Determination of inorganic selenium species in water and garlic samples with on-line ionic liquid dispersive microextraction and electrothermal atomic absorption spectrometry

A non-chromatographic separation and preconcentration method for Se species determination based on the use of an on-line ionic liquid (IL) dispersive microextraction system coupled to electrothermal atomic absorption spectrometry (ETAAS) is proposed. Retention and separation of the IL phase was achieved with a Florisil^®-packed microcolumn after dispersive liquid-liquid microextraction (DLLME) with tetradecyl(trihexyl)phosphonium chloride IL (CYPHOS^® IL 101). Selenite [Se(IV)] species was selectively separated by forming Se-ammonium pyrrolidine dithiocarbamate (Se-APDC) complex followed by extraction with CYPHOS^® IL 101. The methodology was highly selective towards Se(IV), while selenate [Se(VI)] was reduced and then indirectly determined. Several factors influencing the efficiency of the preconcentration technique, such as APDC concentration, sample volume, extractant phase volume, type of eluent, elution flow rate, etc., have been investigated in detail. The limit of detection (LOD) was 15 ng L⁻¹ and the relative standard deviation (RSD) for 10 replicates at 0.5 μg L⁻¹ Se concentration was 5.1%, calculated with peak heights. The calibration graph was linear and a correlation coefficient of 0.9993 was achieved. The method was successfully employed for Se speciation studies in garlic extracts and water samples.     

Characterization of HDPE /Polyamide 6/ Nanocomposites Using Scanning-and Transmission Electron Microscopy

Summary: Preparation and morphology of high density polyethylene (HDPE)/ polyamide 6 (PA 6)/modified clay nanocomposites were studied. The ability of PA 6 in dispersing clays was used to prepare modified delaminated clays, which were then mixed with HDPE. Mixing was performed using melt processing in a torque rheometer equipped with roller rotors. After etching the materials with boiling toluene and formic acid at room temperature, the morphology was examined by SEM analyses, showing that the PA 6 formed the continuous phase and HDPE the dispersed phase. X-ray diffraction patterns show that the (001) peak of the clay is dramatically decreased and shifted to lower angles, indicating that intercalated/exfoliated nanocomposites are obtained. TEM analyses confirmed the typical structure of exfoliated nanocomposites. A scheme for the mechanism of exfoliation and/or intercalation of these HDPE /PA 6/ /organoclay nanocomposites is proposed.     

Synthesis of Additives from Montmorillonite to Modify High Density Polyethylene Final Properties

Summary: This work brings about the modification of sodium montmorillonite clay (MNa) by the cationic exchange with hexadecyltrimethylammonium to turn it into organophilic clay (MC₁₆). Subsequently, MC₁₆ was treated with silanes. Three silanes with functional groups of different chemical nature were used. The objective was to determine if the clay could affect high density polyethylene (HDPE) final behavior after being modified with each silane. The following silanes were used: Cl₂Si(CH₃)₂, Cl₂Si(CH₃)(C₆H₅) and Cl₂Si(C₆H₅)₂. Finally, in situ hydrolysis was carried out to generate the respective siloxanes. These materials were characterized by XRD, FTIR and GPC analyses. Each one of these additives was mixed using melt compounding processing in a Haake torque rheometer Rheocord 9000 equipped with a mix chamber and roller rotors at 100 rpm and 190 °C. All hybrids were characterized by XRD, SEM and thermogravimetric analyses. Barrier properties to cyclohexane were also determined by pervaporation experiments. Results from all studies showed that the addition of approximately 3 wt% of clay has changed the macroscopic properties of the above-mentioned composites, as compared with pure HDPE. This can be explained considering the different polymer/filler interactions which take place in each system.     

Magnetoelectric effect in cobalt ferrite-barium titanate composites and their electrical properties

CoFe₂O₄-BaTiO₃ composites were prepared using conventional ceramic double sintering process with various compositions. Presence of two phases in the composites was confirmed using X-ray diffraction. The dc resistivity and thermoemf as a function of temperature in the temperature range 300 K to 600 K were measured. Variation of dielectric constant (ɛ′) with frequency in the range 100 Hz to 1 MHz and also with temperature at a fixed frequency of 1 kHz was studied. The ac conductivity was derived from dielectric constant (ɛ′) and loss tangent (tan δ). The nature of conduction is discussed on the basis of small polaron hopping model. The static value of magnetoelectric conversion factor has been studied as a function of magnetic field.     

Raman and surface enhanced Raman scattering of a black dyed silk

The Raman and surface enhanced Raman scattering (SERS) spectra of a black dyed silk sample (BDS) were registered. The spectral analysis was performed on the basis of Raman and SERS spectral data of isolated samples of Bombyx mori silk fibroin, its motif peptide component (GAGAGS) and the synthetic reactive black 5 dye (RB5). The macro FT‐Raman spectrum of the silk sample is consistent with a silk II‐Cp crystalline fraction of Bombyx mori silk fibroin; the SERS spectrum is highly consistent with conformational modifications of the fibroin due to the interactions with the Ag nanoparticles. The GAGAGS peptide sequence dominates the Raman spectrum of the silk. The SERS spectrum of the peptide suggests a random coil conformation imposed by the surface interaction; the serine residue in the new conformation is exposed to the surface. Quantum chemical calculations for a model of the GAGAGS–Ag surface predict a nearly extended conformation at the Ag surface. The Raman spectrum of the dye was analysed, and a complete band assignment was proposed; it was not possible to propose a preferential orientation or organization of the molecule on the metal surface. Quantum chemical calculations for a model of the dye interacting with a silver surface predict a rather coplanar orientation of the RB5 on the Ag metal surface. The Raman spectrum of the BDS sample is dominated by signals from the dye; the general spectral behaviour indicates that the dye mainly interacts with the silk through the sulphone (–SO₂–) and sulphonate (–SO₂–O–) groups. Besides the presence of dye signals, mainly ascribed to the sulphone and sulphonate bands, the SERS spectrum of the BDS sample also displays bands belonging to the amino acids alanine, glycine, serine and particularly tyrosine. Copyright © 2013 John Wiley & Sons, Ltd.     

Introducing axial chirality into mesoionic 4,4'-bis(1,2,3-triazole) dicarbenes

Mesoionic 4,4'-bis(1,2,3-triazole-5,5'-diylidene) Rh(I) complexes having a C2 chiral 4,4'-axis were accessed from 3-alkyltriazolium salts in virtually complete de. Their structure and configurational integrity were assessed by NMR spectroscopy, X-ray crystallography, and chiral HPLC. Computational analysis of the MICs involved in the reaction suggested the formation of a highly stable and unprecedented cation-carbene intermediate species, which could be evidenced experimentally by cyclic voltammetry analysis.