The effect of electron withdrawing croups on the stability of thiabenzenes

The reactions of p-trifluoromethylphenyllithium with 2,4,6-triarylthiopyrylium perehlorates (Ar = Ph, p-CH₃OC₆H₄, p-NMe₂C₆H₄) have been studied. The initially formed thiabenzenes were not slable enough to he isolated and rearranged readily to their corresponding 4-(p-tri-fluoromethylphenyl)-2,4,6-triarylthiopyrans. The instability of the intermediate thiabenzenes reveals that, in contrast to the stabilization effect of the electron-withdrawing p-chloro- and pentalluorophcnyl groups attached to carbon atoms in sulfur ring, the electron-withdrawing p-lrilluoromethyl group on subsliluenls attached to sulfur decreases the stability of thiabenzenes.     

Polyvinylimidazole/sol–gel composite as a novel solid‐phase microextraction coating for the determination of halogenated benzenes from aqueous solutions

A polyvinylimidazole/sol–gel composite is proposed as a novel solid‐phase microextraction fiber to extract five halobenzenes from the headspace of aqueous solutions in combination with gas chromatography with mass spectrometry. The prepared fiber was characterized by scanning electron microscopy and Fourier transform infrared spectroscopy. The obtained results showed that porous polyvinylimidazole/sol–gel composite was chemically deposited on fused silica fiber. The effect of important extraction parameters including extraction temperature, extraction time, and salt content were investigated. The optimum conditions were as follows: extraction temperature 25°C, extraction time 20 min, and salt concentration 30 w/v%. Detection limits and relative standard deviations of the developed method for halogenated benzenes were below 0.1 pg/mL and 15%, respectively. Repeatability of the proposed method, explained by relative standard deviation, varied between 5.48 and 9.15% (n = 5). The limits of detection (S/N = 3) ranged between 0.01 and 0.10 ng/L using gas chromatography with mass spectrometry with selected ion monitoring mode. For real sample analysis, three types of water samples with different matrices (ground, surface, and tap water) were studied. The optimized procedure was applied to extraction and method validation of halogenated benzenes in spiked water samples.     

Single quantum dot (QD) imaging of fluid flow near surfaces

We introduce the use of quantum dot (QD) nanoparticles for near-surface velocimetry and provide preliminary data to demonstrate its feasibility. Evanescent wave illumination is used to image the motion of water-soluble (CdSe)ZnS QDs with a core size of 6 nm within a region of order 100 nm of a surface . Results are presented for the two in-plane components of the velocity field.     

Multi-photon molecular tagging velocimetry with femtosecond excitation (FemtoMTV)

We present results for first molecular tagging velocimetry (MTV) measurements in water under resonant femtosecond excitation/emission process of a phosphorescent supramolecule. Both two-photon and three-photon absorption processes are examined, and the feasibility of measurements is demonstrated by single component velocimetry in a simple jet flow. The new capabilities enabled by FemtoMTV include elimination of the need for short wavelength UV excitation source and UV optical access in flow facilities, and potential for high rep-rate flow imaging.     

In situ LIF temperature measurements in aqueous ammonium chloride solution during uni-directional solidification

We present in situ whole-field measurements of the temperature field using laser-induced fluorescence in a study of bottom-chilled uni-directional solidification of aqueous ammonium chloride. We utilize a two-color, two-dye, ratiometric approach to address the significant spatial and temporal variations of laser sheet intensity field due to refractive index variations caused by the evolving concentration and temperature fields. In our work we take advantage of two temperature sensitive fluorescent dyes with opposite temperature sensitivities in order to increase the overall sensitivity and temperature resolution of the measurements. The resulting temperature sensitivity (about 4% K⁻¹) is more than a factor of two higher than the original work of Sakakibara and Adrian (Exp Fluids 26:7–15, 1999) with a sensitivity 1.7% K⁻¹. In situ measurements of the temperature field during solidification are presented, along with temperature characteristics of some of the complex flow features, such as plumes and fingers.     

A method for estimating wall friction in turbulent wall-bounded flows

We describe a simple method for estimating turbulent boundary layer wall friction using the fit of measured velocity data to a boundary layer model profile that extends the logarithmic profile all the way to the wall. Two models for the boundary layer profile are examined, the power-series interpolation scheme of Spalding and the Musker profile which is based on the eddy viscosity concept. The performance of the method is quantified using recent experimental data in zero pressure gradient flat-plate turbulent boundary layers, and favorable pressure gradient turbulent boundary layers in a pipe, for which independent measurements of wall shear are also available. Between the two model profiles tested, the Musker profile performs much better than the Spalding profile. Results show that the new procedure can provide highly accurate estimates of wall shear with a mean error of about 0.5% in friction velocity, or 1% in shear stress, an accuracy that is comparable to that from independent direct measurements of wall shear stress. An important advantage of the method is its ability to provide accurate estimates of wall shear not only based on many data points in a velocity profile but also very sparse data points in the velocity profile, including only a single data point such as that originating from a near-wall probe.     

