基于吸收系数的生脉注射液中聚山梨酯80含量测定新方法

聚山梨酯80又名吐温80，为一种亲水型非离子表面活性剂，是食品、保健品和药品中常用的辅料，作为增溶剂和澄清剂广泛用于中药注射剂。近年来，不良反应的发生使得聚山梨酯80的质量和应用愈加受到重视，有研究认为其加入可能引起注射剂不良反应增加。为避免超量使用，有必要对该辅料的投料加以严格控制。中药注射剂中聚山梨酯80的含量测定是当下研究的热点和难点，可以通过分光光度法、分子排阻-蒸发光散射检测法(SEC-ELSD)、液质联用法(LC-MS)直接测定，也可以水解后法经液相色谱-紫外检测法(HPLC-UV)或气相色谱法(GC)间接测定。但由于聚山梨酯80为聚氧乙烯聚合数目不同的混合物、不同厂家生产的聚山梨酯80化学组分及比例存在较大差异，难以采用统一的转换公式或对照品准确定量。此外，中药注射剂的复杂基质造成的假阳性干扰也对定量提出了挑战。为解决以上问题，以生脉注射液为例，提出基于吸收系数的中药注射剂中聚山梨酯80含量测定新方法。优化检测波长、显色剂种类、液液萃取过程振荡和静置时间，在6个不同品牌仪器上测得聚山梨酯80-硫氰酸钴配合物的吸收系数(E1%_{1 cm})为104.23，相对标准偏差(RSD)为2.08%。生脉注射液稀释10倍后，精密量取供试品溶液1.0 mL，精密加入硫氰酸钴溶液10 mL，二氯甲烷20 mL，涡旋振荡3 min。将混合液移至分液漏斗中，静置30 min，取下层二氯甲烷液，将前1 mL弃去，接收约15 mL，在320 nm处测定吸光度，再根据Lambert-Beer定律，利用获得的吸收系数计算得到聚山梨酯80的含量。方法阴性无干扰，精密度和重复性相对标准偏差均低于3%，平均回收率为98.42%。为进一步验证方法的准确性，分别采用吸收系数法和标准曲线法测定了2个厂家的10批生脉注射液，并与实际投料量比较。配对t检验结果表明，当置信度为95%时，两种方法无显著性差异，吸收系数法测得结果与企业生产中聚山梨酯的实际投料量也无显著性差异。研究采用前人未采用的、灵敏度更高的320 nm为检测波长，显著降低了基质干扰，克服了中药注射剂中聚山梨酯80测定结果与实际投料量难以吻合的问题。吸收系数法无需使用对照品，亦不用制备标准曲线，可为中药注射剂中聚山梨酯80的检查标准提供切实可行的解决方案。所建方法灵敏、准确、快速、简便，为含聚山梨酯80制剂的质量控制提供了关键常数及新的思路。     

用等厚干涉测定液体折射率

介绍一种采用等厚干涉原理测定液体折射率的简单可靠的方法。     

拉曼放大器中放大的自发拉曼散射与拉曼开-关增益关系的研究

研究了拉曼放大器中放大的自发拉曼散射对拉曼开－关增益的影响，并提出了一种利用自发拉曼散射谱来调整拉曼放大器位曼开－关增益平坦的方法，实验采用4个波长为14xx nm的激光二极管作为抽运源，75km的G．652光纤作为传输介质，获得了C波段附近的光放大，同时对此给出了合理的理论解释。     

半导体激光器发射光谱实验仪

设计了一种半导体激光器发射光谱实验仪 ,可以用来观测LD发射的荧光光谱、激光光谱 ,以及了解光栅外腔选取单纵模、压窄线宽、波长调谐的机理 .该实验仪结构紧凑 ,物理概念清晰 ,适用于大专院校的光学实验教学     

Living/controlled radical copolymerization of N‐substituted maleimides with styrene in 1‐butyl‐3‐methylimidazolium hexafluorophosphate and anisole

The atom transfer radical copolymerization of N‐substituted maleimides such as N‐phenylmaleimide (PhMI), N‐cyclohexylmaleimide (ChMI), and N‐butylmaleimide (NBMI) with styrene initiated with dendritic polyarylether 2‐bromoisobutyrates in an ionic liquid, 1‐butyl‐3‐methylimidazolium hexafluorophosphate ([bmim][PF₆]), at room temperature and anisole at 110 °C was investigated. The dendritic‐linear block copolymers obtained in ionic liquid possessed well‐defined molecular weight and low polydispersity (1.05 < M_w/M_n < 1.32) and could be used as a macroinitiator for chain‐extension polymerization, suggesting the living nature of the reaction system. The ionic liquids containing catalyst could be recycled in the atom transfer radical polymerization systems without further treatment. Compared with polymerization conducted in anisole, the polymerization in ionic liquid had a stronger tendency for alternation. The tendency for alternation decreased in the order PhMI > NBMI > ChMI in [bmim][PF₆] and PhMI > ChMI > NBMI in anisole. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2156–2165, 2003     

Behavior and surface energies of polybenzoxazines formed by polymerization with argon,oxygen, and hydrogen plasmas

Polybenzoxazine (PBZZ) thin films can be fabricated by the plasma‐polymerization technique with, as the energy source, plasmas of argon, oxygen, or hydrogen atoms and ions. When benzoxazine (BZZ) films are polymerized through the use of high‐energy argon atoms, electronegative oxygen atoms, or excited hydrogen atoms, the PBZZ films that form possess different properties and morphologies in their surfaces. High‐energy argon atoms provide a thermodynamic factor to initiate the ring‐opening polymerization of BZZ and result in the polymer surface having a grid‐like structure. The ring‐opening polymerization of the BZZ film that is initiated by cationic species such as oxygen atoms in plasma, is propagated around nodule structures to form the PBZZ. The excited hydrogen atom plasma initiates both polymerization and decomposition reactions simultaneously in the BZZ film and results in the formation of a porous structure on the PBZZ surface. We evaluated the surface energies of the PBZZ films polymerized by the action of these three plasmas by measuring the contact angles of diiodomethane and water droplets. The surface roughness of the films range from 0.5 to 26 nm, depending on the type of carrier gas and the plasma‐polymerization time. By estimating changes in thickness, we found that the PBZZ film synthesized by the oxygen plasma‐polymerization process undergoes the slowest rate of etching in CF₄ plasma. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4063–4074, 2004     

光纤光栅选频掺Yb3+双包层光纤激光器

利用相位掩模法 ,在D形内包层掺Yb3 双包层光纤一端直接写制出Bragg光栅 ,用作双包层光纤激光器的输出腔镜 .试验得到了线宽为 0 196nm ,波长为 10 5 8 2nm ,最高输出功率为 5 70mW的稳定激光输出 ,解决了激光器中模式竞争造成的输出不稳定现象 .从速率方程出发 ,对激光器的输出功率与抽运功率、光栅反射率的关系以及最佳光纤长度进行了理论分析 ,结果与实验符合很好     

硅光电二极管激光损伤阈值随激光脉宽的变化

 对飞秒激光辐照下硅光电二极管损伤阈值进行了实验测量，对从1s到60fs不同脉宽激光辐照下硅光电二极管损伤阈值进行了讨论。实验数据表明，在1s到10ns脉宽范围内损伤所需能量密度近似而非严格地与脉宽的平方根成正比。信号分析表明硅光电二极管的损伤主要由热效应造成，而60fs激光辐照下的损伤阈值为0.1J/cm2，明显偏离普通温度分布预言的趋势。