Path to achieving molecular dispersion in a dense reactive mixture

A uniform dispersion of reactants is necessary to achieve a complete reaction involving multicomponents. In this study, we have examined the role of plasticizer in the reaction of two seemingly unlikely reactants: a highly crystalline hexamethylenetetramine (HMTA) and a strongly hydrogen bonded phenol formaldehyde resin. By combining information from NMR, infrared spectroscopy and differential scanning calorimetry, we were able to determine the role of specific intermolecular interactions necessary for the plasticizer to dissolve the highly crystalline HMTA and to plasticize the phenol formaldehyde resin in this crosslinking reaction. The presence of the plasticizer increased the segmental mobility, disrupted the hydrogen bonded matrix, and freed the hydroxyl units, which further increased the solubility of the HMTA. Both the endothermic and exothermic transitions are accounted for in the calorimetric data obtained. For the first time, it is possible to obtain the effective molar ratio of each component needed to complete the crosslinking reaction efficiently. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1519–1526     

Application of pressure sensitive paint measurement to a low-solidity cascade diffuser of a transonic centrifugal compressor

A pressure sensitive paint (PSP) measurement has been known as a pressure field measurement technique based on the oxygen quenching phenomenon of luminescence of specific luminophores. A PSP measurement was applied for pressure field measurement in a low-solidity circular cascade diffuser of a single-stage transonic centrifugal compressor with 5 in pressure ratio for HFC134a gas. The oxygen concentration was about 500 ppm. Ru (bath-phen) was adsorbed on a silica-gel thinlayer chromatography sheet, and the sheet was pasted onto the side-wall between the cascade vanes. A drastic change in luminescent intensity was recognized during a surge condition. Also the pressure variations based on luminescent intensity agreed well with the pressure fluctuations measured using a semiconductor pressure sensor with high-frequency-response. It was shown that a PSP measurement worked well to investigate the unsteady pressure fields in a circular cascade diffuser of a transonic centrifugal compressor. Moreover, the time response of PSP becomes clear as a problem to be overcome for the present.     

Dynamic and subjective responses of seated subjects exposed to simultaneous vertical and fore-and-aft whole-body vibration: The effect of the phase between the two single-axis components

Subjective and dynamic responses of seated subjects exposed to simultaneous vertical and fore-and-aft sinusoidal whole-body vibration were investigated. The effect of the phase difference between the vertical and the fore-and-aft vibration on the responses was of a particular interest in this study. Fifteen subjects were exposed to dual-axis vibrations at six frequencies (2.5-8 Hz) and at eight phases between the two single-axis components (0-315°). The magnitude of vibration in each axis was constant at 0.7 m s⁻² rms. Discomfort caused by vibration was measured by the method of magnitude estimation. The motion of the body were measured at the head and three locations along the spine with accelerometers attached to the body surface. The most significant effect of the phase between the two single-axis components on the discomfort was observed at 5 Hz: about 40% difference in the median discomfort estimate caused by changing the phase. The transmissibilities from vertical seat vibration to vertical motions of the spine varied from 0.5 to 2.0 by changing the phase between the two single-axis components at frequencies from 2.5 to 5 Hz. The effect of the phase observed in the dynamic response was not predicted by the superposition of the responses to each single-axis vibration. The discomfort caused by the dual-axis vibration tended to be correlated better with the combinations of the dynamic responses measured in the two axes than with the dynamic responses in a single axis.     

Anisotropic friction model of DNA electrophoresis in polymer solutions: Comparison with direct observations

The electrophoresis of DNA chains in uncrosslinked polymer solutions with a Brownian dynamics simulation with an anisotropic friction tensor was analyzed. According to the degree of anisotropy, three types of migration behavior are obtained: fluctuation without or with periodicity between U‐shaped and compact conformations, or migration with linear conformation. We found good agreement between our simulation results and the direct observations of DNA by fluorescence microscopy. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1316–1322, 2003     

Direct observation of chemical oscillation at a water/nitrobenzene interface with a sodium-alkyl-sulfate system.

The oscillation of the interfacial tension and electrical potential at a water/nitrobenzene interface was observed with homologous anionic surfactant molecules, sodium-alkyl-sulfates. Concerning small molecules with a short hydrophobic carbon chain, the oscillation period and amplitude decreased with a decrease of the length of the alkyl chain. On the other hand, when surfactant molecules with a long hydrophobic carbon chain were used, no remarkable periodic oscillation occurred after the first oscillation. In all systems, an interfacial flow by Marangoni convection was observed when the oscillation took place. By monitoring the movement of carbon powder scattered on the liquid/liquid interface with a CCD camera, we could observe that the liquid/liquid interface expanded outward from the area on which the surfactant molecules adsorbed when the oscillation occurred. When the small molecule was used, the speed of expansion of the interface (flow speed) was small and shrinkage followed by expansion of the interface repeatedly occurred. However, when the large molecule was used, the flow speed was large and expansion occurred only one time. These results show that hydrodynamic factors and surface activities are important in chemical oscillation systems.     

High-throughput characterization of local conductivity of Nd0.9Ca0.1Ba2Cu3O7−δ thin film by the low-temperature scanning microwave microscope

We developed a scanning microwave microscope (SμM) designed for high-throughput electric-property screening as well as for rapid construction of electronic phase diagrams at low temperatures. As a sensor probe, we used a high-Qλ/4 coaxial cavity resonator to which a thin needle with ball-tip end was attached. The sensor module was mounted on the low-temperature XYZ stage, which allowed us to map out the change of resonance frequency and quality factor due to the local tip-sample interaction at low temperatures. From the measurements of combinatorial thin films, such as Ti_1−xCo_xO_2−δ and Nd_0.9Ca_0.1Ba₂Cu₃O_7−δ (NCBCO), it was demonstrated that this SμM system has enough performance for the high-throughput characterization of sample conductance under variable temperature conditions.     

Effect of Hydrolysis Conditions on the Direct Formation of Nanoparticles of Ceria–Zirconia Solid Solutions from Acidic Aqueous Solutions

The effect of the cation concentration, hydrolysis temperature, and composition in the CeO₂–ZrO₂ system on the direct precipitation of ceria–zirconia solid solutions and the structure of the precipitates from acidic aqueous solutions of (NH₄)₂Ce(NO₃)₆ and ZrOCl₂ by hydrolysis under hydrothermal conditions were investigated. Nanometer-sized (8–10 nm) ceria–zirconia solid solution particles in a composition range of 0 to 60 mol% ZrO₂ were directly precipitated from the solutions with total metal cation concentration less than 0.2 mol/dm³ by simultaneous thermal hydrolysis at 150–240°C. The crystalline phase of the precipitates gradually changed from cubic and/or tetragonal to monoclinic with increasing the cation concentration of the solution from 0.2 to 0.8 mol/dm³ at the starting composition of 50 mol% ZrO₂ under hydrolysis condition of 150°C for 48 h, which was attributed to decrease in the supply of hydrolyzed Ce component caused by decrease in the hydrolysis ratio of (NH₄)₂Ce(NO₃)₆. Ceria–zirconia solid solutions containing large amount of ZrO₂ maintained high specific surface area and small-sized crystallite after heat-treatment at 900–1000°C for 1 h.