Emission and sputtering characteristics of Ne-Ar mixed gas glow discharge plasmas.

The emission characteristics of several Cu lines emitted from a Ne-Ar mixed gas glow discharge plasma were investigated. The addition of small amounts of Ar to a Ne plasma increases the sputtering rate of a Cu sample because Ar ions, which work as the impinging ions for cathode sputtering, are predominantly produced through Penning ionization collisions between Ne metastables and Ar atoms. Ar addition also elevates the number density of electrons in the plasma. These changes occurring in the Ne-Ar mixed gas plasma result in enhanced emission intensities of the Cu lines. The Cu II 270.10-nm and the Cu II 224.70-nm lines yield different intensity dependence on the Ar partial pressure added. This phenomenon is because these Cu II lines are excited principally through different charge transfer processes: collisions with Ne ions for the Cu II 270.10-nm line and collisions with Ar ions for the Cu II 224.70-nm line. The shape of sputtered craters in the Ne-Ar glow discharge plasma was measured. The depth resolution was improved when Ar was added to a Ne plasma because the crater bottoms were flatter with larger Ar partial pressures.     

Emission characteristics of Cu in Dc voltage modulation applied glow discharge optical emission spectrometry.

In order to obtain the depth profile of a thin film, we investigated the emission characteristics of a voltage modulation glow discharge to optimize the modulation parameters (modulation voltage, offset voltage, and modulation frequency). In this study, a phase-sensitive detection method with a lock-in amplifier to the modulation technique led to a higher sensitivity and a larger signal-to-noise ratio in the emission analysis compared to the normal dc amplification method. Upon increasing the maximum voltage, the emission intensity of the Cu atomic line (CuI 239.34 nm) increased linearly at a modulation voltage of 400 V and an offset voltage of 300 V. On the other hand, the emission intensity was gradually reduced when a modulation frequency increased. It is advantageous for surface analysis that the voltage modulation technique gives a lower sputtering rate rather than the conventional dc discharge.     

Accurate and rapid estimation on spectral interferences in routine analysis by ICP-AES: use of mutual interference coefficients

A practical method to estimate spectral interferences and to select optimum analytical lines in ICP-AES is suggested. Depending on the matrix composition and the amounts of the analyte, the analytical lines suffering from little interferences and the limit of determination can be determined from calculation using spectral interference coefficients. For this calculation, the spectral interference coefficients, which are defined as apparent mass of the analyte equivalent to the spectral interference from unit mass of the interferent, are obtained experimentally for 639 emission lines of 68 elements. There is a good correlation between the coefficients obtained on two spectrometers having different resolutions.     

Selective excitation of singly-ionized silver emission lines by Grimm glow discharge plasmas using several different plasma gases

The relative intensities of silver emission lines from Grimm glow discharge plasmas were investigated in the wavelength range from 160 to 600 nm when using different plasma gases. It was characteristic of the plasma excitation that the spectral patterns were strongly dependent on the nature of the plasma gas employed. Intense emission lines of silver ion were observed when argonhelium mixed gases were employed as the plasma gas. Selective excitation of the ionic lines could be principally attributed to the charge transfer collisions between silver atoms and helium ions.     

Stabilization of the spark-discharge point on a sample surface by laser irradiation for steel analysis.

A combined technique with laser irradiation is suggested to control spark discharge for analytical use, having a unique feature that firing points of the spark discharge can be fixed by laser irradiation. Because the spark discharge easily initiates at particular surface sites, such as non-metallic inclusions, called selective discharge, the concentration of some elements sometimes deviates from their average one in spark discharge optical emission spectrometry. Therefore, stabilization of firing points on a sample surface could improve the analytical precision.     

