Microfluidic synthesis of chitosan-based nanoparticles for fuel cell applications

A microfluidic platform is developed for the synthesis of monodisperse, 100 nm, chitosan based nanoparticles using nanogelation with ATP. The resulting nanoparticles tuned and enhanced transport and electrochemical properties of Nafion based nanocomposite membranes, which is highly favorable for fuel cell applications.     

Evaluation of a cloud point extraction approach for the preconcentration and quantification of trace CuO nanoparticles in environmental waters

The cloud point extraction (CPE) of commercial copper(II) oxide nanoparticles (CuO NPs, mean diameter of 28 nm) in water samples was fully investigated. Factors such as Triton X-114 (TX-114) concentration, pH, incubation temperature and time, were optimized. The effects of CuO NP behavior like agglomeration, dissolution, and surface adsorption of natural organic matter, Cu²⁺, and coating chemicals, on its recovery were studied. The results indicated that all the CPE factors had significant effects on the extraction efficiency. An enrichment factor of ∼89 was obtained under optimum CPE conditions. The hydrodynamic diameter of CuO NPs increased to 4–5 μm upon agglomeration of NP-micelle assemblies, and decreased at pH >10.0 at which the extraction efficiency was also lowered. The solubility and therefore, the loss of NPs were greatly enhanced at pH <8.5 and in the first 60 min of incubation, whereas it declined at elevated incubation temperatures. Our results showed that the dissolved organic carbon (DOC) >5 mg C L⁻¹ and Cu²⁺ >2 times that of CuO NPs, lowered and enhanced the extraction efficiency, respectively. Pre-treatment of samples with 3% w v⁻¹ of hydrogen peroxide and 10 mM of ethylenediaminetetraacetic acid minimized the interferences posed by DOC and Cu²⁺, respectively. The decrease in CPE efficiency was also evident for ligands like poly(ethylene glycol). The TX-114-rich phase could be determined with either inductively coupled plasma mass spectrometry following microwave digestion, or graphite furnace atomic absorption spectrometry. The detection limits for CuO NPs were 0.02 and 0.06 μg L⁻¹ using these techniques, respectively. The optimum sample pre-treatment and CPE conditions were successfully applied to the river and wastewater samples. The relative recoveries of CuO NPs spiked at 5–100 μg L⁻¹ (as Cu) in these samples were in the range of between 59.2 and 108.2%. The approach demonstrates a robust analytical method for detecting trace levels of CuO NPs at their original states and assessing their exposure risks in real aquatic environments.     

Sol-gel preparation and characterization of Co/TiO<Subscript>2</Subscript> nanoparticles: Application to the degradation of methyl orange

Cobalt doped titania nanoparticles were synthesized by sol-gel method using titanium(IV) isopropoxide and cobalt nitrate as precursors. X-Ray diffraction (XRD) results showed that titania and Co/TiO₂ nanoparticles only include anatase phase. The framework substitution of Co in TiO₂ nanoparticles was established by XRD, scanning electron microscopy equipped with energy dispersive X-ray microanalysis (SEM-EDX) and Fourier transform infrared (FT-IR) techniques. Transmission electron microscopy (TEM) images confirmed the nanocrystalline nature of Co/TiO₂. The increase of cobalt doping enhanced “red-shift” in the UV-Vis absorption spectra. The dopant suppresses the growth of TiO₂ grains, agglomerates them and shifts the band absorption of TiO₂ from ultraviolet (UV) to visible region. The photocatalytic activity of samples was tested for degradation of methyl orange (MO) solutions. Although the photocatalytic activity of undoped TiO₂ was found to be higher than that of Co/TiO₂ under UV irradiation, the presence of 0.5% Co dopant in TiO₂ resulted in a catalyst with the highest activity under visible irradiation.     

Synthesis, characterization and effect of calcination temperature on phase transformation and photocatalytic activity of Cu,S-codoped TiO2 nanoparticles

A novel copper and sulfur codoped TiO₂ photocatalyst was synthesized by modified sol-gel method using titanium(IV) isopropoxide, CuCl₂·2H₂O and thiourea as precursors. The samples were characterized by X-ray diffraction (XRD), diffuse reflectance spectroscopy (DRS), scanning electron microscopy equipped with energy dispersive X-ray micro-analysis (SEM-EDX), transmission electron microscopy (TEM) and Fourier transform infrared (FT-IR) analysis. The XRD results showed undoped and Cu,S-codoped TiO₂ nanoparticles only include anatase phase. Effect of calcination temperature showed rutile phase appears in 650 and 700 °C for undoped and 0.1% Cu,S-codoped TiO₂, respectively. The SEM analysis revealed the doping of Cu and S does not leave any change in morphology of the catalyst surface. The increase of copper doping enhanced “red-shift” in the UV-vis absorption spectra. The TEM images confirmed the dopants suppressed the growth of TiO₂ grains. The photocatalytic activity of samples was tested for degradation of methyl orange (MO) solutions. The results showed photocatalytic activity of the catalysts with 0.05% Cu,0.05% S and 0.1% Cu,0.05% S were higher than that of other catalysts under ultraviolet (UV) and visible irradiation, respectively. Because of synergetic effect of S and Cu, the Cu,S-codoped TiO₂ catalyst has higher activity than undoped and Cu or S doped TiO₂ catalysts.     

