Speciation Analysis of Cr(III) and Cr(VI) after Solid Phase Extraction Using Modified Magnetite Nanoparticles

A new solid phase extraction (SPE) method has been developed for the speciation of Cr(III) and Cr(VI). This method is based on the adsorption of Cr(VI) on modified alumina‐coated magnetite nanoparticles (ACMNPs). Total chromium in different samples was determined as Cr(VI) after oxidation of Cr(III) to Cr(VI) using H₂O₂. The chromium concentration has been determined by flame atomic absorption spectrometric (FAAS) technique and amount of Cr(III) was calculated by substracting the concentration of Cr(VI) from total chromium concentration. The effect of parameters such as pH, amount of adsorbent, contact time, sample volume, eluent type, H₂O₂ concentration and cetyltrimethylammonium bromide (CTAB) concentration as modifier on the quantitative recovery of Cr(VI) were investigated. Under the optimal experimental conditions, the preconcentration factor, detection limit, linear range and relative standard deviation (RSD) of Cr(VI) were 140 (for 350 mL of sample solution), 0.083 ng mL^?1, 0.1‐10.0 ng mL^?1 and 4.6% (for 5.0 ng mL^?1, n = 7), respectively. This method avoided the time‐consuming column‐passing process of loading large volume samples in traditional SPE through the rapid isolation of CTAB@ACMNPs with an adscititious magnet. The proposed method was successfully applied to the determination and speciation of chromium in different water and wastewater samples and suitable recoveries were obtained.     

Development of poly(vinyl chloride)/montmorillonite nanocomposites using chelating agents

Different chelating agents such as poly(ethylene glycol), propylene glycol monooctadecanoate and palm oil were used for modification of the surface-treated montmorillonite (MMT). The work also included the development of a technique for mixing chelating agents with MMTs using different methods and different proportions of MMT/chelating agent/ethanol. Evaluation of the result of mixing was performed by thermogravimetric analysis, X-ray diffraction and high-resolution scanning electron microscopy (HR-SEM). The results showed that the chelating agents used were intercalated in MMT, increasing the interlayer spacing. The OMMT was used in the manufacture of composites with rigid PVC using a microcompounder. The master batch concept turned out to be promising in terms of dispersion and delamination of clay, as observed in HR-SEM photographs. However, despite good dispersion and exfoliation of MMT, poor compatibility between clay platelets and PVC matrix remains to be solved to enable full exploitation of its engineering potential. Despite this drawback, good thermal stability and mechanical properties have already been achieved.     

Post modification of zinc based coordination polymer to prepare Zn‐Mo‐ICP nanoparticles as efficient self‐supported catalyst for olefin epoxidation

Preparation, characterization, and catalytic properties of bimetallic coordination polymer constructed from 2‐aminoterephthalic acid as linker, zinc cations as node, and cis‐dioxo molybdenum units as catalytic active sites are reported via two pathways. Molybdenum centers were placed in N,O positions created by condensation reaction of 2‐aminoterephthalic acid with salicylaldehyde while zinc cations coordinated via carboxylic acid groups of linker to achieve infinite chains of metalo‐ligand. The obtained coordination polymer was fully characterized and its catalytic properties in the epoxidation of olefins with tert‐butyl hydroperoxide (TBHP) described. In comparison with previously reported heterogenized molybdenum catalysts, this new coordination polymer exhibited good conversion as well as high selectivity in the epoxidation of olefins. The catalyst is stable under ambient conditions and could be reused as active catalyst for at least five times.     

A modified reaction for the preparation of amidoalkyl naphthols

An efficient synthesis of amidoalkyl naphthols using FeCl₃·SiO₂ as a heterogeneous catalyst is described. This thermal solvent-free procedure offers advantages such as shorter reaction times, simple work-up, excellent yields, and recovery and reusability of the catalyst.     

Silica supported perchloric acid (HClO4-SiO2): an efficient and recyclable heterogeneous catalyst for the one-pot synthesis of amidoalkyl naphthols

An efficient and direct protocol for the preparation of amidoalkyl naphthols employing a multi-component and one-pot condensation reaction of 2-naphthol, aromatic aldehydes, and acetonitrile or acetamide in the presence of silica supported perchloric acid under solvent, solvent-free, and microwave irradiation conditions is described. The present protocol with HClO₄-SiO₂ catalyst is superior to the recently reported catalytic methods. It is noteworthy that 1-amidomethyl-2-naphthols can be converted into important ‘drug like’ 1-aminomethyl-2-naphthol derivatives by amide hydrolysis.     

Study of the Effects of N Fertilization and Plant Density on the Essential Oil Composition and Yield of Cuminum cyminum L. Seeds by HS–SME

Headspace-solvent microextraction (HS–SME) with sample ultrasound irradiation was successfully used for the study of the influence of nitrogen fertilization and plant density on the essential oil yield and composition of cumin (Cuminum cyminum L.) seeds. The components were collected into a single microdrop of n-heptadecane and directly injected into a GC–MS injection port for analysis. A simplex method was used for fast optimization of the extraction parameters. The experiments were executed as split-plot based on randomized complete block design. Nitrogen fertilization as the main factor (in four levels) and plant density as subsidiary factor (in three levels) were applied. It was shown that the total GC peak areas of the HS–SME extract, is proportional to the essential oil yield of the cumin seeds obtained by a hydrodistillation method. Furthermore, similar trends in the concentrations of cuminaldehyde and most other volatile components were obtained by the two methods.