, 1.000 g in 4.0 mL 2.0 M NaCl solution; the pre-equilibration time, 25 min; the extraction time, 20 min. Finally, ten components were identified in the volatile components of C. copticum. The major components of C. copticum were thymol (68.2%), gamma-terpinene (13.9%), p-cymene (11.6%), myrcene (1.0%) and beta-pinene (0.6%). Precision of the proposed method is good and %RSD less than 14 was obtained.     

Heat transfer coefficients of shell and coiled tube heat exchangers

In the present study, the heat transfer coefficients of shell and helically coiled tube heat exchangers were investigated experimentally. Three heat exchangers with different coil pitches were selected as test section for both parallel-flow and counter-flow configurations. All the required parameters like inlet and outlet temperatures of tube-side and shell-side fluids, flow rate of fluids, etc. were measured using appropriate instruments. Totally, 75 test runs were performed from which the tube-side and shell-side heat transfer coefficients were calculated. Empirical correlations were proposed for shell-side and tube-side. The calculated heat transfer coefficients of tube-side were also compared to the existing correlations for other boundary conditions and a reasonable agreement was observed.     

Thermodynamic analysis and optimization of air-cooled heat exchangers

In the present study, a thermodynamic second-law analysis was performed to investigate the effects of different geometry and flow parameters on the air-cooled heat exchanger performance. For this purpose, the entropy generation due to heat transfer and pressure loss of internal and external flows of the air-cooled heat exchanger was calculated; and it was observed that the total entropy generation has a minimum at special tube-side Reynolds number. Also, it was seen that the increasing of the tube-side Reynolds number resulted in the rise of the irreversibility of the air-cooled heat exchanger. The results also showed when air-side Reynolds number decreased, the entropy generation rate of the external flow reduced. Finally, based on the computed results, a new correlation was developed to predict the optimum Reynolds number of the tube-side fluid flow.     

Determination of zinc in water samples by flame atomic absorption spectrometry after homogeneous liquid-liquid extraction

In this study, a new and simple homogeneous liquid-liquid extraction (HLLE) method based on a pH-independent phase-separation process was developed using a ternary solvent system [water-tetrabutylammonium ion (TBA ⁺)-chloroform] for the preconcentration of Zn²⁺ ions. A Schiff’s base ligand was used as the chelating agent prior to Zn²⁺ ions extraction. Flame atomic absorption spectrophotometry using acetylene-air flame was used for the quantification of analyte after preconcentration. The phase separation occurred due to ion-pair formation of TBA and perchlorate ion. The sedimented phase was then separated using a 100 μL micro-syringe and diluted to 1.0 mL with ethanol. The sample was introduced into the flame by conventional aspiration. After the optimization of complexation and extraction conditions such as pH 9.0, [ligand] = 1.0 × 10⁻⁵ M, [TBA⁺] = 2.0 × 10⁻² M, 100.0 μL of [CHCl₃] and [CLO₄⁻] = 2.0 × 10⁻² M, a preconcentration factor of 100 was achieved for only 10 mL of the sample. The relative standard deviation was 2.3% (n = 10). The limit of detection was sufficiently low and at ppb level. The proposed method was applied to the extraction and determination of Zn²⁺ in natural water samples with satisfactory results.     

Preparation, characterization, and antimicrobial property of cotton cellulose fabric grafted with poly (propylene imine) dendrimer

Two generations of poly (propylene imine) dendrimer with amino terminated groups (G2- and G5-PPI-NH₂) were grafted on cotton cellulose fabric using cross linking agents (citric or glutaric acids). Fourier transform infrared (FTIR) spectroscopy identified ester groups which were formed between hydroxyl groups of the cotton fabric and carboxylic groups of the cross linking agents. Also, attenuated total reflectance-FTIR (ATR-FTIR) analysis confirmed formation of amide groups between the carboxylic groups of the cross linking agents and the amino end groups of the dendrimers. Nitrogen content (N-content) analysis revealed the presence of the dendrimers on the cotton fabric even after 5 washing cycles. In order to study the dispersion of the PPI dendrimers on the surface of the cotton fabric, field emission scanning electron microscopy (FE-SEM) was performed. The particle size distribution of the G2- and G5-PPI-NH₂ aqueous solutions was also determined by dynamic light scattering (DLS) analysis. Antimicrobial activity of the PPI dendrimer aqueous solutions and the cotton cellulose fabric grafted with the dendrimers was evaluated both quantitatively and qualitatively against Gram-positive bacterium (Staphylococcus aureus), Gram-negative bacteria (Pseudomonas aeruginosa and Escherichia coli) and fungus (Candida albicans). The dendrimer grafted cotton cellulose fabric exhibited a 99 % reduction in bacterial counts against S. aureus, E. coli and C. albicans. The antimicrobial activities of the grafted cotton cellulose fabric with the PPI dendrimers were maintained even after 5 washing cycles.