Anisotropic studies of multi-wall carbon nanotube (MWCNT)-filled natural rubber (NR) and nitrile rubber (NBR) blends

50/50 NR/NBR blends with various MWCNT loadings were prepared by mixing with MWCNT/NR masterbatches on a two-roll mill and sheeted off at the smallest nip gap. Then, the effect of milling direction, machine direction (MD) and transverse direction (TD), on the mechanical and electrical properties of the blends was elucidated. Dichroic ratio and SEM results confirmed that most of the MWCNTs were aligned along MD when MWCNT was less than 4 phr, and the number of agglomerates increased when MWCNT was more than 4 phr. Additionally, anisotropic properties were clearly observed when 4 phr MWCNT was loaded. At 4 phr MWCNT, 100% modulus and tensile strength in the MD were about 1.5 and 1.3 times higher than those in the TD, respectively. Moreover, electrical conductivity in the MD was superior to that in the TD by about 3 orders of magnitude. Results from dynamic mechanical tests also showed that the maximum tan δ in the MD sample was lower than that in the corresponding TD sample. In addition, the storage modulus at 30 °C for the MD sample containing 4 phr MWCNT was 1.15 higher than that of the corresponding TD sample. This stronger reinforcement efficiency resulted from the combination of the greater alignment and dispersion of most MWCNTs in the MD sample.     

Raman spectroscopy and thermal analysis of gum and silica-filled NR/SBR blends prepared from latex system

Natural rubber/styrene-butadiene rubber (NR/SBR) blends, with and without silica, were prepared by co-coagulating the mixture of rubber latices and various amounts of well-dispersed silica suspension. An attempt to predict blend compositions was made using Raman spectroscopy in association with differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). It was found that the intensity of each Raman characteristic peak was strongly dependent on the blend composition, but there was no significant evolution with the presence of silica. Also, TGA results revealed an improvement in thermal stability of NR/SBR blends with increasing both SBR and silica contents due to the dilution effect. Two distinct glass transition temperatures (T_g) were observed in DSC thermograms of all blends, and their T_g values were independent on both blend composition and silica content. This indicated a physical blend formation, which agreed well with no shifts in Raman peaks of the blends in comparison with those of the individual rubbers. Linear regression with R² quality factor close to 0.99 was achieved when plotting intensity ratio at 1371/1302 cm^?1 versus blend ratios. On the other hand, the peak height ratio and heat capacity ratio from TGA and DSC analysis, respectively, yielded quadratic equations as a function of blend ratios.     

New reference material for analysis of elements in glutinous rice produced at the National Institute of Metrology (Thailand)

Reference materials play an important role for evaluating the accuracy of analytical results, and are essential parts of good laboratory practice. They represent a key tool for quality control of chemical analyses. In Thailand, the demand of food and environmental reference materials is constantly increasing, and the National Institute of Metrology (NIMT, Thailand) is responding to the urgent needs for affordable materials, which require collaborative efforts at the national level. This paper describes the preparation of a new glutinous rice reference material, along with homogeneity and stability studies and the analytical work carried out for the certification of the contents of inorganic elements. The incurred material was collected from an actual rice paddy field. Material preparation along with homogeneity and stability testing were carried out at the Environmental Research Training Centre (ERTC). The homogeneity study was designed to have three experimental conditions; (A) 10 bottles of candidate materials being analyzed each with 2 replicates, (B) 20 bottles with 2 replicates, (C) 10 bottles with 7 replicates, in order to study the suitable treatments for homogeneity testing in the reference material production. It was shown that a minimum number of 10 bottles with duplicate analyses are enough to demonstrate the homogeneity of candidate reference material. Certification of a candidate reference material in a single laboratory using reference method was confirmed with an interlaboratory comparison participated by a certain number of well recognized testing laboratories in Thailand. Further elaborative results will be discussed.     

Magnetic nanoparticle formulations for DNA and siRNA delivery

Newly synthesized magnetic nanomaterials possess high DNA binding capacity either itself or in the presence of a positively charged lipid-based Metafectene™ reagent or branched polyethylene imine 25 kDa. Polyethylene imine (PEI)-modified nanomaterials are able to deliver nucleic acids in cell culture in duplexes. Magnetofection with triplexes of nanomaterials results in higher transduction efficiencies compared to optimal PEI or Metafectene formulations. 90% transient down-regulation of the target protein in HeLa-green fluorescence protein cells was achieved at short interfering RNA concentrations as low as 8 nM with a formulation of PEI-modified nanoparticles.     