All‐in‐one solid‐phase microextraction: Development of a selective solid‐phase microextraction fiber assembly for the simultaneous and efficient extraction of analytes with different polarities

In the present work, for the first time, an all‐in‐one solid‐phase microextraction technique was developed for the simultaneous and efficient extraction of analytes within a vast polarity range. A novel fiber assembly composed of two different steel components each coated with different coatings (polydimethylsiloxane and polyethylene glycol) in terms of polarity by sol–gel technology was employed for the extraction of model compounds of different polarity in a single run followed by gas chromatography with mass spectrometry. Effective parameters in the extraction step and gas chromatography with mass spectrometry analysis were optimized for all model compounds. The detection limits of the developed method for model compounds were below 0.2 ng/L. The repeatability and reproducibility of the proposed method, explained by relative standard deviation, varied between 7.22 and 9.15% and between 7.95 and 14.90 (n = 5), respectively. Results showed that, under random conditions, compared to separate extractions performed by two other differently end‐coated components that had not been assembled as the final dual fiber, as two individual fibers; simultaneous, efficient and relatively selective extraction of all model compounds was obtained in a single run by the proposed all‐in‐one technique. Finally, the optimized procedure was applied to extraction and determination of the model compounds in spiked water samples.     

Thermal characterization and kinetic analysis of nano‐ and micro‐Al/NiO thermites: Combined experimental and molecular dynamics simulation study

In the experimental part of this study, thermal properties of the Al and NiO composites in micro‐ and nano‐sized Al are investigated. Differential scanning calorimetry (DSC) analysis of the onset temperatures of ignition, activation energy (E_a), frequency factor (A), rate constant (k), critical ignition temperature of thermal explosion (T_b), and self‐accelerating decomposition temperature (T_SADT), as well as the thermodynamic parameters (ΔS^≠ , ΔH^≠ , and ΔG^≠ ) are used to explore the thermal behavior and analyze the kinetics. Thermal analysis suggests that the mechanism is based on solid–solid diffusion and liquid–gas for the nano‐ and micro‐Al/NiO composite, respectively. Our results indicate that the incorporation of nano‐Al particles can significantly reduce the ignition temperature, E_a, A, k, T_b, and T_SADT. In the second part of this work, molecular dynamics (MD) simulation is used to investigate the behavior of Al/NiO thermite reaction using the Reaxff force field to evaluate the experimental results. Theoretically, MD results show 1,154 K as the reaction ignition temperature, which is in reasonably good agreement with experimental temperature of 893°C (1,166 K). The radial distribution function (RDF) shows that no reaction occurs at 500 K but it is complete at 1,200 K.     

Using nucleators to control freckles in unidirectional solidification

Buoyancy-induced fluid flow, which is responsible for most forms of macro-segregation and channel-type segregates in castings, is not directly controllable. If left uncontrolled, natural convection will contribute to non-uniform distribution of alloy constituents and grain structure during solidification of a casting. Non-uniform distribution of chemical composition and physical structure in an alloy casting can significantly affect the reliability of mechanical components. Therefore, materials with acceptable defects can be produced only by trial-and-error and their acceptability is determined by costly inspections. We present a novel technique to control the formation of chimneys and resulting freckles in the mushy zone during the solidification of ammonium chloride that is cooled from below. This is done by placing metallic nucleators in particular arrangements on the bottom cooling plate. With this technique, freckles in a casting might be avoided and/or be forced to form where stresses are expected to be lower during use of the part.The objective of this study is to investigate the effects of the arrangement, spacing, and size of the nucleators on finger formation, plume structure, and the solidification process. Results showed that it is possible to obtain a relatively large area free of channel-segregates in a metal analog directionally solidified upward by placing nucleators in certain arrangements at the bottom of the casting. The outcomes of this study will serve as a baseline for subsequent investigations that will examine the solidification of binary alloys, and could be used to test and develop mathematical and numerical models.     

Convergent One‐Pot Synthesis of 3‐Substituted Quinazolin‐4(3H)‐ones under Solvent‐Free Conditions

A convenient method for the synthesis of 3‐substituted quinazolin‐4(3H)‐ones using the convergent reactions of formic acid, a primary amine, and isatoic anhydride under solvent‐free conditions and with brief microwave irradiation is described.