Bis(trimethylsilyl)chromate catalyzed oxidations of alcohols to aldehydes and ketones with periodic acid

A facile, selective and high yielding bis(trimethylsilyl) chromate (BTSC) catalyzed selective oxidation of alcohols to aldehydes and ketones with periodic acid is reported.     

Efficient hydrophobization and solvent microextraction for determination of trace nano-sized silver and titanium dioxide in natural waters

Hydrophobic silver and titanium (IV) oxide nanoparticles (commercial Ag and TiO₂ NPs with average particle sizes of 17 and 19 nm, respectively) were quantitatively transferred into organic phase in natural water samples. Five NP surface modification and solvent extraction agents (reagents) types, mercaptocarboxylic acid, alkylamine, mediator solvent, extraction solvent, and surfactant, were investigated and optimized with three-level orthogonal array design (OAD), an OA₂₇ (3¹³) matrix. The most favorable reagents and experimental conditions were then examined. The best extraction efficiencies of 78.6 and 73.7% were obtained for 1 mg L⁻¹ citrate-stabilized Ag and TiO₂ NPs, respectively, with 0.5 mM of 11-mercaptoundecanoic acid, 1.5 mM of octadecylamine, 1 mL of methanol, 150 μL of cyclohexane, 0.05 mM of tetra-n-octylammonium bromide, pH = 8.0, adsorption time of 2 h, sonication time of 3 min, and centrifugation time of 10 min. Enrichment factors were 97 and 83, for Ag and TiO₂ NPs, respectively. The optimum extraction conditions were successfully applied to genuine water samples at spiking levels of 2–100 μg L⁻¹ of Ag and TiO₂ NPs. The relative recoveries of (69.0–85.1)% and (61.5–78.5)% were obtained for Ag and TiO₂ NPs, respectively. The extracted surface-modified NPs were characterized with transmission electron microscopy, selected area electron diffraction, energy-dispersive X-ray, ultraviolet–visible, and Fourier transform infrared spectroscopic techniques. Based on the results, efficient ligand exchange and acid–base pair formation were observed on the NP surface without significant change in its original properties. The organic phase was microwave digested, and analyzed with inductively coupled plasma (ICP) optical emission spectroscopy and ICP mass spectrometry (ICP-MS). Detection limits of ICP-MS analyses of Ag and TiO₂ NPs were 0.02 and 0.07 μg L⁻¹, respectively.     

Characterization of nanohybrid membranes for direct methanol fuel cell applications

A series of sulfonated poly(2,6-dimethyl-1,4-phenylene oxide) (S-PPO) and sulfonated poly(ether ether ketone) (S-PEEK) at various sulfonation degrees were prepared and characterized for their degree of sulfonation, water uptake, ion exchange capacity, proton conductivity and methanol permeability. Based on the obtained results, the optimum samples were determined and subsequently blended together at different compositions. A single glass transition temperature (T_g) was determined for all blend samples, which was attributed to the presence of sulfonate groups on polymer backbones resulting in the formation of electrostatic cross-linking besides phenyl–phenyl interactions. Moreover, the molecular level of mixing in blends was verified through WAXS patterns. According to the membrane selectivity and hydrolytic stability measurements, 75 wt.% of S-PPO and 25 wt.% of S-PEEK was selected as the optimum composition. Afterwards, different amounts of an organically modified montmorillonite (MMT) were incorporated into the predetermined optimum composition matrices to reduce the methanol permeability of the resulted nanocomposite proton exchange membranes. The XRD patterns of nanocomposites revealed the exfoliated microstructure of the clay nanolayers in the polymeric matrices. Transport property measurements of nanohybrid membranes showed that the maximum selectivity parameter of 75 wt.% S-PPO/25 wt.% S-PEEK composition appeared in the presence of 1.5 wt.% of MMT, which is 1.53 times higher than the corresponding value for Nafion^® 117. The DMFC single cell test of the optimum nanohybrids membrane at 5 M methanol feed showed an open circuit voltage of 0.77 V and maximum power density of 135 mW cm^? 2 in comparison with 0.67 V and 108 mW cm^? 2 for Nafion^® 117, respectively. Fabricated nanohybrid membranes, thanks to their high selectivity, desirable transport properties and tenability, could be considered as promising polyelectrolytes for direct methanol fuel cell applications.     

Polybenzimidazole‐decorated carbon nanotube: A high‐performance proton conductor

Interaction between negatively charged Nafion^® and a positively charged polybenzimidazole‐decorated carbon nanotube leads to the formation of an ionic complex with high charge density for proton conduction, which can lead to an improvement in transport properties. Here we investigate the high‐temperature and low‐humidity proton conductivity of this nanocomposite membrane as a potential membrane for fuel cell applications.