Piezoelectric property improvement of polyethylene ferroelectrets using postprocessing thermal‐pressure treatment

In this work, biaxially stretched polymer foams with well‐defined cellular structures were prepared from polyethylene via blown‐film extrusion and subjected to corona charging to produce a piezoelectric response. The charging parameters were first optimized in terms of charging voltage and needle distance, as well as the gas type and pressure to investigate their effect on the piezoelectric coefficient (d₃₃). The results show that samples charged under nitrogen (N₂) at 100 kPa had better d₃₃ coefficient than those charged under ambient air or N₂ at 20 kPa. Moreover, 2 different thermal pressure treatments were imposed to obtain an optimized eye‐like cellular structure with different cell aspect ratios (AR). The results showed that when the cells were elongated in both the longitudinal and transverse directions (higher AR), higher d₃₃ coefficients were achieved. From all the samples produced, the best results were obtained for a longitudinal aspect ratio (AR‐L) of 7.1, a transversal aspect ratio (AR‐T) of 4.6, and a relative foam density of 0.52 leading to a d₃₃ coefficient of 935 pC/N. This coefficient was further increased using reverse charging and multilayered films, reaching a maximum of 2550 pC/N. This value is much higher than typical ones reported so far for any polyethylene and polypropylene ferroelectrets. These results could increase the use of polyethylene in piezoelectric applications as these materials are very attractive for the large‐scale production of electret‐based sensors and transducers due to their low cost and easy processing.     

Water Formation in Non-Hydrolytic Sol–Gel Routes: Selective Synthesis of Tetragonal and Monoclinic Mesoporous Zirconia as a Case Study

Several non-hydrolytic sol–gel syntheses involving different precursors, oxygen donors, and conditions have been screened aiming to selectively produce mesoporous t-ZrO₂ or m-ZrO₂ with significant specific surface areas. The in situ water formation was systematically investigated by Karl Fisher titration of the syneresis liquids. XRD and nitrogen physisorption were employed to characterize the structure and texture of the ZrO₂ samples. Significant amounts of water were found in several cases, notably in the reactions of Zr(OnPr)₄ with ketones (acetone, 2-pentanone, acetophenone), and of ZrCl₄ with alcohols (benzyl alcohol, ethanol) or acetone. Conversely, the reactions of Zr(OnPr)₄ with acetic anhydride or benzyl alcohol at moderate temperature (200 °C) and of ZrCl₄ with diisopropyl ether appear strictly non-hydrolytic. Although reaction time and reaction temperature were also important parameters, the presence of water played a crucial role on the structure of the final zirconia: t-ZrO₂ is favored in strictly non-hydrolytic routes, while m-ZrO₂ is favored in the presence of significant amounts of water. ¹H and ¹³C NMR analysis of the syneresis liquids allowed us to identify the main reactions responsible for the formation of water and of the oxide network. The morphology of the most interesting ZrO₂ samples was further investigated by electron microscopy (SEM, TEM).     

Isolation and structure determination of a novel furanic ester from the aerial part of Prasium majus

The aerial part of Prasium majus provided a new furanic ester, 2-2-[(5-formyl-6[(5-formylfuran-2-yl)methoxy] succinic acid dimethyl ester, (+/-)-hiziprafuran. Its structure was principally established by one- and two-dimensional NMR spectroscopy.     

Chemical composition and in vitro antifungal and antioxidant activity of the essential oil and methanolic extract of Teucrium sauvagei Le Houerou

The chemical composition and the in vitro antifungal and antioxidant activity of the essential oil and the methanolic leaf extracts of Teucrium sauvagei Le Houerou, an endemic medicinal plant growing in Tunisia, have been studied. More than 35 constituents having an abundance >or=0.2% were identified in the oil. beta-Eudesmol, T-cadinol, alpha-thujene, gamma-cadinene, and sabinene were the prevalent constituents. Results of the antifungal activity tests indicated that the methanolic extract inhibited the in vitro growth of seven dermatophytes, whereas the essential oil showed average inhibition against only three dermatophytes. In vitro antioxidant properties of the essential oil and the methanolic extract were determined by DPPH (2,2-diphenyl-1-picrylhydrazyl) and ABTS (2,2'-azinobis(3-ethylbenzothiazoline-6-sulphonic acid)) assays and compared to those of the synthetic antioxidant Trolox. Due to their antifungal and antioxidant properties, the essential oil and the methanolic extract of T. sauvagei may be of use as natural preservative ingredients in food and/or pharmaceutical industries.     

