WO3–SiO2 nanomaterials synthesized using a novel template-free method in supercritical CO2 as heterogeneous catalysts for epoxidation with H2O2

A series of tungsten oxide-silica (WO₃–SiO₂) composite nanomaterials were synthesized through a novel, template-free sol-gel method, in which supercritical-CO₂ (scCO₂) was utilized as synthesis medium. The efficacy of the synthesis method stems from a tailored reactor design that allows the contact of the reactants only in the presence of scCO₂. Selected synthetic parameters were screened with the purpose of enhancing the performance of the resulting materials as heterogeneous catalysts in epoxidation reactions with H₂O₂ as environmentally friendly oxidant. A cyclooctene conversion of 73% with epoxide selectivity of > 99% was achieved over the best WO₃–SiO₂ catalyst under mild reaction conditions (80 °C), equimolar H₂O₂ amount (1:1) and low WO₃ loading (~2.5 wt%). The turnover number achieved with this catalyst (TON = 328), is significantly higher than that of a WO₃–SiO₂ prepared via a similar sol-gel route but without supercritical CO₂, and that of commercial WO₃. A thorough characterization with a combination of techniques (ICP-OES, N₂-physisorption, XRD, TEM, STEM-EDX, SEM-EDX, FT-IR and Raman spectroscopy, XPS, TGA and FT-IR analysis of adsorbed pyridine) allowed correlating the physicochemical properties of the WO₃–SiO₂ nanomaterials with their catalytic performance. The high catalytic activity was attributed to: (i) the very high surface area (892 m²/g) and (ii) good dispersion of the W species acting as Lewis acid sites, which were both brought about by the synthesis in supercritical CO₂, and (iii) the relatively low hydrophilicity, which was tuned by optimizing the tetramethyl orthosilicate concentration and the amount of basic solution used in the synthesis of the materials. Our optimum catalyst was also tested in the reaction of cyclohexene with H₂O₂, resulting in cyclohexane diol as main product due to the presence of strong Brønsted acid sites in the catalyst, whereas the reaction with limonene yielded the internal epoxide as the major product and the corresponding diol as side product. Importantly, the catalyst did not show leaching and could be reused in five consecutive runs without any decrease in activity.     

Feedstock recycling of polyethylene over AlTUD-1 mesoporous catalyst

The catalytic degradation of high density polyethylene (HDPE) was investigated using AlTUD-1 as catalyst, a recently discovered mesoporous aluminosilicate. The catalytic activity of AlTUD-1 was evaluated by TGA measurements, using a polymer/catalyst ratio of 9:1. AlTUD-1 has a Brønsted acidic behaviour, three-dimensional (3D) connectivities and a pore diameters between 2 and 50 nm. Compared to HY zeolite, the large pore size of AlTUD-1 enhances a selective catalytic degradation of the polymer and prevents rapid deactivation. Moreover, the apparent activation energy of polymer cracking is much lower than with HY zeolite. For these reasons, AlTUD-1 is a potentially interesting catalyst for the catalytic cracking of plastic waste into liquid fuels.     

Titanosilicate beads with hierarchical porosity: synthesis and application as epoxidation catalysts

Porous titanosilicate beads with a diameter of 0.5-1.5 mm (TiSil-HPB-60) were synthesized from a preformed titanosilicate solution with a porous anion-exchange resin as template. The bead format of this material enables its straightforward separation from the reaction mixture in its application as a liquid-phase heterogeneous catalyst. The material displays hierarchical porosity (micro/mesopores) and incipient TS-1 structure building units. The titanium species are predominantly located in tetrahedral framework positions. TiSil-HPB-60 is a highly active catalyst for the epoxidation of cyclohexene with t-butyl hydroperoxide (TBHP) and aqueous H(2)O(2). With both oxidants, TiSil-HPB-60 gave higher epoxide yields than Ti-MCM-41 and TS-1. The improved catalytic performance of TiSil-HPB-60 is mainly ascribed to the large mesopores favoring the diffusion of reagents and products to and from the titanium active sites. The epoxide yield and selectivity could be further improved by silylation of the titanosilicate beads. Importantly, TiSil-HPB-60 is a stable catalyst immune to titanium leaching, and can be easily recovered and reused in successive catalytic cycles without significant loss of activity. Moreover, TiSil-HPB-60 is active and selective in the epoxidation of a wide range of bulky alkenes.     

High-density storage of H2 in microporous crystalline silica at ambient conditions

Molecular hydrogen was encapsulated in the cages of clathrasil decadodecasil 3R (DD3R) during the hydrothermal synthesis of this microporous silicate. The crystalline structure of DD3R facilitates high-density hydrogen storage at ambient conditions. Prompt gamma activation analysis (PGAA) revealed that on average about one molecule of H2 is trapped in each (5(12)) cage of DD3R. The presence of molecular hydrogen inside the DD3R framework was confirmed by solid-state 1H NMR spectroscopy. Temperature-programmed decomposition (TPD) in combination with mass spectrometry showed that the encapsulated hydrogen is released upon decomposition of the clathrasil structure. This release can be promoted by the presence of water.     

Reactions of Podophyllotoxin with DDQ

Introduction 2, 3-Dichloro-5, 6-dicyanobenzoquinone (DDQ) can react with lignans of the mono- arylidene-butyrolactone1, aryltetralin2, dibenzylbutane3 and aryltetralin-butyrolactone4,5 series. We have studied the reactions of this reagent with podophyllotoxin 1, which is a well-known natural product on account of its long history of use in folk medicine and the biological activity of its many derivatives6. In particular, derivatives of 4-demethyl epipodophyllotoxin are used in cancer chemo…     

Transition-metal-free catalysts for the sustainable epoxidation of alkenes: from discovery to optimisation by means of high throughput experimentation

Transition-metal-free oxides were studied as heterogeneous catalysts for the sustainable epoxidation of alkenes with aqueous H?O? by means of high throughput experimentation (HTE) techniques. A full-factorial HTE approach was applied in the various stages of the development of the catalysts: the synthesis of the materials, their screening as heterogeneous catalysts in liquid-phase epoxidation and the optimisation of the reaction conditions. Initially, the chemical composition of transition-metal-free oxides was screened, leading to the discovery of gallium oxide as a novel, active and selective epoxidation catalyst. On the basis of these results, the research line was continued with the study of structured porous aluminosilicates, gallosilicates and silica-gallia composites. In general, the gallium-based materials showed the best catalytic performances. This family of materials represents a promising class of heterogeneous catalysts for the sustainable epoxidation of alkenes and offers a valid alternative to the transition-metal heterogeneous catalysts commonly used in epoxidation. High throughput experimentation played an important role in promoting the development of these catalytic systems.     

Novel transition-metal-free heterogeneous epoxidation catalysts discovered by means of high-throughput experimentation

Various transition-metal-free oxides have been studied as catalysts for the epoxidation of cyclooctene with hydrogen peroxide by means of high-throughput experimentation. Different boron, aluminium, and gallium oxides were prepared according to various synthesis methods. A number of pure aluminium and gallium oxides showed very good catalytic performances, while the results obtained with boron oxides or mixed oxides were less positive. The best results were obtained with a gallium oxide catalyst, which gave an epoxide yield of 71 % and a selectivity of 99 % after reaction for 4 h at 80 degrees C. Gallium oxides had not been reported previously as active epoxidation catalysts. The use of high-throughput experimentation proved useful both for discovering new active catalysts and for identifying a number of relationships between the synthesis conditions and the catalytic properties of the transition-metal-free oxides.