Comparison of the mechanical properties at similar hardness level of natural rubber filled with various reinforcing-fillers

Commercially, the alteration of a rubber formulation is usually made in such a way as to keep the hardness of the rubber product constant. This is because a specific hardness of the rubber product sets the limit to its practical applications. Therefore, in this paper, natural rubber (NR) vulcanizates containing various fillers were prepared to have the same hardness level, and their mechanical properties were compared and related to the degree of filler dispersion. The results show that higher amounts of carbon black (CB) and silica are needed for CB- and silica-filled natural rubber vulcanizates to achieve the same hardness value as a NR vulcanizate containing 6 phr of montmorillonite clay. At equal loading of fillers, clay-filled vulcanizate exhibits higher modulus, hardness, tensile strength and compression set, but lower heat build-up resistance and crack growth resistance than those of the vulcanizates containing conventional fillers. For the vulcanizate having the same hardness value, CB-filled vulcanizate gives the better overall mechanical properties followed by the clay-filled and silica-filled vulcanizates, respectively. The explanation is given as the better dispersion of carbon black, as can be seen in the SEM micrograph.     

Quercetin-Rich Ethanolic Extract of Polygonum odoratum var Pakphai Leaves Decreased Gene Expression and Secretion of Pro-Inflammatory Mediators in Lipopolysaccharide-Induced Murine RAW264.7 Macrophages

Polygonum odoratum var. Pakphai has been used in traditional Thai medicine for the treatment of flatulence and constipation and to relieve the inflammation caused by insect bites. Quercetin (Q), which is abundant in plant-based foods, has been found to exert anti-inflammatory properties. This study evaluated the anti-inflammatory activity of P. odoratum ethanolic extract in RAW264.7 macrophage cells. Leaves were extracted with 50% ethanol, phenolics and flavonoids were then analyzed using UHPLC-QTOF-MS and HPLC-DAD. RAW264.7 cells were induced with lipopolysaccharides (LPSs). They were then treated with the extract and prostaglandin E₂ (PGE₂), and interleukin-6 (IL-6) and tumor necrotic factor-alpha (TNF-α) concentrations were determined. Levels of cyclooxygenase-2 (COX-2), inducible nitric oxide synthase (iNOS), IL-6 and TNF-α mRNAs were analyzed using qRT-PCR. Chemical analysis demonstrated that the extract was abundant with Q while also containing catechin, gallic acid, epicatechin gallate and coumarin. The extract increased the viability of RAW264.7 cells and dose-dependently decreased nitric oxide production, PGE₂, IL-6 and TNF-α levels in the medium from the LPS-induced RAW264.7 cell culture. Consistently, COX-2, iNOS, IL-6 and TNF-α mRNA levels were decreased in a concentration-dependent manner (p < 0.05). Thus, the quercetin-rich ethanolic extract derived from P. odoratum var Pakphai leaves can exert anti-inflammatory activity in LPS-induced RAW264.7 cells through a reduction of the pro-inflammatory mediator response.     

Relationship among mechanical properties,heat ageing resistance,cut growth behaviour and morphology in natural rubber: Partial replacement of clay with various types of carbon black at similar hardness level

In this experiment, various types of carbon black (CB) were employed to partially substitute the calcined clay for preparing natural rubber (NR) compounds of similar hardness. At similar hardness, the compounds containing both clay and CB give the better tensile strength, edge-cut tensile strength, tear strength and thermal ageing resistance compared to the control, but the control had better gas barrier property. In addition, the cracking behaviour of the vulcanizate has a transition from simple lateral growth to oblique crack with partial substitution of the clay with CB, and the vulcanizate containing N330 exhibits the greatest longitudinal cracking corresponding to its highest edge-cut tensile strength. This means the presence of N330 causes the greater orientation of the NR chains along the applied force. Furthermore, the vulcanizate containing N330 yields the highest tensile and tear strength, and lowest resilience, although it has the lowest volume fraction of filler. The explanation is given as the higher reinforcing efficiency of N330 and the better filler dispersion shown in SEM micrographs.