On-line Method for Montelukast Determination in Bile Salt Medium with Multivariate Optimization and Fluorescent Detection

Journal of Analytical Chemistry - The present development involved a flow injection strategy using a mini-column of multiwalled carbon nanotubes and fluorescent detection (λex of 283 nm,...     

Combined effects of clay modifications and compatibilizers on the formation and physical properties of melt‐mixed polypropylene/clay nanocomposites

The melt mixing technique was used to prepare various polypropylene (PP)‐based (nano)composites. Two commercial organoclays (denoted 20A and 30B) served as the fillers for the PP matrix, and two different maleated (so‐called) compatibilizers (denoted PP‐MA and SMA) were employed as the third component. The results from X‐ray diffraction (XRD) and transmission electron microscope (TEM) experiments revealed that 190 °C was an adequate temperature for preparing the nanocomposites. Nanocomposites were achieved only if specific pairs of organoclay and compatibilizer were simultaneously incorporated in the PP matrix. For example, PP/20A(5 wt %)/PP‐MA(10 wt %) and PP/30B(5 wt %)/SMA(5 wt %) composites exhibited nanoscaled dispersion of 20A or 30B in the PP matrix. Differential scanning calorimetry (DSC) results indicated that the organoclays served as nucleation agents for the PP matrix. Generally, their nucleation effectiveness increased with the addition of compatibilizers. The thermal stability enhancement of PP after adding 20A was confirmed with thermogravimetric analysis (TGA). The enhancement became more evident as a suitable compatibilizer was further added. However, for the 30B‐included composites, thermal stability enhancement was not evident. The dynamic mechanical properties (i.e., storage modulus and loss modulus) of PP increased as the nanocomposites were formed; the properties increment corresponded to the organoclay dispersion status in the matrix. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4139–4150, 2004     

Structure and reflective properties of Al-Cu-Fe quasicrystalline thin film prepared by laser induced arc method

Al-Cu-Fe thin films were prepared by laser induced arc (laser-arc) method from a single source—Al₆₃Cu₂₅Fe₁₂ alloy, which was proved to consist of quasicrystalline phase together with approximant phase. The composition of the deposited films meets the requirement for formation of icosahedral symmetry phase. Quasicrystalline phase was obtained after annealing the amorphous as-deposit film samples. The optical properties of the samples were investigated. Thin film samples of Al, Cu and Fe deposited under the same condition were employed for comparison. The results showed specific reflective properties of Al-Cu-Fe quasicrystal thin film in some wavelength range. The optical conductivity of the films exhibited a negative peak, centered about 440 nm in range of 190 to 800 nm. The Al-Cu-Fe quasicrystal thin films could absorb almost all the ray in the wavelength range from 420nm to 450 nm. The ratio of absorption was greater than 99%.     

Numerical method and models for anti-plane strain of a system with a thin elastic wedge

The paper presents a general method to find asymptotics for a (multi-)wedge system containing a thin wedge. It employs separation of the symmetric and anti-symmetric parts of the boundary displacements and tractions of the wedge. The method is applicable when the angle of the thin wedge turns to zero. A physical interpretation of the derived equations is obtained by using power expansions of non-polynomial functions, which appear after the Mellin transform. We establish that the first term in the expansion of the symmetric part corresponds to shear, while the first term of the anti-symmetric part describes deflection of the wedge axis. Numerical experiments, performed by using a code developed on the basis of the theory, show that using only the first terms of the expansions insignificantly influence accuracy: the approximate results coincide with the exact values of roots to the third significant digit even for the wedge angle of 30°.     

Indirect fluorometric determination of diclofenac sodium.

A simple and easy method of analysis for diclofenac sodium is reported. A spectrofluorometric method for the microdetermination of diclofenac sodium has been developed through its reaction with cerium(IV) in an acidic solution and measurement of the fluorescence of the Ce(III) ions produced. Under the optimum experimental conditions for the oxidation reaction, 1.0 M H2SO4 with 90 min of heating time (100 degrees C), the range of application is 124.3-600 ng mL(-1) and the limit of detection is 72.7 ng mL(-1). The proposed method was applied to the determination of diclofenac sodium in pharmaceutical tablets. The results of the analysis show a good agreement with those obtained by the official USP 27 HPLC method.     

关于meso—四苯基卟啉在冰醋酸中的存在形式

前言卟啉在生物化学、分析化学、药物化学等领域有着广泛研究和重要应用［１～３］。近年来虽然对卟啉类化合物的研究报道很多［４～６］，但对卟啉在酸性介质中的研究很少。较早期的研究工作认为卟啉类化合物在酸性介质中仅以其二酸形式存在［７］。本文实验结果显示ｍｅ...     

Co-immobilization of polymeric luminol,iron(II) tris(5-aminophenanthroline) and glucose oxidase at an electrode surface,and its application as a glucose optrode

The anodic polymerization of 3-aminophthalhydrazide (luminol) and iron(II) tris 5-aminophenanthroline (Fe(phen-NH2)3(2+)) has been reported in this paper. A bilayer electrode was developed based on these polymers and the ITO conductive glass (denoted ITO[Fe(phen-NH2)3(2+)]luminol electrode). This electrode emitted light (lambdaem: 430 nm) as it was brought into contact with H2O2. At pH 10, the resulting electrochemiluminescence (ECL) showed a linear relationship with the concentration of H2O2 in the range of 10 microM(-1) mM. This bilayer electrode also showed an application potential for the detection of glucose after being further modified with glucose oxidase (denoted ITO[Fe(phen-NH2)3(2+)]luminol]GOx electrode). Although the resulting ECL decayed more rapidly in concentrated glucose solutions (e.g., I M) because of the consumption of luminol during use, the decay became less severe in diluted glucose solutions (e.g., 10 mM). According to the flow injection analysis, a linear relationship existed between the ECL and the concentration of glucose from 10(-5)-10(-3) M at pH 9. The detection limit could reach a level of 5 x 10(-5) M at this pH.     

Size of Micelles Determined by Static Fluorescence Quenching

We developed a new method to measure the average aggregation number of large rod-like micelles using static fluorescence self-quenching of a solubilized fluorophore. The method is based on the increase of self-quenching of micelle-solubilized pyrene through excimer formation. We consider the effect of random distribution of pyrene in micelles and the micellar size distribution. The measured average aggregation <n> _M is based on a new M-weighted raging similar to our exponential-weighted averaging in the transient decay method. We apply this method to study the effect of a large concentration of salt on the average aggregation behavior of sodium dodecyl sulfate (SDS) and cetyle tetraammonium bromide (CTAB). The sizes increase with increasing ionic concentrations. For SDS, we used the thermodynamic model developed by Missel et al. to calculate < n > _M which we compare with experimental results.