Nanocomposite hydrogel consisting of Na‐montmorillonite with enhanced mechanical properties

A new kind of nanocomposite (NC) hydrogel with Na‐montmorillonite (MMT) is presented in this article. The NC hydrogels were synthesized by free radical copolymerization of acrylamide and (3‐acrylamidopropyl) trimethylammonium chloride (ATC) in the presence of MMT and N,N′‐methylene‐bis‐acrylamide used as chemical cross‐linker. Due to the cation‐exchange reaction between MMT and ATC (cationic monomer) during the synthesis of NC hydrogels, MMT platelets were considered chemical “plane” cross‐linkers, different from “point” cross‐linkers. With increasing amount of MMT, the crosslinking degree enhanced, causing a decrease of the swelling degree at equilibrium. Investigations of mechanical properties indicated that NC hydrogels exhibited enhanced strength and toughness, which resulted from chemical interaction between exfoliated MMT platelets and polymer chains in hydrogels. Dynamic shear measurements showed that both storage modulus and loss modulus increased with increasing MMT content. The idea described here provided a new route to prepare hydrogels with high mechanical properties by using alternative natural Na‐MMT. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1020–1026     

Strategies for synthesizing non-bioaccumulable alternatives to PFOA and PFOS

This minireview describes the strategies for synthesis of fiuorinated surfactants potentially nonbioaccumulable.Various strategies have been focused on(Ⅰ) reducing the length of the perfluorocarbon chain,(Ⅱ) introducing hetero atoms into the fluorocarbon chain,(Ⅲ) introducing branch(herein and after branch means the fluoro-carbon chain section is not straight).In most cases,the surface tensions versus the surfactant concentrations have been assessed.These above strategies led to various highly fiuorinated(perfluorinated or not perfluorinated) surfactants whose chemical changes enabled to obtain novel alternatives to perfluorooctanoic acid(PFOA) and perfluorooctane sulphonate(PFOS).     

Facile fabrication of fast recyclable and multiple self‐healing epoxy materials through diels‐alder adduct cross‐linker

A reversibly cross‐linked epoxy resin with efficient reprocessing and intrinsic self‐healing was prepared from a diamine Diels‐Alder (DA) adduct cross‐linker and a commercial epoxy oligomer. The newly synthesized diamine cross‐linker, comprising a DA adduct of furan and maleimide moieties, can cure epoxy monomer/oligomer with thermal reversibility. The reversible transition between cross‐linked state and linear architecture endows the cured epoxy with rapid recyclability and repeated healability. The reversibly cross‐linked epoxy fundamentally behaves as typical thermosets at ambient conditions yet can be fast reprocessed at elevated temperature like thermoplastics. As a potential reversible adhesive, the epoxy polymer with adhesive strength values about 3 MPa showed full recovery after repeated fracture‐thermal healing processes. The methodology explored in this contribution provides new insights in modification of conventional engineering plastics as functional materials. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2094–2103     

铁分子Fe2的自旋极化效应

采用密度泛函方法(B3P86)对 Fe_2分子结构进行了优化.计算结果中未观察到自旋污染,基态波函数与高态波函数并未混杂,结果表明,Fe_2中有8个未配对电子,这些电子空间分布不同和自旋平行产生的自旋极化效应,使 Fe_2能量最低.计算结果表明,Fe_2分子的基态是~9∑_g~ ,并非~7Δ_u,进而表明 Fe_2的自旋平行效应比电子自旋配对效应要强.计算得到该分子基态的二阶、三阶和四阶力常数分别为1.4115×10~(-2)aJ/nm~2、-37.1751×10~3aJ/nm~3和 98.7596×10~4aJ/nm~4；光谱数据ω_eχ_e、B_e、α_e分别为0.3522、0.0345、 0.4963×10~(-4)cm~(-1)；离解能为3.5522eV,平衡键长为0.2137nm,振动频率为292.914cm~(-1)；并得到了 Murrel-Sorbie 函数.     

Banach空间中优化问题的最优性条件

首先在Contingent切锥意义下界定了Banach空间中非空集合的伪切锥和伪凸性的概念，并讨论了相应的性质，然后针对可微优化问题，在广义凸性假设下，建立了最优性条件。     

Molecular dynamics simulation of processing using AFM pin tool

A three-dimensional molecular dynamics (MD) model is utilized to investigate the effect of tool geometry on the deformation process of the workpiece and the nature of deformation process at the atomic-scale. Results show that different states exist between the atomic force microscope (AFM) pin tool and the workpiece surface, i.e. the non-wear state, the ploughing state, the state in which ploughing is dominant and the state in which cutting plays a key role. A relationship between the deformation process of the workpiece and the potential energy variation is presented. The potential energy variation of atoms in different deformed regions in the workpiece such as plastically deformed region, elastically deformed region and the mixed deformation region is different. The features of variations of potential energy are discussed.     

两种拔尿管方法对膀胱功能损伤的临床观察

为观察两种不同的拔尿管方法对膀胱功能损伤的差异,将80例患者随机分成两组,分别采用改良法(40例)和常规法(40例)拔除留置尿管,分析比较了两组患者排尿顺利率、逼尿肌功能恢复率及尿道刺激症、尿失禁、尿潴留。结果表明,两组患者拔管后上述指标与情况有显著性差异,P<0.05。提示改良组膀胱功能损伤明显低于对照组。改良的拔管方法是一种值得护理推广应用的好方法。     

金属β-二酮化合物用于MOCVD法生长铁电氧化物薄膜

对用于MOCVD法生长铁电氧化物薄膜的金属β－二酮化合物的制备、结构及性质进行了评述，对它们在生长铁电薄膜中的应用现状进行了介绍，并对它们的应用前景作了展望。