New insights on amorphous silicon-nitride microcavities

All amorphous silicon-nitride planar optical microcavities operating in the visible range have been grown by plasma enhanced chemical vapor deposition. The luminescence intensity of the N-rich silicon-nitride layer from a microcavity with 6 period distributed Bragg reflectors (DBRs) is two order of magnitude higher than that of the luminescent layer without the cavity. Moreover, a strong directionality of the microcavities emission can be observed. Such results can be ascribed to the anisotropic optical density of states induced in the Fabry–Perot structure. The quality factors of the resonators are strictly correlated to the number of periods of the DBRs.     

Multimodal open-tubular capillary electrochromatographic analysis of amines and peptides

This study describes a comparison of different modes of open-tubular electrochromatography (OTCEC) in bare and etched capillaries. To carry out the investigation, the separation of impurities of two synthetic peptides and the separation of a mixture of five heterocyclic aromatic amines were studied. Three different types of stationary phase were evaluated: (i) fluorosurfactants (anionic and zwitterionic) adsorbed in the inner wall of the capillary (electrochromatography with dynamically modified stationary phases (DMS)CEC); (ii) physically adsorbed polymers (DMA-SO(3-) and DMA-N(+)(CH(3))(3)) and (iii) chemically modified capillaries (C(18), cholesteryl 10-undecanoate and diol). The results confirm that electrochromatography can be a viable alternative to capillary electrophoresis (CE) and liquid chromatography, more established separation techniques. It is possible to differentiate some minor species for the synthetic peptides that cannot be resolved by CE or high-performance liquid chromatography (HPLC). Moreover the separation of the amine mixture depends strongly on the stationary phase used.     

Electrodes/Electrolyte Interfaces in the Presence of a Surface‐Modified Photopolymer Electrolyte: Application in Dye‐Sensitized Solar Cells

Since hundreds of studies on photoanodes and cathodes show that the electrode/electrolyte interfaces represent a key aspect at the base of dye‐sensitized solar cell (DSSC) performances, it is reported here that these interfaces can be managed by a smart design of the spatial composition of quasi‐solid electrolytes. By means of a cheap, rapid, and green process of photoinduced polymerization, composition‐tailored polymer electrolyte membranes (PEMs) with siloxane‐enriched surfaces are prepared, and their properties are thoroughly described. When assembled in DSSCs, the interfacial action promoted by the composition‐tailored PEMs enhances the photocurrent and fill factor values, thus increasing the global photovoltaic conversion efficiency with respect to the non‐modified PEMs. Moreover, the presence of the siloxane‐chain‐enriched surface increases the hydrophobicity and reduces the water vapor permeation into the device, thus enhancing the cell′s durability.     

Radiative emission properties of a-SiN : H based nanometric multilayers for light emitting devices

Optical and photoluminescence characterizations were performed on nanometric multilayer structures based on amorphous silicon nitrogen alloys. Evidences are shown that the radiative efficiency of multilayers increases with respect to single-layer structures. This is ascribed to a strong electron–hole pair localization and a low heterointerfaces defect density. Time-resolved photoluminescence measurements yield fast recombination with an energy-dependent lifetime due to hopping processes. Finally, the performance of an electroluminescent device based on multilayers is presented.     

Methodology in studying improvement of polyacrylates biodegradability

The biodegradability of polyacrylic acid derivatives may be improved through introduction of some fragility points within the main carbon chains. These weakness points can be either hydrolizable bonds or oxidizable sites. Enzymatic hydrolysis and oxydative biomimetic degradation tests have been set up in order to quickly evaluate new polymeric structures, before their possible evaluation through microbial degradation by Candida tropicalis.     

Strain state in bcc Fe films grown on Si(1 1 1)

The strain state of Fe films grown on Si(1 1 1) has been investigated by X-ray diffraction (XRD) in the thickness range between 11 and 304 monolayers. Fe grows tetragonally distorted with the orientation relationship Fe(1 1 1) // Si(1 1 1) . At low coverage, the films grow pseudomorphic. Above 15 monolayers the films are characterized by the coexistence of a pseudomorphic phase with another one which relaxes with the Fe thickness. This relaxation proceeds rapidly in the earlier stages then slowly with the film thickness. The XRD characterization allows one to obtain quantitative information on the in-plane and out-of-plane strains.     

Surface behavior and molecular recognition in DNA microarrays from N,N-dimethylacrylamide terpolymers with activated esters as linking groups

A series of terpolymers made of DMA, NAS and MAPS were synthesized by free radical copolymerization and used as functional coatings for the fabrication of glass slide DNA microarrays. The surface properties of coated glass slides were investigated through contact angle measurements, ellipsometry and atomic force microscopy. The terpolymer molecular weight showed a moderate effect on surface tension (gamma(s) = 56-62 mN x m(-1)), but no clear effect on polymeric layer thickness (5-8 nm) and roughness. Hybridization experiments with amine-functionalized oligonucleotides gave the best fluorescence intensity results for microarrays coated with intermediate-molecular-weight terpolymers. Finally, an accelerated ageing test of the microarray in a humidity chamber showed a nice relationship between decay curves of contact angle against water and fluorescence intensity.