Structure-antibacterial activity relationship of secondary metabolites from Ajuga pseudoiva Rob. leaves

A selection of steroids, glycerides, clerodane diterpenoids, and a beta-hydroxy fatty acid methyl ester, all previously isolated from Ajuga pseudoiva leaves, were tested for their antibacterial activity toward three Gram- rods and one Gram+ coccus using the dilution method; MIC values were determined. The results suggested some importance for a free beta-hydroxy group in the fatty acid ester and also in the glycerides and clerodane derivatives; the absolute configurations of the latter, notably at C2, had little influence on activity.     

Mutagenic, antimutagenic and antioxidant activities of a new class of beta-glucoside hydroxyhydroquinone from Anagallis monelli growing in Tunisia

A new skeleton of an O-heteroside natural substance named zinolol, the first representative of a new class of aminated hydroxyhydroquinone, has been isolated from the whole plant Anagallis monelli. Its structure has been established by one and two dimensional NMR spectroscopic procedures. Antioxidant, mutagenic, antimutagenic activities were realised and positive results were recorded.     

Echiofruzine, a novel naringenin diglycoside from Echiochilon fruticosum growing in Tunisia

The aerial parts of the Tunisian plant Echiochilon fruticosum yielded a novel flavonol diglycoside: naringenin-5-O-beta-D-glycopyranoside-3-O-alpha-L-rhamnopyranoside, named Echiofruzine (1), together with the known compounds vomifoliol-9-O-beta-D-glucopyraroside (2), 1-oxo-alpha-ionyl-9-O-beta-D-glucopyranoside (3) and 1-O-[beta-D-xylopyranosyl(1 --> 6)-beta-D-glucopyranosyl] eugenol (4), described for the first time in the indicated plant. The structures of the four isolated compounds were established on the basis of chemical and spectroscopic evidence.     

Parallel Breakup of Polymer Drops under Simple Shear

The deformation and breakup of a single polycarbonate drop in a polyethylene matrix is studied at high temperatures under simple shear flow using a transparent Couette device. We observed “parallel breakup” where the drop breaks after being stretched into a thin sheet parallel to the flow. The breakup occurs at a viscosity ratio greater than 3.5. Deborah number and a stress ratio incorporating elastic moduli can characterize the “parallel breakup”.

Deformation and breakup of a polycarbonate drop in a polyethylene matrix.     

Two new alkaloids and a new polyphenolic compound from <Emphasis Type="Italic">Cotula coronopifolia</Emphasis>

Two new alkaloid derivatives of the 3-benzazocine skeleton (cotuzine A and B) and a new polyphenolic substance (3-(1,3-dihydroxyprop-2-yl)-4-hydroxyanisol) (corimen) have been isolated from the aerial part (stems, leaves) of the plant Cotula coronopifolia (L.). These three new structures were established by spectroscopic procedures (¹H, ¹³C, one- and two-dimensional NMR). The stereochemistry of the new alkaloids was established based on different NOE effects revealed on the NOESY spectrum. Mass spectrometry and IR spectroscopy were used to confirm these structures.     

Electronic Conductive Microporous Polymer‐Based Structures

Summary: This study aims at developing a highly electronic conductive microporous structure from thermoplastic polymers filled with carbon black (CB) and graphite (GR). The matrix was a low viscosity poly(propylene) (PP) and the conductive additives were composed of high specific surface area CB and synthetic flake GR. Conductive blends were first developed using a corotating twin‐screw extruder. Rheological properties and conductivities of these blends were then characterized as a function of blend composition. Blends that show the best compromise between electronic conductivity and processability were subsequently extruded through a sheet die to obtain films of around 500 µm in thickness. These films were then stretched in two successive steps under controlled temperature and stretching rate to generate a film of controlled microporous structure.

TEM of film made from a 50 wt.‐% PP/25 wt.‐% CB/25 wt.‐% GR blend after stretching.