Nanocomposite hydrogel consisting of Na‐montmorillonite with enhanced mechanical properties

A new kind of nanocomposite (NC) hydrogel with Na‐montmorillonite (MMT) is presented in this article. The NC hydrogels were synthesized by free radical copolymerization of acrylamide and (3‐acrylamidopropyl) trimethylammonium chloride (ATC) in the presence of MMT and N,N′‐methylene‐bis‐acrylamide used as chemical cross‐linker. Due to the cation‐exchange reaction between MMT and ATC (cationic monomer) during the synthesis of NC hydrogels, MMT platelets were considered chemical “plane” cross‐linkers, different from “point” cross‐linkers. With increasing amount of MMT, the crosslinking degree enhanced, causing a decrease of the swelling degree at equilibrium. Investigations of mechanical properties indicated that NC hydrogels exhibited enhanced strength and toughness, which resulted from chemical interaction between exfoliated MMT platelets and polymer chains in hydrogels. Dynamic shear measurements showed that both storage modulus and loss modulus increased with increasing MMT content. The idea described here provided a new route to prepare hydrogels with high mechanical properties by using alternative natural Na‐MMT. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1020–1026     

Facile fabrication of fast recyclable and multiple self‐healing epoxy materials through diels‐alder adduct cross‐linker

A reversibly cross‐linked epoxy resin with efficient reprocessing and intrinsic self‐healing was prepared from a diamine Diels‐Alder (DA) adduct cross‐linker and a commercial epoxy oligomer. The newly synthesized diamine cross‐linker, comprising a DA adduct of furan and maleimide moieties, can cure epoxy monomer/oligomer with thermal reversibility. The reversible transition between cross‐linked state and linear architecture endows the cured epoxy with rapid recyclability and repeated healability. The reversibly cross‐linked epoxy fundamentally behaves as typical thermosets at ambient conditions yet can be fast reprocessed at elevated temperature like thermoplastics. As a potential reversible adhesive, the epoxy polymer with adhesive strength values about 3 MPa showed full recovery after repeated fracture‐thermal healing processes. The methodology explored in this contribution provides new insights in modification of conventional engineering plastics as functional materials. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2094–2103     

关于(?)-拟微分核的连续性

Supposa that f(x) is a quasidifferentiable function, defined on S(?)R~n where S is an open set, with a -equivalent bounded quasidifferential subfam ily. Lenma I     

铁分子Fe2的自旋极化效应

采用密度泛函方法(B3P86)对 Fe_2分子结构进行了优化.计算结果中未观察到自旋污染,基态波函数与高态波函数并未混杂,结果表明,Fe_2中有8个未配对电子,这些电子空间分布不同和自旋平行产生的自旋极化效应,使 Fe_2能量最低.计算结果表明,Fe_2分子的基态是~9∑_g~ ,并非~7Δ_u,进而表明 Fe_2的自旋平行效应比电子自旋配对效应要强.计算得到该分子基态的二阶、三阶和四阶力常数分别为1.4115×10~(-2)aJ/nm~2、-37.1751×10~3aJ/nm~3和 98.7596×10~4aJ/nm~4；光谱数据ω_eχ_e、B_e、α_e分别为0.3522、0.0345、 0.4963×10~(-4)cm~(-1)；离解能为3.5522eV,平衡键长为0.2137nm,振动频率为292.914cm~(-1)；并得到了 Murrel-Sorbie 函数.     

Banach空间中优化问题的最优性条件

首先在Contingent切锥意义下界定了Banach空间中非空集合的伪切锥和伪凸性的概念，并讨论了相应的性质，然后针对可微优化问题，在广义凸性假设下，建立了最优性条件。     

Structures and stability of Al<Subscript><Emphasis Type="Bold">7</Emphasis></Subscript>C and Al<Subscript><Emphasis Type="Bold">7</Emphasis></Subscript>N clusters

We report results of the atomic and electronic structures of Al₇C cluster using ab initio molecular dynamics with ultrasoft pseudopotentials and generalized gradient approximation. The lowest energy structure is found to be the one in which carbon atom occupies an interstitial position in Al₇ cluster. The electronic structure shows that the recent observation [Chem. Phys. Lett. 316, 31 (2000)] of magic behavior of Al₇C^- cluster is due to a large highest occupied and lowest unoccupied molecular orbital (HOMO-LUMO) gap which makes Al₇C^- chemically inert. These results have further led us to the finding of a new neutral magic cluster Al₇N which has the same number of valence electrons as in Al₇C^- and a large HOMO-LUMO gap of 1.99 eV. Further, calculations have been carried out on (Al₇N)₂ to study interaction between magic clusters. Received 28 July 2001     

Molecular dynamics simulation of processing using AFM pin tool

A three-dimensional molecular dynamics (MD) model is utilized to investigate the effect of tool geometry on the deformation process of the workpiece and the nature of deformation process at the atomic-scale. Results show that different states exist between the atomic force microscope (AFM) pin tool and the workpiece surface, i.e. the non-wear state, the ploughing state, the state in which ploughing is dominant and the state in which cutting plays a key role. A relationship between the deformation process of the workpiece and the potential energy variation is presented. The potential energy variation of atoms in different deformed regions in the workpiece such as plastically deformed region, elastically deformed region and the mixed deformation region is different. The features of variations of potential energy are discussed.