Molecular-shape recognition of polycyclic aromatic hydrocarbons in reversed phase liquid chromatography

Summary The molecular-shape recognition of polycyclic aromatic hydrocarbons has been studied on various stationary phases in reversed-phase high-performance liquid chromatography. The examined stationary phases were phenyl-, diphenyl-, triphenyl- and benzyl-bonded silicas. The results of regression analysis inidcated that triphenylsilica is the best packing material to recognize the difference in the molecular-shape of structural isomers. This fact was confirmed by the separation of 4-ring isomers.     

Polydimethylsiloxane connection for quartz microchips in a high-pressure system.

An interconnecting technique, the "PDMS connection method", for quartz microchips in a high-pressure system is presented. The connection between quartz microchips is an essential technology for modular microfluidic devices, such as microchip-HPLC. PDMS was applied to the seal material, being spread on the seal side of the chips, and set into the metal housing. The characteristics of the PDMS connection method concerning pressure resistance and the extension of the peak were examined. The experimental results showed a good seal at 5 MPa, which seem to be sufficient for realizing microchip-HPLC utilizing a monolithic silica capillary column as a separation medium. The influence of the extra column effect on chromatographic separation was almost the same as in the case using a commercial union fitting. In addition, the PDMS connection enabled the detachability of chip-based modules with user-friendliness. Our experimental findings suggest that the novel PDMS connection method can possibly be applied as a generic technology in high-pressure microTAS.     

Emission characteristics of high-powered microwave induced plasma optical emission spectrometry by using nitrogen–oxygen mixture gas

A high-powered, microwave-induced nitrogen–oxygen plasma (N₂–O₂–MIP) generated by using an Okamoto cavity at atmospheric pressure was investigated when the observation height, the flow rate of carrier gas, and the oxygen content were varied as the experimental parameters. The emission characteristics of the plasma were evaluated with regard to the excitation temperature and the intensity ratio of atomic line to ionic line. The excitation temperature of the N₂–O₂–MIP was in the range of 5100–5700 K when the oxygen content was varied from 0 to 30% at the observation height of 7 mm and the carrier gas flow rate of 0.6 l/min. The intensity ratio of atomic line to ionic line was elevated with an increase in the oxygen content.     

Snytheses of analgesics. Part XXXVII. An alternative synthesis of 1,2,3,4, 5, 6-hexahydro-8-hydroxy-2,6-methano-6, h-dimethyl-3-phenethyl-3-benzazoeine [studies on the syntheses of heterocyclic compounds. Part DXXI]

Acid treatment of the alkylated products of (Va, Vb, and VIII) of piperidinols IVa and IVb, and tetrahydropyridine VII with β-bromoethylbenzene, afforded 1,2,3,4,5,6-hexahydro-8-hydroxy-2,6-methano-6,1 1-dimethyl-3-phenethyl-3-benzazocine (la) in good yield. Piperidinols Va and Vb were also obtained from the reaction of N-(3-methyl-3-pentenyl)-β-phenethylamine (IIb) with methyl 3-(4-methoxyphenyl)-2,3-epoxypropionate.     

Development of miniaturized multi-channel high-performance liquid chromatography for high-throughput analysis

We have developed miniaturized multi-channel high-performance liquid chromatography (HPLC) system. With this system, we can simultaneously separate multiple samples, using a single high-pressure gradient pump, a chip-based sample injection unit, a monolithic silica capillary column array, and a multi-channel UV detection unit based on fiber optics. The injection unit has a simplified structure composed of brass housing and a quartz microchip having microchannels and access ports, which enable a direct injection of sample to multi-channel by commercial multichannel micropipette. Moreover, that possesses a function of microvalve, and on-chip definition of sample injection plugs achieved with a cross channel injection method, providing each column of monolithic silica capillary array. The substances in channels were simultaneously detected with UV having multiple cells. Standard samples were analyzed for characterizing newly developed system, and sharp peaks were obtained with reproducibility data of < 0.9% (R.S.D.). Analysis of tryptic digestion of casein was also employed. These results show that the novel multi-channel HPLC system has the benefits for the high-throughput analysis in the post-genomic analysis/combinatorial chemistry.