Beta-functionalised polythiophenes as microelectrode modifiers in low conductive media

A study on polythiophene coated microelectrodes is reported, the goal being that of checking the capability of these electrochemical systems to work in low conductive media. The possibility of electrochemically p-doping the polymer in the presence of very low concentrations or even in the absence of supporting electrolyte in the solution is ascertained, opening the way to the use of similar systems in pure solvent media. This result is obtained in such conditions that the presence of residual charges--and corresponding counterions--trapped inside the film coating can be reasonably hypothesised.     

3-methylthiophene self-assembled monolayers on planar and nanoparticle Au surfaces

In this article the adsorption of 3-methylthiophene on planar and nanoparticle Au surfaces is investigated. The resulting systems are compared with a benchmark system based on 1-decanethiol. The characterization data collected evidence the formation of a packed 3-methylthiophene SAM on the planar surface. In particular, spectroscopic investigations suggest that 3-methylthiophene aromatic system is not adsorbed on the surface through the pi-electron system but rather through the S atom alone. On the other hand, the behavior of 3-methylthiophene on nanoparticle surfaces is notably different from that of the alkanethiol. Only a limited fraction of the surface of Au nanoparticles results to be actually coated after purification; this notwithstanding, the nanoparticle growth seems to be strongly influenced by the presence of such a labile encapsulating agent.     

Structure and properties of 1,4-benzenedimethanethiol films grown from solution on Au(1 1 1): An XPS and NEXAFS study

Core level photoemission and X-ray absorption at the carbon C 1s edge are applied to the study of chemisorption of 1,4-benzenedimethanethiol molecules on Au(1 1 1) and to investigate the effect of the solvent used to prepare the organic films. 1,4-Benzenedimethanethiol films were prepared in polar and non-polar solvents, i.e. ethanol, methanol and n-hexane. 1,4-Benzenedimethanethiol molecules are anchored to the substrate through a single S-Au bond; the molecules in the films tend to assume an upright orientation, the aromatic ring resulting tilted towards the direction perpendicular to the substrate plane. The films present an effective thickness corresponding to more than a single layer. Only small differences are observed among behaviours in different solvents. It is concluded that the final properties and conformation of the 1,4-benzenedimethanethiol films are largely determined by the reciprocal interactions between the molecules and with the substrate.     

Temperature and composition dependence of the refractive indices of the 2-chloroethanol + 2-methoxyethanol binary mixtures

Measurements of the refractive index n for the binary mixtures 2-chloroethanol + 2-methoxyethanol in the 0 < or = t/degree C < or = 70 temperature range have been carried out with the purpose of checking the capability of empirical models to express physical quantity as a function of temperature and volume fraction, both separately and together, i.e., in a two independent variables expression. Furthermore, the experimental data have been used to calculate excess properties such as the excess refractive index, the excess molar refraction, and the excess Kirkwood parameter delta g over the whole composition range. The quantities obtained have been discussed and interpreted in terms of the type and nature of the specific intermolecular interactions between the components.     

Electrocatalytic and antifouling properties of CeO2-glassy carbon electrodes

Journal of Solid State Electrochemistry - Binary metal oxides with different degrees of covalent/ionic character of the oxygen-metal bond are tested as a partial coating of glassy carbon electrode...     

PEDOT‐Modified Microelectrodes. Preparation,Characterisation and Analytical Performances

Poly(3,4‐ethylenedioxythiophene) (PEDOT) modified microelectrodes were prepared by electropolymerisation of the relevant monomer from CH₃CN or H₂O solutions. The electrochemical behaviour of the obtained coatings was investigated by cyclic voltammetry in both organic and aqueous media. The anodic responses obtained for a typical benchmark analyte such as ascorbic acid was used to test the different coatings; calibration curves were built up in order to evaluate the repeatability of the response and the reproducibility of the prepared sensing system. Moreover, the ability of the modified microelectrodes to work in low conductivity media was studied, and exploratory tests in dense food matrix was performed.     

EQCM study of the p- and n-doping processes of a poly[4,4-bis(butylsulphanyl)-2,2-bithiophene]

Electrogenerated deposits of poly[4,4^′-bis(butylsulphanyl)-2,2^′-bithiophene] have been characterised in the presence of different supporting electrolytes, by coupling current (charge) to microgravimetric measurements from the electrochemical quartz crystal microbalance (EQCM). The simultaneous collection of voltammetric measurements and of data relative to mass changes shows the influence exerted by the nature of the supporting electrolyte on the charge-discharge steps of both p- and n-doping processes. Interestingly, the microgravimetric data collected corresponding to the pre-peaks of both doping processes suggest the occurrence of two opposite motions of ions (ingress into and exit out from the polymer) in the relevant potential region, giving a contribution to the study of the `residual charge' phenomenon.     

Graphene-modified electrode. Determination of hydrogen peroxide at high concentrations

A gold electrode partially coated by graphene multilayer is developed and tested with respect to high concentrations of hydrogen peroxide. The effective use of conventional electrode materials for the determination of such an analyte by anodic oxidation or cathodic reduction is prevented by the occurrence of adsorptions fouling the electrode surface. This prevents reliable and repeatable voltammetric curves for being recorded and serious problems arise in quantitative analysis via amperometry. The gold–graphene electrode is shown to be effective in quantitative evaluation, by cathodic reduction, of hydrogen peroxide at concentration levels that are of interest in an industrial. Acid, neutral, and basic pH values have been tested through correct adjustment of a Britton Robinson buffer. The experiments have been performed both by cyclic voltammetry and with amperometry at constant potential in unstirred solution. The latter technique has been employed in drawing a calibration linear plot. In particular, the performances of the developed electrode system have been compared with those of both pure gold and pure graphene electrode materials. The bi-component electrode was more sensitive; co-catalytic action by the combination of the two components is hypothesised. The system is stable over many potential cycles, as checked by surface-enhanced Raman spectra recorded over time.     

Unusual metals as electrode materials for electrochemical sensors

Although noble metals are still widely used in electroanalysis, a plethora of different nonconventional metals is now enriching the panorama of materials acting as the electrochemical transducer in sensing systems. In particular, Ti, Cu, Co, Fe, Mo, Ta, W, Rh, Bi, Sb, Te and Pb are discussed here in view of their peculiar physicochemical properties and of the interesting electrocatalytic activities ascribable to these elements and to the relevant metal oxide ultrathin films that spontaneously form at the electrode–solution interface. This behaviour, exploitable in electroanalysis for the detection of a number on analytes, is often accompanied by low price and high resistance to corrosion and to abrasion characterising these materials. These peculiarities encourage the possible use of the cited metals in a wide number of analytical frames, ranging from process control to bioimplantable sensing systems.